X crashes when using a new monitor
by Benjamin Jiang
Hi, all,
I installed a fresh copy of FC3 into my Dad's machine and everything
worked fine. However, when I brought the machine to my Dad's place and
plugged in his monitor (Acer 7154e), X crashes no matter what. I tried
config xorg.conf with the correct HorizSync and VertRefresh, but it
didn't even make any difference.
Then I tried the extreme solution: I replaced the HDD with a new HDD and
installed a fresh copy FC3 with my Dad's monitor plugged in while
installation. Everything worked fine again and I got graphics interface.
I then grabbed the working xorg.conf and swapped the HDDs. After I
booted into the previous installed FC3, I replaced the xorg.conf with
the working xorg.conf. It still didn't make any difference!
I am a little confused. Is there some other file I need to change except
for /etc/X11/xorg.conf? Is there any special module I need to load?
I know I could just re-install FC3 into my Dad's HDD. I am just curious
to see what's wrong here.
Here's the setup:
AMD K6 350Mhz;
196MB RAM
Trident Blade3D 8MB video card
Thanks in advance!
Ben.
Here comes the log file: /var/log/Xorg.0.log:
---------------------------------------------------------------------------------
X Window System Version 6.8.1
Release Date: 17 September 2004
X Protocol Version 11, Revision 0, Release 6.8.1
Build Operating System: Linux 2.4.21-14.ELsmp i686 [ELF]
Current Operating System: Linux fallsview 2.6.9-1.667 #1 Tue Nov 2
14:41:31 EST 2004 i586
Build Date: 20 October 2004
Build Host: tweety.build.redhat.com
Before reporting problems, check http://wiki.X.Org
to make sure that you have the latest version.
Module Loader present
OS Kernel: Linux version 2.6.9-1.667 (bhcompile(a)tweety.build.redhat.com)
(gcc version 3.4.2 20041017 (Red Hat 3.4.2-6.fc3)) #1 Tue Nov 2 14:41:31
EST 2004
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Sat Jan 1 02:56:07 2000
(++) Using config file: "xorg.conf.new"
(==) ServerLayout "Default Layout"
(**) |-->Screen "Screen0" (0)
(**) | |-->Monitor "Monitor0"
(**) | |-->Device "Videocard0"
(**) |-->Input Device "Mouse0"
(**) |-->Input Device "Keyboard0"
(**) FontPath set to "unix/:7100"
(**) RgbPath set to "/usr/X11R6/lib/X11/rgb"
(==) ModulePath set to "/usr/X11R6/lib/modules"
(WW) Open APM failed (/dev/apm_bios) (No such file or directory)
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.2
X.Org Video Driver: 0.7
X.Org XInput driver : 0.4
X.Org Server Extension : 0.2
X.Org Font Renderer : 0.4
(II) Loader running on linux
(II) LoadModule: "bitmap"
(II) Loading /usr/X11R6/lib/modules/fonts/libbitmap.a
(II) Module bitmap: vendor="X.Org Foundation"
compiled for 6.8.1, module version = 1.0.0
Module class: X.Org Font Renderer
ABI class: X.Org Font Renderer, version 0.4
(II) Loading font Bitmap
(II) LoadModule: "pcidata"
(II) Loading /usr/X11R6/lib/modules/libpcidata.a
(II) Module pcidata: vendor="X.Org Foundation"
compiled for 6.8.1, module version = 1.0.0
ABI class: X.Org Video Driver, version 0.7
(--) using VT number 7
(II) PCI: Probing config type using method 1
(II) PCI: Config type is 1
(II) PCI: stages = 0x03, oldVal1 = 0x00000000, mode1Res1 = 0x80000000
(II) PCI: PCI scan (all values are in hex)
(II) PCI: 00:00:0: chip 1106,0598 card 0000,0000 rev 04 class 06,00,00
hdr 00
(II) PCI: 00:01:0: chip 1106,8598 card 0000,0000 rev 00 class 06,04,00
hdr 01
(II) PCI: 00:07:0: chip 1106,0686 card 1106,0000 rev 22 class 06,01,00
hdr 80
(II) PCI: 00:07:1: chip 1106,0571 card 0000,0000 rev 10 class 01,01,8a
hdr 00
(II) PCI: 00:07:2: chip 1106,3038 card 0925,1234 rev 10 class 0c,03,00
hdr 00
(II) PCI: 00:07:3: chip 1106,3038 card 0925,1234 rev 10 class 0c,03,00
hdr 00
(II) PCI: 00:07:4: chip 1106,3057 card 0000,0000 rev 30 class 06,00,00
hdr 00
(II) PCI: 00:08:0: chip 122d,50dc card 122d,8000 rev 10 class 04,01,00
hdr 00
(II) PCI: 00:0b:0: chip 10d9,0531 card 15e8,8110 rev 25 class 02,00,00
hdr 00
(II) PCI: 01:00:0: chip 1023,9880 card 1023,9880 rev 3a class 03,00,00
