[fedora-arm] testing Fedora-Minimal-armhfp-30-20190326.n.0-sda on Cubieboard2

I am at IETF104, and only brought a Cubieboard2 and forgot my sata drive and sata adapter.  Thus all testing is uSD and USB only until next Monday. I installed minimal on a 4GB uSD and deleted all partitions, leaving only the uboot. I installed minimal on a 16GB uSD and expanded the rootfs to the full size of the card. First test was uboot only in the uSD slot and the full image USB connected (uSD USB adapter). The boot failed.  We are still on the rc2 broken uboot: U-Boot SPL 2019.04-rc2 (Feb 19 2019 - 10:00:37 +0000) DRAM: 1024 MiB CPU: 912000000Hz, AXI/AHB/APB: 3/2/2 Trying to boot from MMC1 U-Boot 2019.04-rc2 (Feb 19 2019 - 10:00:37 +0000) Allwinner Technology CPU:   Allwinner A20 (SUN7I) Model: Cubietech Cubieboard2 I2C:   ready DRAM:  1 GiB MMC:   mmc@1c0f000: 0 Loading Environment from FAT... ** No valid partitions found ** In:    serial Out:   serial Err:   serial SCSI:  SATA link 0 timeout. AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode flags: ncq stag pm led clo only pmp pio slum part ccc apst Net:   sunxi_set_gate: (CLK#66) unhandled eth0: ethernet@1c50000 starting USB... USB0:   USB EHCI 1.00 USB1:   USB OHCI 1.0 USB2:   USB EHCI 1.00 USB3:   USB OHCI 1.0 scanning bus 0 for devices... 1 USB Device(s) found scanning bus 1 for devices... 1 USB Device(s) found scanning bus 2 for devices... 2 USB Device(s) found scanning bus 3 for devices... 1 USB Device(s) found        scanning usb for storage devices... 1 Storage Device(s) found Hit any key to stop autoboot:  0 switch to partitions #0, OK mmc0 is current device ** Invalid partition 1 ** scanning bus for devices... Found 0 device(s). Device 0: unknown device Device 0: EHCI timed out on TD - token=0x80008d80 EHCI timed out on TD - token=0x80008d80 EHCI timed out on TD - token=0x80008d80 ... EHCI timed out on TD - token=0x80008d80 Vendor: Mass     Rev:
Prod: Storage Device             Type: Removable Hard Disk             Capacity: 14992.0 MB = 14.6 GB (30703616 x 512) ... is now current device EHCI timed out on TD - token=0x80008d80 EHCI timed out on TD - token=0x80008d80 ... The uboot DID recognize the USB device, but did not boot it. The second test was to put the full image in the uSD slot.  This booted up properly, went through the console first boot dialog and then I could log in as root. Next test used the F29 uboot on the 4Gb uSD in the uSD slot and the full image on the USB adapter: U-Boot SPL 2018.09 (Sep 11 2018 - 10:09:46 +0000) DRAM: 1024 MiB CPU: 912000000Hz, AXI/AHB/APB: 3/2/2 Trying to boot from MMC1 U-Boot 2018.09 (Sep 11 2018 - 10:09:46 +0000) Allwinner Technology CPU:   Allwinner A20 (SUN7I) Model: Cubietech Cubieboard2 I2C:   ready DRAM:  1 GiB MMC:   SUNXI SD/MMC: 0 Loading Environment from FAT... ** No valid partitions found ** In:    serial Out:   serial Err:   serial SCSI:  SATA link 0 timeout. AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode flags: ncq stag pm led clo only pmp pio slum part ccc apst Net:   eth0: ethernet@01c50000 starting USB... USB0:   USB EHCI 1.00 USB1:   USB OHCI 1.0 USB2:   USB EHCI 1.00 USB3:   USB OHCI 1.0 scanning bus 0 for devices... 1 USB Device(s) found scanning bus 2 for devices... 1 USB Device(s) found        scanning usb for storage devices... 0 Storage Device(s) found Hit any key to stop autoboot:  0 switch to partitions #0, OK mmc0 is current device ** Invalid partition 1 ** scanning bus for devices... Found 0 device(s). Device 0: not available Device 0: device type unknown ... is now current device Speed: 100, full duplex BOOTP broadcast 1 DHCP client bound to address 10.0.6.251 (20 ms) *** ERROR: `serverip' not set etc.... So this uboot seems better, but it is not recognizing the USB drive. Is there a later uboot than that in F29 (Fedora-Minimal-armhfp-29-1.2-sda) for me to test with? Otherwise I don't see any other testing I can do until I get back Monday.