Hallo
ich bin einen Schritt weiter.
Die CAPI läuft jetzt für eine kurzen Moment (ca. 30 Sekunden). Danach
hat sich der komplette Rechner aufgehängt.
/var/log/messages:
Oct 28 17:58:05 linux kernel: capifs: Rev 1.1.2.3
Oct 28 17:58:06 linux kernel: capi20: Rev 1.1.2.7: started up with major
68 (middleware+capifs)
Oct 28 17:58:06 linux kernel: fcdsl: Using VCC/VPI/VCI = 0x1/0x1/0x20
Oct 28 17:58:06 linux kernel: fcdsl: Stack version 3.11-07
Oct 28 17:58:06 linux kernel: fcdsl: Stack version 3.11-07
Oct 28 17:58:06 linux kernel: kcapi: card 1 "fcdsl-eb800000-11" ready.
Oct 28 17:58:06 linux kernel: kcapi: card 2 "fcdsl-eb800000-11" ready.
Oct 28 17:58:06 linux kernel: capidrv: controller 1 up
Oct 28 17:58:06 linux kernel: fcdsl: Unknown application id! (1)
Oct 28 17:58:06 linux kernel: capidrv-1: now up (2 B channels)
Oct 28 17:58:06 linux kernel: capidrv-1: D2 trace enabled
Oct 28 17:58:06 linux kernel: fcdsl: Unknown application id! (1)
Oct 28 17:58:06 linux kernel: capidrv: controller 2 up
Oct 28 17:58:06 linux kernel: capidrv-2: now up (1 B channels)
Oct 28 17:58:06 linux kernel: capidrv-2: D2 trace enabled
das wars....
Eine Idee?
Gruß
Bruno
Am Montag, den 24.10.2005, 18:32 +0200 schrieb Christoph Wickert:
Am Montag, den 24.10.2005, 17:02 +0200 schrieb tuxbase:
> Hallo
>
> funktioniert immer noch nicht!
>
>
> dmesg:
> ISDN subsystem Rev: 1.1.2.3/1.1.2.3/1.1.2.2/1.1.2.3/1.1.2.2/1.1.2.2
> loaded
> HiSax: Linux Driver for passive ISDN cards
> HiSax: Version 3.5 (module)
> HiSax: Layer1 Revision 2.46.2.5
> HiSax: Layer2 Revision 2.30.2.4
> HiSax: TeiMgr Revision 2.20.2.3
> HiSax: Layer3 Revision 2.22.2.3
> HiSax: LinkLayer Revision 2.59.2.4
> HiSax module removed
> ISDN-subsystem unloaded
> ip_tables: (C) 2000-2002 Netfilter core team
> ip_conntrack version 2.1 (4095 buckets, 32760 max) - 248 bytes per
> conntrack
> Vendor: ICSI Model: IC1210 CF Rev: 1.6B
> Type: Direct-Access ANSI SCSI revision: 00
> Vendor: ICSI Model: IC1210 MS Rev: 1.6B
> Type: Direct-Access ANSI SCSI revision: 00
> Vendor: ICSI Model: IC1210 MMC/SD Rev: 1.6B
> Type: Direct-Access ANSI SCSI revision: 00
> Vendor: ICSI Model: IC1210 SM Rev: 1.6B
> Type: Direct-Access ANSI SCSI revision: 00
> usb-storage: device scan complete
> eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
> NET: Registered protocol family 10
> Disabled Privacy Extensions on device c0475600(lo)
> IPv6 over IPv4 tunneling driver
> CAPI Subsystem Rev 1.1.2.8
> capifs: Rev 1.1.2.3
> capi20: Rev 1.1.2.7: started up with major 68 (middleware+capifs)
> fcdsl2: module license 'Proprietary' taints kernel.
> fcdsl2: AVM FRITZ!Card DSL v2.0 driver, revision 0.3.2
> fcdsl2: (fcdsl2 built on Oct 23 2005 at 18:43:22)
> fcdsl2: -- 32 bit CAPI driver --
bis dahin ok, geht bei mir weiter mit:
> ACPI: PCI Interrupt 0000:00:0f.0[A] -> Link [LNKD] -> GSI 11 (level, low)
-> IRQ 11
> fcpci: AVM FRITZ!Card PCI found: port 0xbc00, irq 11
> fcpci: Loading...
> fcpci: Driver 'fcpci' attached to fcpci-stack. (152)
> fcpci: Stack version 3.11-07
> kcapi: Controller 1: fcpci-bc00-11 attached
> kcapi: card 1 "fcpci-bc00-11" ready.
> fcpci: Loaded.
> kcapi: contr 1 set trace=0
> kcapi: contr 1 set trace=0
> kcapi: contr 1 set trace=4
> kcapi: contr 1 set trace=0
>
> /etc/capi.conf
> fcdsl2 fds2base.bin - - - - 1
Was soll die 1 am Ende? Controller 1? Ich habe das bei meiner Fritz-DSL
v.1 nicht und in der capi.conf, die ich mal angehängt habe, ist es auch
nicht.
>
> >lsmod | egrep "capi|fcd"
> fcdsl2 841124 0
> capi 17921 0
> capifs 6217 2 capi
> kernelcapi 47201 2 fcdsl2,capi
korrekt
> >capiinfo
> capi not installed - No such device or address (6)
hast Du zu diesem Zeitpunkt ein /dev/capi20?
ls /dev/capi*
/dev/capi20
/dev/capi:
(/dev/capi ist leer und wird erst bevölkert, wenn eine Verbindung
besteht.)
>
> rpm -qa | grep fcp
> fcpci-03.11.07-7.rhfc4.at
> fcpci-kmdl-2.6.13-1.1526_FC4-03.11.07-7.rhfc4.at
Moment, Moment! Du hast eine Fritzcard DSL und eine Fritzcard PCI? In
eimem Rechner?
Abgesehen davon ist das nicht der aktuelle Kernel, 1532 ist aktuell. Für
den hat Axel aber noch keine Kernelmodule, für die DSL-Karte sowieso
nicht. Also ist Eigenbau angesagt.
>
> und
>
> fcdsl2-suse93-3.11-07.tar.gz ist installiert
>
Wieso "und"? Das war ein "entweder ... oder", nicht beides!
> Gruß
> Bruno
>
Alles unklar? ;-)
Christoph
--
Fedora-de-list mailing list
Fedora-de-list(a)redhat.com
https://www.redhat.com/mailman/listinfo/fedora-de-list