hdr 00
(II) PCI: End of PCI scan
(II) Host-to-PCI bridge:
(II) Bus 0: bridge is at (0:0:0), (0,0,1), BCTRL: 0x0008 (VGA_EN is set)
(II) Bus 0 I/O range:
[0] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[B]
(II) Bus 0 non-prefetchable memory range:
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B]
(II) Bus 0 prefetchable memory range:
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B]
(II) PCI-to-PCI bridge:
(II) Bus 1: bridge is at (0:1:0), (0,1,1), BCTRL: 0x000c (VGA_EN is set)
(II) Bus 1 non-prefetchable memory range:
[0] -1 0 0xd4000000 - 0xd7ffffff (0x4000000) MX[B]
(II) PCI-to-ISA bridge:
(II) Bus -1: bridge is at (0:7:0), (0,-1,-1), BCTRL: 0x0008 (VGA_EN is set)
(II) Host-to-PCI bridge:
(II) Bus -1: bridge is at (0:7:4), (-1,-1,1), BCTRL: 0x0008 (VGA_EN is set)
(II) Bus -1 I/O range:
[0] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[B]
(II) Bus -1 non-prefetchable memory range:
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B]
(II) Bus -1 prefetchable memory range:
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B]
(--) PCI:*(1:0:0) Trident Microsystems Blade 3D PCI/AGP rev 58, Mem @
0xd5800000/23, 0xd6000000/17, 0xd5000000/23
(II) Addressable bus resource ranges are
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B]
[1] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[B]
(II) OS-reported resource ranges:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[6] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
(II) PCI Memory resource overlap reduced 0xd0000000 from 0xd3ffffff to
0xcfffffff
(II) Active PCI resource ranges:
[0] -1 0 0xd9000000 - 0xd90000ff (0x100) MX[B]
[1] -1 0 0xd0000000 - 0xcfffffff (0x0) MX[B]O
[2] -1 0 0xd5000000 - 0xd57fffff (0x800000) MX[B](B)
[3] -1 0 0xd6000000 - 0xd601ffff (0x20000) MX[B](B)
[4] -1 0 0xd5800000 - 0xd5ffffff (0x800000) MX[B](B)
[5] -1 0 0x0000e000 - 0x0000e0ff (0x100) IX[B]
[6] -1 0 0x0000dc00 - 0x0000dc3f (0x40) IX[B]
[7] -1 0 0x0000d800 - 0x0000d807 (0x8) IX[B]
[8] -1 0 0x0000d400 - 0x0000d403 (0x4) IX[B]
[9] -1 0 0x0000d000 - 0x0000d007 (0x8) IX[B]
[10] -1 0 0x0000cc00 - 0x0000cc7f (0x80) IX[B]
[11] -1 0 0x0000c800 - 0x0000c81f (0x20) IX[B]
[12] -1 0 0x0000c400 - 0x0000c41f (0x20) IX[B]
[13] -1 0 0x0000c000 - 0x0000c00f (0x10) IX[B]
(II) Active PCI resource ranges after removing overlaps:
[0] -1 0 0xd9000000 - 0xd90000ff (0x100) MX[B]
[1] -1 0 0xd0000000 - 0xcfffffff (0x0) MX[B]O
[2] -1 0 0xd5000000 - 0xd57fffff (0x800000) MX[B](B)
[3] -1 0 0xd6000000 - 0xd601ffff (0x20000) MX[B](B)
[4] -1 0 0xd5800000 - 0xd5ffffff (0x800000) MX[B](B)
[5] -1 0 0x0000e000 - 0x0000e0ff (0x100) IX[B]
[6] -1 0 0x0000dc00 - 0x0000dc3f (0x40) IX[B]
[7] -1 0 0x0000d800 - 0x0000d807 (0x8) IX[B]
[8] -1 0 0x0000d400 - 0x0000d403 (0x4) IX[B]
[9] -1 0 0x0000d000 - 0x0000d007 (0x8) IX[B]
[10] -1 0 0x0000cc00 - 0x0000cc7f (0x80) IX[B]
[11] -1 0 0x0000c800 - 0x0000c81f (0x20) IX[B]
[12] -1 0 0x0000c400 - 0x0000c41f (0x20) IX[B]
[13] -1 0 0x0000c000 - 0x0000c00f (0x10) IX[B]
(II) OS-reported resource ranges after removing overlaps with PCI:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[6] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
(II) All system resource ranges:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0xd9000000 - 0xd90000ff (0x100) MX[B]
[6] -1 0 0xd0000000 - 0xcfffffff (0x0) MX[B]O
[7] -1 0 0xd5000000 - 0xd57fffff (0x800000) MX[B](B)
[8] -1 0 0xd6000000 - 0xd601ffff (0x20000) MX[B](B)
[9] -1 0 0xd5800000 - 0xd5ffffff (0x800000) MX[B](B)
[10] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[11] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
[12] -1 0 0x0000e000 - 0x0000e0ff (0x100) IX[B]
[13] -1 0 0x0000dc00 - 0x0000dc3f (0x40) IX[B]
[14] -1 0 0x0000d800 - 0x0000d807 (0x8) IX[B]
[15] -1 0 0x0000d400 - 0x0000d403 (0x4) IX[B]
[16] -1 0 0x0000d000 - 0x0000d007 (0x8) IX[B]
[17] -1 0 0x0000cc00 - 0x0000cc7f (0x80) IX[B]
[18] -1 0 0x0000c800 - 0x0000c81f (0x20) IX[B]
