Something on sourceforge has been recommended to me, but I try to
stick to things that dnf can install. Surely there must be some Fedora-
native ebook reader!
Beartooth Staffwright, Not Quite Clueless Power User
Remember I know little (precious little!) of where up is.
I am planning on running a Virtual Private Network from my Fedora
firewall out to a UML virtual colo (running RH9) at another site.
That site will be the place I present services to the world;
httpd, ssh, sftp, smtp. This is to comply with the "no servers"
and dynamic ip restrictions on my Comcast connection to the net;
if my firewall always drives an outbound connection to the
colocation site, I am not worried about changes of ip address,
and I am not opening any inbound ports.
There are a number of options for the VPN - the most attractive
are cipe ( http://sites.inka.de/sites/bigred/devel/cipe.html )
and FreeSwan ( http://www.freeswan.org/ ), though I am told that
one can do all this through an ssh tunnel. I would rather have
simple and secure than super-duper; I have plenty of bandwidth,
and will send outbound http and smtp from the firewall, so the
main bandwidth user will be incoming spam/b/b/b/b mail.
Anyone have some experiences to share about setting up VPN? Is
there anything about either cipe or FreeSwan that is likely to
break with FC1 or FC2?
Keith Lofstrom keithl(a)ieee.org Voice (503)-520-1993
KLIC --- Keith Lofstrom Integrated Circuits --- "Your Ideas in Silicon"
Design Contracting in Bipolar and CMOS - Analog, Digital, and Scan ICs
(after a looong time not using Fedora, just back to it!)
I've tried installing Fedora on a Zotac Zbox CI327 (Intel Celeron
N3450 inside) but this happens to fail. I've tried F25 but it has
not the right kernel to make it (I've read about 4.10 minimum), then
tried F26-Alpha-1.7 Live and Rawhide-20170518 Live but none could
reach the graphical login. They both boot, some steps take a lot of
time and I end up in a state I don't understand but which is not
Here's a link to a rdsosreport.txt file generated using Rawhide, I must
admit that I don't know what to do now..
BTW, I could install and run a Ubuntu 17.10 daily
(artful-desktop-amd64-20170519.iso) - wow it starts up pretty quickly -
and that gave me hope!
Any hint or experience w/ such hardware?
So... I did a "sudo dnf upgrade" and things seemed to do well.
However, when I rebooted, it hangs on bootup with the statment "Holding
until bootup processes complete" or something like that -- I'm doing
this from memory. I tried with a couple of older kernels, but they also
I assume that this is some transient thing associated with the upgrade.
Over the years, I've had glitches appear on an upgrade and disappear on
the next upgrade. Accordingly, I'd like to boot into rescue mode and
see if I can upgrade again.
However, I've forgotten how to turn on wifi networking from rescue mode.
Can anybody point me to a tutorial?
Is there an alternative to skype which would also allow me to exchange
Patrick DUPRÉ | | email: pdupre(a)gmx.com
Laboratoire de Physico-Chimie de l'Atmosphère | |
Université du Littoral-Côte d'Opale | |
Tel. (33)-(0)3 28 23 76 12 | | Fax: 03 28 65 82 44
189A, avenue Maurice Schumann | | 59140 Dunkerque, France
After upgrading to F27, I noticed that fonts looked "off". I made a
screenshot of Thunderbird and gnome-terminal displaying roughly
identical contents on Fedora 25, 26, and 27. The older two releases are
identical, but F27's fonts (both fixed-width and variable-width) appear
to be the same width as they were previously, but taller. Characters
like monospace 'o' used to be round and are now oblong. Everything
seems slightly heavier as a result of the additional pixels. Does
anyone know if this change was intentional? Personally, I think it's
worse than before.
Since March 08, I've received 11 messages from this list that appear empty, including 2 so far today. I have received a few (less) not empty, none today and 3 yesterday. What's causing this problem, and how do I fix it? My e-mail client is Thunderbird 52.5.2.
I will occasionally check the Fedora Hyperkitty for replies.
I just did an update from F25 to F26 via dnf. After it boots, I can no
longer start gnome terminal (nothing shows). If I ssh into the machine and
try it remotely, I see the following:
(process:3586): Gtk-WARNING **: Locale not supported by C library.
Using the fallback 'C' locale.
Error constructing proxy for
org.gnome.Terminal:/org/gnome/Terminal/Factory0: Error calling
StartServiceByName for org.gnome.Terminal: Timeout was reached
So it looks like there is a locale issue in my update. Does anyone know
how to fix this?