Openapc & siemens
by Mansour Ahmadi
Dear Friend,
Does Openapc support siemens ?
Thank you.
7 years, 10 months
Re: Connecting CT EC1000 with RTC4 libraries
by Francesco Perrucci
Jim,
I think I found the solution. In the configuration wizard it's possible to
convert the correction table from .xml to a scanlab file.
So I'll try as possible and then I'll write you if it's ok!!
Maybe I need an USB connection to the EC1000, but the vendor never gives me
the right datasheet for the I/O module. So i'm writing him to ask about
this.
Thank you very much for your rapid answers.
Francesco
2014-11-19 7:30 GMT+01:00 Jim Hart <openapc(a)gmail.com>:
> Francesco,
>
> the .hex file is not really needed when you use UAPI-emulation, but you
> have to
> set it to satisfy the RTC4-plug-in. For the correction file situation is a
> bit
> different, I think you have to set it. But I don't know if you have to
> specify
> the .xml file or a .ctb file converted out of the .xml file from CTI. May
> be
> CTIs manual gives some information here?
>
> Jim
>
>
> > On 18 November 2014 at 21:27 Francesco Perrucci <
> francesco.perrucci(a)polito.it>
> > wrote:
> >
> >
> > Dear Jim,
> >
> > thank you for the rapid answer.
> >
> >
> > Now I understand that RTC4 work as a conversion for EC1000.
> > But I've still difficulties to make the connection with this card.
> >
> > First I would ask to you if it's needed an USB connection. Because now I
> > can only connect the EC1000 through wi-fi or ethernet connection. Looking
> > the electronic board I find a usb pin, so I think I could use it if
> > necessary.
> >
> > I've already the RTC4DL file by the installation package of Cambridge
> > Technology. I put this file into the Windows/SysWOW64 and then I follow
> the
> > instruction of RTC emulation loader ( CTI installation package ) as you
> can
> > see in the attached pdf
> >
> > Then into BeamConstruct I select RTC4 in scanner controller settings and
> > then into the configuration panel the sofware ask me for the correction
> and
> > firmware files.
> >
> > So there's the problem. Into the zip dowloaded through your link, I can
> > find the ctb (correction) and the hex (firmware) files, but I think they
> > are related to Scanlab RTC4 controller.
> >
> > I need this file for my EC1000 controller, it is right? Into the CTI
> > installation directory I've only .xml file both for correction than for
> > firmware files, so i can't select them.
> >
> > Hope you can help me!!
> >
> > Thank you very much
> > Francesco
> >
> >
> >
> > 2014-11-18 6:59 GMT+01:00 Jim Hart <openapc(a)gmail.com>:
> >
> > > Francesco,
> > >
> > > let me answer this in reverse order:
> > >
> > > > In addition to this, into the scanner section of the project
> proprieties
> > > of
> > > > BeamConstruct I can't find the EC1000 entry. It seems that the
> software
> > > > doesn't support it.
> > >
> > > When you are using CTIs RTC emulation you needto select RTC4 in scanner
> > > controller settings. For BeamConstruct it acts like a RTC4, conversion
> to
> > > EC1000
> > > is done by the emulation layer.
> > >
> > > > There's a software called RTC emulation loader that ask me to browse
> into
> > > > the application's folder that contains the RTC4DLL.dll in order to
> > > replace
> > > > it, but i can't find this file into the OpenAPC folders.
> > >
> > > RTC4DL is a 3rd party software and therefore not delivered with OpenAPC
> > > package.
> > > You can download it at
> > >
> http://www.scanlab.de/en/-/products/control_boards/RTC_PC_interface#21065
> > >
> > > I'd recommend to put RTC4DLL somewhere into Windows/System32 or
> > > Windows/SysWOW64
> > > (depending if you are using a 32 or 64 bit Windows).
> > >
> > > Jim
> > >
> > >
> > >
> > > > _______________________________________________
> > > > openapc mailing list
> > > > openapc(a)lists.fedorahosted.org
> > > > https://lists.fedorahosted.org/mailman/listinfo/openapc
> > >
> > >
> > > --
> > > Kind regards
> > >
> > > Jim Hart
> > >
> > > http://www.lasermarkingsoftware.com
> > > http://www.openapc.com
> > >
> > > Follow us at Twitter: https://twitter.com/#!/openapc
> > > _______________________________________________
> > > openapc mailing list
> > > openapc(a)lists.fedorahosted.org
> > > https://lists.fedorahosted.org/mailman/listinfo/openapc
> > >
>
>
> --
> Kind regards
>
> Jim Hart
>
> http://www.lasermarkingsoftware.com
> http://www.openapc.com
>
> Follow us at Twitter: https://twitter.com/#!/openapc
>
9 years, 4 months
Connecting CT EC1000 with RTC4 libraries
by Francesco Perrucci
Hello,
I'm trying to connect my CT EC1000 ( find it into the supported hardware
page ) with the RTC library, but i'm not able to do it.
I found this into the EC1000 RTC Emulation readme file:
*The emulation is made possible by substituting the RTC4DLL.dll file in
your application directory with a series of DLLs including a CTI version of
RTC4DLL.dll. This collection of DLLs enable the translation of your
application’s RTC commands intoEC1000 native commands. *
There's a software called RTC emulation loader that ask me to browse into
the application's folder that contains the RTC4DLL.dll in order to replace
it, but i can't find this file into the OpenAPC folders.
In addition to this, into the scanner section of the project proprieties of
BeamConstruct I can't find the EC1000 entry. It seems that the software
doesn't support it.
Someone can help me? I'm not an expert.
Francesco
9 years, 5 months