[19] -1 0 0x0000c400 - 0x0000c41f (0x20) IX[B]
[20] -1 0 0x0000c000 - 0x0000c00f (0x10) IX[B]
(II) LoadModule: "dbe"
(II) Loading /usr/X11R6/lib/modules/extensions/libdbe.a
(II) Module dbe: vendor="X.Org Foundation"
compiled for 6.8.1, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.2
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "extmod"
(II) Loading /usr/X11R6/lib/modules/extensions/libextmod.a
(II) Module extmod: vendor="X.Org Foundation"
compiled for 6.8.1, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.2
(II) Loading extension SHAPE
(II) Loading extension MIT-SUNDRY-NONSTANDARD
(II) Loading extension BIG-REQUESTS
(II) Loading extension SYNC
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XC-MISC
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-Misc
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension TOG-CUP
(II) Loading extension Extended-Visual-Information
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "fbdevhw"
(II) Loading /usr/X11R6/lib/modules/linux/libfbdevhw.a
(II) Module fbdevhw: vendor="X.Org Foundation"
compiled for 6.8.1, module version = 0.0.2
ABI class: X.Org Video Driver, version 0.7
(II) LoadModule: "glx"
(II) Loading /usr/X11R6/lib/modules/extensions/libglx.a
(II) Module glx: vendor="X.Org Foundation"
compiled for 6.8.1, module version = 1.0.0
ABI class: X.Org Server Extension, version 0.2
(II) Loading sub module "GLcore"
(II) LoadModule: "GLcore"
(II) Loading /usr/X11R6/lib/modules/extensions/libGLcore.a
(II) Module GLcore: vendor="X.Org Foundation"
compiled for 6.8.1, module version = 1.0.0
ABI class: X.Org Server Extension, version 0.2
(II) Loading extension GLX
(II) LoadModule: "record"
(II) Loading /usr/X11R6/lib/modules/extensions/librecord.a
(II) Module record: vendor="X.Org Foundation"
compiled for 6.8.1, module version = 1.13.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.2
(II) Loading extension RECORD
(II) LoadModule: "freetype"
(II) Loading /usr/X11R6/lib/modules/fonts/libfreetype.so
(II) Module freetype: vendor="X.Org Foundation & the After X-TT Project"
compiled for 6.8.1, module version = 2.1.0
Module class: X.Org Font Renderer
ABI class: X.Org Font Renderer, version 0.4
(II) Loading font FreeType
(II) LoadModule: "type1"
(II) Loading /usr/X11R6/lib/modules/fonts/libtype1.a
(II) Module type1: vendor="X.Org Foundation"
compiled for 6.8.1, module version = 1.0.2
Module class: X.Org Font Renderer
ABI class: X.Org Font Renderer, version 0.4
(II) Loading font Type1
(II) Loading font CID
(II) LoadModule: "dri"
(II) Loading /usr/X11R6/lib/modules/extensions/libdri.a
(II) Module dri: vendor="X.Org Foundation"
compiled for 6.8.1, module version = 1.0.0
ABI class: X.Org Server Extension, version 0.2
(II) Loading sub module "drm"
(II) LoadModule: "drm"
(II) Loading /usr/X11R6/lib/modules/linux/libdrm.a
(II) Module drm: vendor="X.Org Foundation"
compiled for 6.8.1, module version = 1.0.0
ABI class: X.Org Server Extension, version 0.2
(II) Loading extension XFree86-DRI
(II) LoadModule: "trident"
(II) Loading /usr/X11R6/lib/modules/drivers/trident_drv.o
(II) Module trident: vendor="X.Org Foundation"
compiled for 6.8.1, module version = 1.0.0
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 0.7
(II) LoadModule: "mouse"
(II) Loading /usr/X11R6/lib/modules/input/mouse_drv.o
(II) Module mouse: vendor="X.Org Foundation"
compiled for 6.8.1, module version = 1.0.0
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 0.4
(II) LoadModule: "kbd"
(II) Loading /usr/X11R6/lib/modules/input/kbd_drv.o
(II) Module kbd: vendor="X.Org Foundation"
compiled for 6.8.1, module version = 1.0.0
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 0.4
(II) TRIDENT: driver for Trident chipsets: tvga9000, tvga9000i, tvga8900c,
tvga8900d, tvga9200cxr, tgui9400cxi, cyber9320, cyber9388, cyber9397,
cyber9397dvd, cyber9520, cyber9525dvd, cyberblade/e4, tgui9420dgi,
tgui9440agi, tgui9660, tgui9680, providia9682, providia9685,
