I have recently begun to use again gnome session and I have reinstalled
I see that nautilus depends on tracker and so the reinstall put in tracker
and its things
And this morning in my F28 system with SSD disk (I don't imagine on a
normal sata based environment) I had to kill tracker-extract and
tacker-miner processes because they hogged my cpu for several minutes..
Searching with google I found different info about disabling (or at least
calm down) tracker, but they all seem not updated, in the sense that
several commands/services are not present in my f28 environment.
Any pointer about configuring and/or disabling it?
Thanks in advance,
Mounting an internally installed disk on a laptop spins up all
disks connected to this machine via USB. And I try to prevent these
externally connected disks to spin up.
The behaviour, IIRC, started a few months ago on the previous F27 and
continues now on F28. Before that I don't remember this behaviour to
I thought it was some smartd issue, and stopped this service
("/usr/bin/systemctl stop smartd.service") - to no avail: mounting the
internal disk still spins up the external ones.
The internal disk is identified by "smartctl -d test /dev/sda" like
[ ... ]
/dev/sda: Device of type 'scsi' [SCSI] detected
/dev/sda [SAT]: Device open changed type from 'scsi' to 'sat'
/dev/sda [SAT]: Device of type 'sat' [ATA] opened
(On a side note: I'm astonished that a smartctl simple info flag is
changing some device type like shown above)
External disks are identified by a smartctl test like so:
"[USB Sunplus]: Device of type 'usbsunplus' [ATA] detected"
the other one:
"[SAT]: Device of type 'sat' [ATA] detected"
Anyone an idea about where to start investigating this issue? Where
could such behaviour possibly be set up?
Thanks in anticipation.
Does Fedora 29 support the Intel RST (Rapid Storage Technology) chip for
hardware RAID? My new ThinkPad P72 came with an RST chip set up with two
2TB PCIe M.2 SSDs in a RAID1 config. The Fedora-29-MATE-Compiz spin DVD
doesn't "see" it. Nor does Clonezilla.
There's a BIOS mode setting for the Intel RST: "RST" mode for RAID, and
"AHCI" mode for separate SATA drives. Changing that setting to AHCI will
probably break the RAID1 array and render the P72 unbootable. I don't know
if that would a destructive, irreversible change, or if changing the mode
setting back to RST would restore everything.
I've only tried the MATE spin. One purpose of this question is to find out
if the full installation DVD supports the Intel RST chip.
Robert G. (Doc) Savage
Fairview Heights, IL
"Perfection is the enemy of good enough."
-- Admiral of the Fleet Sergei G. Gorshkov
I get *Failed to start Load Kernel Modules* during the boot.
Everytime Kernel is updated VirtualBox modules fail I have to reboot into
the new Kernel, run the following commands and then it starts working.
$ sudo akmods --force
$ sudo dracut -v -f
$ sudo grub2-mkconfig -o /boot/efi/EFI/fedora/grub.cfg
Then everything starts working again and the boot error goes away. You can
found the background of the issue in the link below.
My question is how can I automate this task.
(after a looong time not using Fedora, just back to it!)
I've tried installing Fedora on a Zotac Zbox CI327 (Intel Celeron
N3450 inside) but this happens to fail. I've tried F25 but it has
not the right kernel to make it (I've read about 4.10 minimum), then
tried F26-Alpha-1.7 Live and Rawhide-20170518 Live but none could
reach the graphical login. They both boot, some steps take a lot of
time and I end up in a state I don't understand but which is not
Here's a link to a rdsosreport.txt file generated using Rawhide, I must
admit that I don't know what to do now..
BTW, I could install and run a Ubuntu 17.10 daily
(artful-desktop-amd64-20170519.iso) - wow it starts up pretty quickly -
and that gave me hope!
Any hint or experience w/ such hardware?
When I start one of the two vpn definitions, that have been in
networkmanager for years and used to work fine (I haven't used them in
quite a while), it starts and I get a pop-up message saying that
interface tun0 has been activated in the firewall default zone (being
fedoraworkstation). This interface remains active for about a minute or
so until I get the pop-up message that interface tun0 has been
deactivated in the firewall default zone, and the vpn is no longer
connected. The vpn connection is using Openvpn.
I have checked dmesg for any message relative to tun0 or firewall
and there are no messages for either. How do I determine why the vpn
won't stay active?
I'm getting "filesystem not responding" messages from an NFS-mounted
NAS which I suspect is just slow (it spins down its disks when not in
use). I'm using automount and that appears to be related as it never
used to happen with normal mounting. I've changed the 'timeo' parameter
in the /etc/fstab line and run 'mount -a' but the mount parameters for
the filesystem have not changed. I've also restarted anything that
seems relevant from systemd:
systemctl restart storage-Backups.mount
systemctl restart proc-fs-nfsd.mount
systemctl restart proc-sys-fs-binfmt_misc.automount
to no effect.
How can I get this to work without rebooting?
Thanks to all.
The kensington Expert Track ball arrived today. Crazy Michigan
no-fault... It had to be ordered via a doctors order for workstation
modification and then through an approved medical supply house that
could only order it directly from Kensington...
But it is here and I CAN work with it left-handed. This keeps my right
hand on the keyboard with less stress not having to reach for a
right-hand mouse (I just could not control a regular mouse left-handed).
This is going to make a difference in my work and my recovery.
BTW, I am taking my first steps without a cane and am 'graduating' to
out-patient PT for the walking. But the dislocated shoulder has another
3 weeks to go...
Since I set the night light mode in manual, I cannot return to
How can I change this set up to default?
Patrick DUPRÉ | | email: pdupre(a)gmx.com
Laboratoire de Physico-Chimie de l'Atmosphère | |
Université du Littoral-Côte d'Opale | |
Tel. (33)-(0)3 28 23 76 12 | | Fax: 03 28 65 82 44
189A, avenue Maurice Schumann | | 59140 Dunkerque, France