It looks like the wrong partition. Try extload 1:1 or something. I think mine ended up on diak 1 or 2... You may have to make some other changes as well.
----- Reply message -----
From: "Robert Moskowitz" <rgm@htt-consult.com>
To: "Derek Atkins" <warlord@MIT.EDU>
Cc: "omalley_s@rocketmail.com" <omalley_s@rocketmail.com>, "Paul Whalen" <pwhalen@redhat.com>, <arm@lists.fedoraproject.org>
Subject: [fedora-arm] Bad image/instructions? - Re: Problems with a pogoplug v02
Date: Tue, Apr 23, 2013 12:22 pm
On 04/23/2013 09:03 AM, Derek Atkins wrote:
> "omalley_s@rocketmail.com" <omalley_s@rocketmail.com> writes:
>
>> Ext2ls and the usb start commands are built into uboot. You need to be at the
>> uboot prompt to use them.
> Just FTR, the default version of uboot shipped on the Guruplug Server
> (at least on the two non-Plus version I have) did not include ext
> support. I had to reflash uboot to a newer version.
I posted this in an earlier part of this thread. Here is what I see in
the nc session for the netconsole.
You tell me if it is supporting ext. I did make the documented changes
to uboot for f18 (which I don't have that link in front of me, but Scott's.
U-Boot 2011.12 (Feb 20 2012 - 21:21:59)
Pogoplug E02
arm-none-linux-gnueabi-gcc (Sourcery G++ Lite 2009q3-67) 4.4.1
GNU ld (Sourcery G++ Lite 2009q3-67) 2.19.51.20090709
Hit any key to stop autoboot: 0
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 3 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Loading file "/rescueme" from usb device 0:1 (usbda1)
Failed to mount ext2 filesystem...
** Bad ext2 partition or disk - usb 0:1 **
reading /rescueme.txt
** Unable to read "/rescueme.txt" from usb 0:1 **
Creating 1 MTD partitions on "nand0":
0x000002500000-0x000008000000 : "mtd=3"
UBI: attaching mtd1 to ubi0
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 129024 bytes
UBI: smallest flash I/O unit: 2048
UBI: sub-page size: 512
UBI: VID header offset: 512 (aligned 512)
UBI: data offset: 2048
UBI: attached mtd1 to ubi0
UBI: MTD device name: "mtd=3"
UBI: MTD device size: 91 MiB
UBI: number of good PEBs: 728
UBI: number of bad PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 0
UBI: available PEBs: 717
UBI: total number of reserved PEBs: 11
UBI: number of PEBs reserved for bad PEB handling: 7
UBI: max/mean erase counter: 1/1
UBIFS error (pid 0): ubifs_get_sb: cannot open "ubi:rootfs", error -19
Error reading superblock on volume 'ubi:rootfs'!
Loading file "uImage" from usb device 0:1 (usbda1)
Failed to mount ext2 filesystem...
** Bad ext2 partition or disk - usb 0:1 **
** Block device usb 1 not supported
** Block device usb 2 not supported
** Block device usb 3 not supported
Loading file "uImage" from usb device 0:1 (usbda1)
Failed to mount ext2 filesystem...
** Bad ext2 partition or disk - usb 0:1 **
Loading file "uInitrd" from usb device 0:1 (usbda1)
Failed to mount ext2 filesystem...
** Bad ext2 partition or disk - usb 0:1 **
Wrong Image Format for bootm command
ERROR: can't get kernel image!
stopping USB..
### JFFS2 loading 'uboot-original-mtd0.kwb' to 0x800000
Scanning JFFS2 FS: ........ done.
### JFFS2 load complete: 524288 bytes loaded to 0x800000
## Starting application at 0x00800200 ...