cyber9382, cyber9385, 3dimage975, 3dimage985, blade3d, cyberbladei7,
cyberbladei7d, cyberbladei1, cyberbladei1d, cyberbladeAi1,
cyberbladeAi1d, bladeXP, cyberbladeXPAi1, cyberbladeXP4
(II) Primary Device is: PCI 01:00:0
(--) Assigning device section with no busID to primary device
(--) Chipset blade3d found
(II) resource ranges after xf86ClaimFixedResources() call:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0xd9000000 - 0xd90000ff (0x100) MX[B]
[6] -1 0 0xd0000000 - 0xcfffffff (0x0) MX[B]O
[7] -1 0 0xd5000000 - 0xd57fffff (0x800000) MX[B](B)
[8] -1 0 0xd6000000 - 0xd601ffff (0x20000) MX[B](B)
[9] -1 0 0xd5800000 - 0xd5ffffff (0x800000) MX[B](B)
[10] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[11] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
[12] -1 0 0x0000e000 - 0x0000e0ff (0x100) IX[B]
[13] -1 0 0x0000dc00 - 0x0000dc3f (0x40) IX[B]
[14] -1 0 0x0000d800 - 0x0000d807 (0x8) IX[B]
[15] -1 0 0x0000d400 - 0x0000d403 (0x4) IX[B]
[16] -1 0 0x0000d000 - 0x0000d007 (0x8) IX[B]
[17] -1 0 0x0000cc00 - 0x0000cc7f (0x80) IX[B]
[18] -1 0 0x0000c800 - 0x0000c81f (0x20) IX[B]
[19] -1 0 0x0000c400 - 0x0000c41f (0x20) IX[B]
[20] -1 0 0x0000c000 - 0x0000c00f (0x10) IX[B]
(II) resource ranges after probing:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0xd9000000 - 0xd90000ff (0x100) MX[B]
[6] -1 0 0xd0000000 - 0xcfffffff (0x0) MX[B]O
[7] -1 0 0xd5000000 - 0xd57fffff (0x800000) MX[B](B)
[8] -1 0 0xd6000000 - 0xd601ffff (0x20000) MX[B](B)
[9] -1 0 0xd5800000 - 0xd5ffffff (0x800000) MX[B](B)
[10] 0 0 0x000a0000 - 0x000affff (0x10000) MS[B]
[11] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[B]
[12] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[B]
[13] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[14] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
[15] -1 0 0x0000e000 - 0x0000e0ff (0x100) IX[B]
[16] -1 0 0x0000dc00 - 0x0000dc3f (0x40) IX[B]
[17] -1 0 0x0000d800 - 0x0000d807 (0x8) IX[B]
[18] -1 0 0x0000d400 - 0x0000d403 (0x4) IX[B]
[19] -1 0 0x0000d000 - 0x0000d007 (0x8) IX[B]
[20] -1 0 0x0000cc00 - 0x0000cc7f (0x80) IX[B]
[21] -1 0 0x0000c800 - 0x0000c81f (0x20) IX[B]
[22] -1 0 0x0000c400 - 0x0000c41f (0x20) IX[B]
[23] -1 0 0x0000c000 - 0x0000c00f (0x10) IX[B]
[24] 0 0 0x000003b0 - 0x000003bb (0xc) IS[B]
[25] 0 0 0x000003c0 - 0x000003df (0x20) IS[B]
(II) Setting vga for screen 0.
(**) TRIDENT(0): Depth 16, (--) framebuffer bpp 16
(II) Loading sub module "vgahw"
(II) LoadModule: "vgahw"
(II) Loading /usr/X11R6/lib/modules/libvgahw.a
(II) Module vgahw: vendor="X.Org Foundation"
compiled for 6.8.1, module version = 0.1.0
ABI class: X.Org Video Driver, version 0.7
(II) TRIDENT(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset
is 0x0000
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Loading /usr/X11R6/lib/modules/libramdac.a
(II) Module ramdac: vendor="X.Org Foundation"
compiled for 6.8.1, module version = 0.1.0
ABI class: X.Org Video Driver, version 0.7
(==) TRIDENT(0): RGB weight 565
(==) TRIDENT(0): Default visual is TrueColor
(==) TRIDENT(0): Using gamma correction (1.0, 1.0, 1.0)
(==) TRIDENT(0): Linear framebuffer at 0xD5800000
(--) TRIDENT(0): IO registers at 0xD6000000
(II) Loading sub module "vbe"
(II) LoadModule: "vbe"
(II) Loading /usr/X11R6/lib/modules/libvbe.a
(II) Module vbe: vendor="X.Org Foundation"
compiled for 6.8.1, module version = 1.1.0
ABI class: X.Org Video Driver, version 0.7
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Loading /usr/X11R6/lib/modules/linux/libint10.a
(II) Module int10: vendor="X.Org Foundation"
compiled for 6.8.1, module version = 1.0.0
ABI class: X.Org Video Driver, version 0.7
(II) TRIDENT(0): initializing int10
(II) TRIDENT(0): Primary V_BIOS segment is: 0xc000
(II) TRIDENT(0): VESA BIOS detected
(II) TRIDENT(0): VESA VBE Version 2.0
(II) TRIDENT(0): VESA VBE Total Mem: 8192 kB
(II) TRIDENT(0): VESA VBE OEM: Trident Blade 3D
(II) TRIDENT(0): VESA VBE OEM Software Rev: 2.0
(II) TRIDENT(0): VESA VBE OEM Vendor: TRIDENT MICROSYSTEMS INC.
