ata_piix/libata - dma for ide dvd question/status
by Jarosław Górny
Hi,
First, I'd like to say that I know that the question is not laptop specific,
not even FC-specific, but I think there's a chance that someone can at least
show me a right place to investigate further.
To the point:
I use FC5 on Dell Inspiron E1505 (vel 6400) with ICH7 chipset. It has SATA
harddisk and IDE DVD drive[1].
CD/DVD burning is slow as well as playing DVDs, because DMA for this drive is
turned off and it's impossible to enable it[2].
There are some tips (rather old, for kernels<2.6.13 AFAIK) around. Eg.
adding 'hdc=noprobe' or 'combined_mode=libata' to kernel boot command line -
that makes dvd drive to work in scsi-emulation mode.
And this is where my questions go:
1. What is the current status of ata_piix/libata, is there a work going on to
make it possible to enable DMA for IDE drive in native mode?
2. If scsi-emulation is still required to get reasonable transfers, what is
the right way to set it up?
regards,
[1]
00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) Serial ATA
Storage Controller IDE (rev 01)
[2]
<code>
[root@moonstone ~]# hdparm -d1 /dev/hdc
/dev/hdc:
setting using_dma to 1 (on)
HDIO_SET_DMA failed: Operation not permitted
using_dma = 0 (off)
</code>
--
Jaroslaw Gorny
17 years, 5 months
Speedstep doesn't work on Centrino notebooks for Fedora Core 6
by Julian Yap
Hi,
I have a Dell Inspiron 6000 notebook.
I'm running a Intel(R) Pentium(R) M processor 1.73GHz CPU.
I noticed during boot up, I get an error that can be reproduced when I try
and start up the cpuspeed service.
# /etc/init.d/cpuspeed start
FATAL: Error inserting acpi_cpufreq (/lib/modules/2.6.18-1.2798.fc6
/kernel/arch/i386/kernel/cpu/cpufreq/acpi-cpufreq.ko): No such device
I've noticed that Fedora doesn't include the speedstep-centrino.ko module.
Normally it would be located in:
/lib/modules/2.6.18-1.2798.fc6/kernel/arch/i386/kernel/cpu/cpufreq/
Would this be the issue?
There's a few bugs in Bugzilla if you search for acpi_cpufreq in Summary.
This bug prevents the CPU from stepping down the lower speed (thus running
all the time at the full speed).
Regards,
Julian
17 years, 5 months
Re: Speedstep doesn't work on Centrino notebooks for Fedora Core 6
by Laszlo BERES
Dave Jones wrote:
> When was the last time this worked for you?
I have the same issue on a Fujitsu-Siemens Lifebook E4010 with Pentium-M
1.4 processor. Cpuspeed worked perfectly since the first FC5 kernel and
now with 2.6.18-1.2200.fc5 too.
FC6 broke this success :(
--
BÉRES László RHCE
senior IT engineer, trainer
17 years, 5 months
Laptop improvement
by Jindrich Novy
Hi,
I'm forwarding you an email from Martin Sebesta related to IBM T60
laptop issue:
> > I am using IBM T60 with FC5. When i switch to batteries, my fan
starts
> > > to operate on higher speed (i hear it) than usual, draining my battery
> > > totally empty in less than 2 hours.
> > > As i have installed Windows with VMware with FC 5 in it on the same
> > > maschine, i tried to work in FC on Windows. The battery lasted for more
> > > than 5 hours.
> > > In each case the battery was fully loaded on the beginning.
> > >
> > > Perhaps a tip for power-management improvement...
Any help is appreciated. I have to mention I see similar behavior
of my HP laptop when it's resurrected from software suspend sometimes
even on FC6. CPU load is at 100% immediately after waking the laptop up.
Did anyone from you experience similar problems? Is there known
any workaround?
Thanks,
Jindrich
17 years, 6 months
Full screen video on Thinkpad T41p
by Joe Desbonnet
Shortly after installing FC5 on my T41p (ATI FireGL) I was able to get
mplayer to play full screen video (pressing the 'f' button). Watching
video was one of the last few reasons I had for rebooting into Windows
so this was cool.
I recall a flame war on the devel list about some upgrade (I think it
was to X.org) which was going to break ATI drivers. I signed off the
list at that point.
Sure enough, shortly thereafter a "yum upgrade" degraded my machine
so that full screen video nologer worked (I now just get a huge black
border around the tiny video window when I press 'f' in mplayer).
I don't know enough about X.org, Xv, mplayer etc to troubleshoot this
problem. I don't even know what info I should post here to help
diagnose the problem.
Any troubleshooting tips would be greatly appreciated.
Joe.
17 years, 6 months
(no subject)
by g sinuco
Hello!!
I had installed the last version of Ferora Core in a HP pavillon dv6000 (laptop) and the x system doesn't work. When the first sesion ends his loading i recieve as result a black screen and I can't do anything I gues the driver is not working and i have the lastest driver from NVIDIA but I don't know how to install it because i don't have access to a text mode. My video card is a NVIDIA GeForce 7200 Go.
I installed too the last version os Slamd64, a slackware version for 64 bits, and I installed the driver provide for NVIDIA but i have a very unstable behaviour: The X systems runs but few minutes later craks and nothing works.
Please help me.
Germ'an Sinuco
---------------------------------
Do You Yahoo!? La mejor conexión a Internet y 2GB extra a tu correo por $100 al mes. http://net.yahoo.com.mx
17 years, 6 months
FC6 and laptops -- comments anyone?
by Joe Desbonnet
Any comments on FC6 and laptops based on the last test release? I
haven't had time to experiment myself.
I have mixed feelings about FC5. It started off fine and progressively
got worse (Thinkpad T41p compatibility wise) as the updates were
applied.
Joe.
17 years, 6 months