(II) TRIDENT(0): VESA VBE OEM Product: Blade 3D
(II) TRIDENT(0): VESA VBE OEM Product Rev: J 6.4 (38)
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Loading /usr/X11R6/lib/modules/libddc.a
(II) Module ddc: vendor="X.Org Foundation"
compiled for 6.8.1, module version = 1.0.0
ABI class: X.Org Video Driver, version 0.7
(II) TRIDENT(0): VESA VBE DDC supported
(II) TRIDENT(0): VESA VBE DDC Level 2
(II) TRIDENT(0): VESA VBE DDC transfer in appr. 1 sec.
(II) TRIDENT(0): VESA VBE DDC read successfully
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Reloading /usr/X11R6/lib/modules/libddc.a
(II) TRIDENT(0): Manufacturer: API Model: 4536 Serial#: 924
(II) TRIDENT(0): Year: 1997 Week: 26
(II) TRIDENT(0): EDID Version: 1.2
(II) TRIDENT(0): Analog Display Input, Input Voltage Level: 0.700/0.300 V
(II) TRIDENT(0): Sync: Separate
(II) TRIDENT(0): Max H-Image Size [cm]: horiz.: 27 vert.: 20
(II) TRIDENT(0): Gamma: 2.66
(II) TRIDENT(0): DPMS capabilities: StandBy Suspend Off; RGB/Color Display
(II) TRIDENT(0): redX: 0.625 redY: 0.340 greenX: 0.284 greenY: 0.600
(II) TRIDENT(0): blueX: 0.149 blueY: 0.064 whiteX: 0.280 whiteY: 0.311
(II) TRIDENT(0): Supported VESA Video Modes:
(II) TRIDENT(0): 720x400@70Hz
(II) TRIDENT(0): 640x480@60Hz
(II) TRIDENT(0): 640x480@72Hz
(II) TRIDENT(0): 640x480@75Hz
(II) TRIDENT(0): 800x600@60Hz
(II) TRIDENT(0): 800x600@72Hz
(II) TRIDENT(0): 800x600@75Hz
(II) TRIDENT(0): 1024x768@60Hz
(II) TRIDENT(0): Manufacturer's mask: 21
(--) TRIDENT(0): Revision is 58
(--) TRIDENT(0): Found Blade3D chip
(--) TRIDENT(0): RAM type is SDRAM
(--) TRIDENT(0): Using HW cursor
(--) TRIDENT(0): VideoRAM: 8192 kByte
(--) TRIDENT(0): Memory Clock is 109.77 MHz
(==) TRIDENT(0): Min pixel clock is 12 MHz
(--) TRIDENT(0): Max pixel clock is 230 MHz
(II) TRIDENT(0): Monitor0: Using hsync range of 31.00-60.00 kHz
(II) TRIDENT(0): Monitor0: Using vrefresh range of 55.00-90.00 Hz
(II) TRIDENT(0): Clock range: 12.00 to 230.00 MHz
(II) TRIDENT(0): Not using default mode "320x175" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "320x200" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "360x200" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "320x240" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "320x240" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "320x240" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "320x240" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "400x300" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "400x300" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "400x300" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "400x300" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "400x300" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "512x384" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "512x384" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "512x384" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "512x384" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "1024x768" (hsync out of range)
(II) TRIDENT(0): Not using default mode "512x384" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "1152x864" (hsync out of range)
(II) TRIDENT(0): Not using default mode "576x432" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "640x480" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "1280x960" (hsync out of range)
(II) TRIDENT(0): Not using default mode "640x480" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "1280x1024" (hsync out of range)
(II) TRIDENT(0): Not using default mode "640x512" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "1280x1024" (hsync out of range)
(II) TRIDENT(0): Not using default mode "640x512" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "1280x1024" (hsync out of range)
(II) TRIDENT(0): Not using default mode "640x512" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "1600x1200" (hsync out of range)
(II) TRIDENT(0): Not using default mode "800x600" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "1600x1200" (hsync out of range)
(II) TRIDENT(0): Not using default mode "800x600" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "1600x1200" (hsync out of range)
(II) TRIDENT(0): Not using default mode "800x600" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "1600x1200" (hsync out of range)
(II) TRIDENT(0): Not using default mode "800x600" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "1600x1200" (hsync out of range)
(II) TRIDENT(0): Not using default mode "800x600" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "1792x1344" (hsync out of range)
(II) TRIDENT(0): Not using default mode "896x672" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "1792x1344" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "896x672" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "1856x1392" (hsync out of range)
(II) TRIDENT(0): Not using default mode "928x696" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "1856x1392" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "928x696" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "1920x1440" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "960x720" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "1920x1440" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "960x720" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "416x312" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "576x384" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "1152x864" (hsync out of range)
(II) TRIDENT(0): Not using default mode "576x432" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "1400x1050" (hsync out of range)
(II) TRIDENT(0): Not using default mode "700x525" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "1400x1050" (hsync out of range)
(II) TRIDENT(0): Not using default mode "700x525" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "1400x1050" (hsync out of range)
(II) TRIDENT(0): Not using default mode "700x525" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "1400x1050" (hsync out of range)
(II) TRIDENT(0): Not using default mode "700x525" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "1600x1024" (hsync out of range)
(II) TRIDENT(0): Not using default mode "800x512" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "1920x1200" (hsync out of range)
(II) TRIDENT(0): Not using default mode "960x600" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "1920x1440" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "960x720" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "2048x1536" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "1024x768" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "2048x1536" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "1024x768" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "2048x1536" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "1024x768" (bad mode
clock/interlace/doublescan)
(II) TRIDENT(0): Not using default mode "1280x960" (width too large for
virtual size)
(II) TRIDENT(0): Not using default mode "1152x768" (width too large for
virtual size)
(II) TRIDENT(0): Not using default mode "1024x768" (width too large for
virtual size)
(II) TRIDENT(0): Not using default mode "1024x768" (width too large for
virtual size)
(II) TRIDENT(0): Not using default mode "1024x768" (width too large for
virtual size)
(II) TRIDENT(0): Not using default mode "1024x768" (width too large for
virtual size)
(II) TRIDENT(0): Not using default mode "832x624" (width too large for
virtual size)
(--) TRIDENT(0): Virtual size is 800x600 (pitch 800)
(**) TRIDENT(0): *Default mode "800x600": 56.3 MHz, 53.7 kHz, 85.1 Hz
(II) TRIDENT(0): Modeline "800x600" 56.30 800 832 896 1048 600 601
604 631 +hsync +vsync
(**) TRIDENT(0): *Default mode "640x480": 36.0 MHz, 43.3 kHz, 85.0 Hz
(II) TRIDENT(0): Modeline "640x480" 36.00 640 696 752 832 480 481
484 509 -hsync -vsync
(**) TRIDENT(0): Default mode "800x600": 49.5 MHz, 46.9 kHz, 75.0 Hz
(II) TRIDENT(0): Modeline "800x600" 49.50 800 816 896 1056 600 601
604 625 +hsync +vsync
(**) TRIDENT(0): Default mode "800x600": 50.0 MHz, 48.1 kHz, 72.2 Hz
(II) TRIDENT(0): Modeline "800x600" 50.00 800 856 976 1040 600 637
643 666 +hsync +vsync
(**) TRIDENT(0): Default mode "800x600": 40.0 MHz, 37.9 kHz, 60.3 Hz
(II) TRIDENT(0): Modeline "800x600" 40.00 800 840 968 1056 600 601
605 628 +hsync +vsync
(**) TRIDENT(0): Default mode "800x600": 36.0 MHz, 35.2 kHz, 56.2 Hz
(II) TRIDENT(0): Modeline "800x600" 36.00 800 824 896 1024 600 601
603 625 +hsync +vsync
(**) TRIDENT(0): Default mode "640x480": 31.5 MHz, 37.5 kHz, 75.0 Hz
(II) TRIDENT(0): Modeline "640x480" 31.50 640 656 720 840 480 481
484 500 -hsync -vsync
(**) TRIDENT(0): Default mode "640x480": 31.5 MHz, 37.9 kHz, 72.8 Hz
(II) TRIDENT(0): Modeline "640x480" 31.50 640 664 704 832 480 489
491 520 -hsync -vsync
(**) TRIDENT(0): Default mode "640x480": 25.2 MHz, 31.5 kHz, 60.0 Hz
(II) TRIDENT(0): Modeline "640x480" 25.20 640 656 752 800 480 490
492 525 -hsync -vsync
(**) TRIDENT(0): Default mode "720x400": 35.5 MHz, 37.9 kHz, 85.0 Hz
(II) TRIDENT(0): Modeline "720x400" 35.50 720 756 828 936 400 401
404 446 -hsync +vsync
(**) TRIDENT(0): Default mode "640x400": 31.5 MHz, 37.9 kHz, 85.1 Hz
(II) TRIDENT(0): Modeline "640x400" 31.50 640 672 736 832 400 401
404 445 -hsync +vsync
(**) TRIDENT(0): Default mode "640x350": 31.5 MHz, 37.9 kHz, 85.1 Hz
(II) TRIDENT(0): Modeline "640x350" 31.50 640 672 736 832 350 382
385 445 +hsync -vsync
(**) TRIDENT(0): Display dimensions: (270, 200) mm
(**) TRIDENT(0): DPI set to (75, 76)
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/X11R6/lib/modules/libfb.a
(II) Module fb: vendor="X.Org Foundation"
compiled for 6.8.1, module version = 1.0.0
ABI class: X.Org ANSI C Emulation, version 0.2
(II) Loading sub module "i2c"
(II) LoadModule: "i2c"
(II) Loading /usr/X11R6/lib/modules/libi2c.a
(II) Module i2c: vendor="X.Org Foundation"
compiled for 6.8.1, module version = 1.2.0
ABI class: X.Org Video Driver, version 0.7
(II) Loading sub module "xaa"
(II) LoadModule: "xaa"
(II) Loading /usr/X11R6/lib/modules/libxaa.a
(II) Module xaa: vendor="X.Org Foundation"
compiled for 6.8.1, module version = 1.2.0
ABI class: X.Org Video Driver, version 0.7
*** If unresolved symbols were reported above, they might not
*** be the reason for the server aborting.
Fatal server error:
Caught signal 11. Server aborting
Please consult the The X.Org Foundation support
at http://wiki.X.Org
for help.
Please also check the log file at "/var/log/Xorg.0.log" for additional
information.
19 years, 1 month
FC3 annoyances (blanking and blanking)
by Ofer Nave
Hello! I'm new to Fedora... just installed FC3. There are two
annoyances that I haven't found a way around, and I was hoping to get
help here.
1) I can't find a way to stop the screen from blanking after a while. I
tried the screensaver settings, the power settings, and xset s off...
nothing has worked so far.
2) I used to use SecureCRT to ssh into linux boxes for development, and
when I used man or less, the last screen would remain visible after
pressing 'q' to return to the prompt. Now that I'm using X, it
disappears when I quit. I've tried xterm, konsole, and gnome term - all
have the same behavior.
Thanks!
-ofer
19 years, 1 month
RE: Being denied my own files!
by marc.miller＠amd.com
In order to delete the file, you must:
* have write access to the file
* have write access to the directory
* the sTicky bit (chmod +t) must not be set on the directory (sTicky is
rare)
-----Original Message-----
From: fedora-desktop-list-bounces(a)redhat.com
[mailto:fedora-desktop-list-bounces@redhat.com] On Behalf Of Dotan Cohen
Sent: Thursday, March 10, 2005 5:09 PM
To: fedora-desktop-list(a)redhat.com
Subject: Being denied my own files!
When trying to delete a file in my /home/dotancohen directory (and
logged in as dotancohen) I get:
Access denied to /home/dotancohen/ankush.jpg.
In rightClick-> Properties-> Permissions I saw that Owner can read and
write, Group can read, and Others can read. So I changed the
permissions so that all the groups say read & write, but still I
cannot delete the file. No other application is accessing the file.
I'm using Konqueror in KDE on FC3. Thanks in advance.
Dotan Cohen
http://English-Lyrics.com
http://Song-Lyriks.com
--
Fedora-desktop-list mailing list
Fedora-desktop-list(a)redhat.com
http://www.redhat.com/mailman/listinfo/fedora-desktop-list
19 years, 1 month
RE: FC2 grub defaults to oldest kernel
by Matthew Page
That all depends... If the kernel you want to run is listed first, then
the answer to your question is yes.
> -----Original Message-----
> From: fedora-desktop-list-bounces(a)redhat.com
[mailto:fedora-desktop-list-
> bounces(a)redhat.com] On Behalf Of beartooth
> Sent: Thursday, March 10, 2005 11:15 AM
> To: fedora-desktop-list(a)redhat.com
> Subject: Re: FC2 grub defaults to oldest kernel
>
> On Wed, 09 Mar 2005 18:07:26 +0100, Nils Breunese wrote:
>
> >> > If you don't mind a little file editing, you can change the
default
> in
> >> > your /etc/grub.conf
> >>
> >> OK, the first line not commented out says "default=2" Does that
mean it
> >> will always be the second one down the list of however many, or
> something
> >> else? Can I simply change the 2 to a 1?
> >
> > It means it will always be the third down the list of however many.
The
> > count starts at 0.
>
> Aha. I couldn't tell whether it was a sneakin' hunch or a faint
memory,
> but I had a distinct intimation of some sort of lurking gotcha there
> somewhere. So if I want FC2 to behave as I'm accustomed to things
redhat
> doing, I should just change the 2 to a zero -- right? That's it?
>
> --
> Beartooth Implacable, Linux Evangelist & Gadfly
> neo-redneck, curmudgeonly codger with FC1&2, YDL4
> Pine 4.62, Pan 0.14.2; Privoxy 3.0.1; Opera 7.54, Firefox 1.0
> Bear in mind that I have little idea what I am talking about.
>
>
> --
> Fedora-desktop-list mailing list
> Fedora-desktop-list(a)redhat.com
> http://www.redhat.com/mailman/listinfo/fedora-desktop-list
>
>
> BEGIN-ANTISPAM-VOTING-LINKS
> ------------------------------------------------------
> Teach CanIt if this mail (ID 1945175) is spam:
> Spam:
> http://canit.ciri.com/canit/b.php?c=s&i=1945175&m=f59a2571da95
> Not spam:
> http://canit.ciri.com/canit/b.php?c=n&i=1945175&m=f59a2571da95
> Forget vote:
> http://canit.ciri.com/canit/b.php?c=f&i=1945175&m=f59a2571da95
> ------------------------------------------------------
> END-ANTISPAM-VOTING-LINKS
19 years, 1 month
Being denied my own files!
by Dotan Cohen
When trying to delete a file in my /home/dotancohen directory (and
logged in as dotancohen) I get:
Access denied to /home/dotancohen/ankush.jpg.
In rightClick-> Properties-> Permissions I saw that Owner can read and
write, Group can read, and Others can read. So I changed the
permissions so that all the groups say read & write, but still I
cannot delete the file. No other application is accessing the file.
I'm using Konqueror in KDE on FC3. Thanks in advance.
Dotan Cohen
http://English-Lyrics.com
http://Song-Lyriks.com
19 years, 1 month
RE: FC2 grub defaults to oldest kernel
by Matthew Page
If you don't mind a little file editing, you can change the default in
your /etc/grub.conf
> -----Original Message-----
> From: fedora-desktop-list-bounces(a)redhat.com
[mailto:fedora-desktop-list-
> bounces(a)redhat.com] On Behalf Of beartooth
> Sent: Tuesday, March 08, 2005 11:14 AM
> To: fedora-desktop-list(a)redhat.com
> Subject: Re: FC2 grub defaults to oldest kernel
>
> On Tue, 08 Mar 2005 12:07:52 -0500, Matthew Miller wrote:
>
> > On Tue, Mar 08, 2005 at 11:19:31AM -0500, beartooth wrote:
> >> My past experience has been that grub automatically makes each new
> kernel
> >> the default boot; but on my FC2 machine the default is the oldest
one.
> Is
> >> there a reason for this? Or should I fix it? And if so, how?
> >
> > This is addressed in FC3 -- look at /etc/sysconfig/kernel.
>
> I tried FC3, weeks ago -- and didn't like it. Iirc that tale of woe
was
> here; anyway, I'm not about to try again for another year or two. And
> during that time I'll stick to FC2 -- if not go back to FC1. So what
> should I do with FC2??
>
> --
> Beartooth Implacable, Linux Evangelist & Gadfly
> neo-redneck, curmudgeonly codger with FC1 & YDL 4.0
> Pine 4.61, Pan 0.14.2; Privoxy 3.0.1; Opera 7.54, Firefox 1.0
> Bear in mind that I have little idea what I am talking about.
>
>
> --
> Fedora-desktop-list mailing list
> Fedora-desktop-list(a)redhat.com
> http://www.redhat.com/mailman/listinfo/fedora-desktop-list
>
>
> BEGIN-ANTISPAM-VOTING-LINKS
> ------------------------------------------------------
> Teach CanIt if this mail (ID 1934675) is spam:
> Spam:
> http://canit.ciri.com/canit/b.php?c=s&i=1934675&m=172ba00e46ce
> Not spam:
> http://canit.ciri.com/canit/b.php?c=n&i=1934675&m=172ba00e46ce
> Forget vote:
> http://canit.ciri.com/canit/b.php?c=f&i=1934675&m=172ba00e46ce
> ------------------------------------------------------
> END-ANTISPAM-VOTING-LINKS
19 years, 1 month
Some more OOo 2 questions.
by Gain Paolo Mureddu
I was following the OOo 2's locale and language packs discussion,
however I may lack some background here... And hence I have some questions:
1.- Are the Fedora folks involved in any way on OOo 2 development?
2.- Is there a test build for Fedora or something? Or the only way to
get OOo 2 Beta is from the project's official site only?
2bis.- In the event you get the packages from openoffice.org's site,
will installing them remove/overwrite OOo 1.1.3?
3.- Once OOo 2 is released, most probably Core 4 will include it, but
will be also made available for previous versions of Fedora by means of
the Extras repository? (this would actually be cool!)
Thanks y'all!
19 years, 1 month
locales in OpenOffice.org 2.0pre
by Bill Nottingham
Currently we ship the following localizations in OOo 2.0pre that
don't correspond to any glibc supported locale:
- eo
- kn-IN
- ns
- tn
- zu
Any reason to keep them?
Bill
19 years, 1 month
FC2 grub defaults to oldest kernel
by Beartooth
My past experience has been that grub automatically makes each new kernel
the default boot; but on my FC2 machine the default is the oldest one. Is
there a reason for this? Or should I fix it? And if so, how?
--
Beartooth Implacable, Linux Evangelist & Gadfly
neo-redneck, curmudgeonly codger with FC1&2, YDL4
Pine 4.62, Pan 0.14.2; Privoxy 3.0.1; Opera 7.54, Firefox 1.0
Bear in mind that I have little idea what I am talking about.
19 years, 1 month
