Hello, I've just returned one relatively new disk drive[*], and hope I'm not about to return another... [*] It was a 1TB Samsung ecogreen, and some strenuous testing would reliably provoke I/O errors which would apparently damage the disk enough to force an increase in the SMART Reallocated_Sector_Ct metric. My final test added about 600 to that count. Of all my other disks, some over 5 years old, only 1 had a single Reallocated_Sector_Ct. The rest were 0. Anyhow, this time it's my newest drive, a 1.5TB Samsung. Most of the time it is spun down, but spins up and works fine when I need it, which is once a day or so, for backups. But today, there was no trace of it at all. /dev/sdb had disappeared altogether. Ominous. This is up-to-date F12 w/stock untainted 2.6.31.9-174.fc12.x86_64 on an Intel Q9450. dmesg has clues: ... usb 1-5.2: new low speed USB device using ehci_hcd and address 40 usb 1-5.2: New USB device found, idVendor=046d, idProduct=c03e usb 1-5.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5.2: Product: USB-PS/2 Optical Mouse usb 1-5.2: Manufacturer: Logitech usb 1-5.2: configuration #1 chosen from 1 choice input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:1a.7/usb1/1-5/1-5.2/1-5.2:1.0/input/input29 generic-usb 0003:046D:C03E.001A: input,hidraw1: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1a.7-5.2/input0 [maybe related? The above are common events provoked by my turning off/on the monitor+hub that my kbd and mouse are usually plugged into. ] Here's the bad part: ata3.00: exception Emask 0x10 SAct 0x0 SErr 0x4000000 action 0xe frozen ata3.00: irq_stat 0x00000040, connection status changed ata3: SError: { DevExch } ata3.00: cmd ec/00:01:00:00:00/00:00:00:00:00/00 tag 0 pio 512 in res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) ata3.00: status: { DRDY } ata3: hard resetting link ata3: SATA link down (SStatus 0 SControl 300) ata3: hard resetting link ata3: SATA link down (SStatus 0 SControl 300) ata3: limiting SATA link speed to 1.5 Gbps ata3: hard resetting link ata3: SATA link down (SStatus 0 SControl 310) ata3.00: disabled ata3: EH complete ata3.00: detaching (SCSI 2:0:0:0) sd 2:0:0:0: [sdb] Synchronizing SCSI cache sd 2:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK sd 2:0:0:0: [sdb] Stopping disk sd 2:0:0:0: [sdb] START_STOP FAILED sd 2:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK Here are lspci and the complete dmesg output: 00:00.0 Host bridge: Intel Corporation 82Q35 Express DRAM Controller (rev 02) 00:02.0 VGA compatible controller: Intel Corporation 82Q35 Express Integrated Graphics Controller (rev 02) 00:02.1 Display controller: Intel Corporation 82Q35 Express Integrated Graphics Controller (rev 02) 00:03.0 Communication controller: Intel Corporation 82Q35 Express MEI Controller (rev 02) 00:19.0 Ethernet controller: Intel Corporation 82566DM-2 Gigabit Network Connection (rev 02) 00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 02) 00:1a.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 02) 00:1a.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 02) 00:1a.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 02) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 (rev 02) 00:1c.2 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 3 (rev 02) 00:1c.3 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 4 (rev 02) 00:1c.4 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 (rev 02) 00:1d.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 02) 00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 02) 00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 02) 00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 92) 00:1f.0 ISA bridge: Intel Corporation 82801IO (ICH9DO) LPC Interface Controller (rev 02) 00:1f.2 SATA controller: Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 6 port SATA AHCI Controller (rev 02) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 02) 03:00.0 IDE interface: Marvell Technology Group Ltd. 88SE6101 single-port PATA133 interface (rev b1) 06:00.0 Ethernet controller: D-Link System Inc DGE-528T Gigabit Ethernet Adapter (rev 10) 06:03.0 FireWire (IEEE 1394): Agere Systems FW322/323 (rev 70) Initializing cgroup subsys cpuset Initializing cgroup subsys cpu Linux version 2.6.31.9-174.fc12.x86_64 (mockbuild(a)x86-01.phx2.fedoraproject.org) (gcc version 4.4.2 20091027 (Red Hat 4.4.2-7) (GCC) ) #1 SMP Mon Dec 21 05:33:33 UTC 2009 Command line: ro root=UUID=f98e9849-f5d0-4ea5-9853-2c492804ef38 LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYBOARDTYPE=pc KEYTABLE=us nodmraid 5 ... Initalizing network drop monitor service ata6: SATA link down (SStatus 0 SControl 300) ata4: SATA link down (SStatus 0 SControl 300) usb 1-5: new high speed USB device using ehci_hcd and address 2 usb 1-5: New USB device found, idVendor=0409, idProduct=0058 usb 1-5: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5: Product: USB2.0 Hub Controller usb 1-5: Manufacturer: NEC Corporation usb 1-5: configuration #1 chosen from 1 choice hub 1-5:1.0: USB hub found hub 1-5:1.0: 4 ports detected usb 1-5.2: new low speed USB device using ehci_hcd and address 3 usb 1-5.2: New USB device found, idVendor=046d, idProduct=c03e usb 1-5.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5.2: Product: USB-PS/2 Optical Mouse usb 1-5.2: Manufacturer: Logitech usb 1-5.2: configuration #1 chosen from 1 choice input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:1a.7/usb1/1-5/1-5.2/1-5.2:1.0/input/input3 generic-usb 0003:046D:C03E.0001: input,hidraw0: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1a.7-5.2/input0 ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata5.00: ATA-7: OCZ SUMMIT, VBM1801Q, max UDMA/100 ata5.00: 250069680 sectors, multi 16: LBA48 NCQ (depth 31/32) ata5.00: configured for UDMA/100 ata3.00: ATA-7: SAMSUNG HD154UI, 1AG01118, max UDMA7 ata3.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata3.00: configured for UDMA/133 ata2.00: ATAPI: LITE-ON DVDRW LH-20A1S, 9L05, max UDMA/100, ATAPI AN ata2.00: configured for UDMA/100 ata1.00: ATA-7: ST3320620AS, 3.AAK, max UDMA/133 ata1.00: 625142448 sectors, multi 0: LBA48 NCQ (depth 31/32) ata1.00: configured for UDMA/133 usb 1-5.1: new low speed USB device using ehci_hcd and address 4 scsi 0:0:0:0: Direct-Access ATA ST3320620AS 3.AA PQ: 0 ANSI: 5 sd 0:0:0:0: Attached scsi generic sg0 type 0 sd 0:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: scsi 1:0:0:0: CD-ROM LITE-ON DVDRW LH-20A1S 9L05 PQ: 0 ANSI: 5 sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.20 sr 1:0:0:0: Attached scsi CD-ROM sr0 sr 1:0:0:0: Attached scsi generic sg1 type 5 scsi 2:0:0:0: Direct-Access ATA SAMSUNG HD154UI 1AG0 PQ: 0 ANSI: 5 sd 2:0:0:0: Attached scsi generic sg2 type 0 sd 2:0:0:0: [sdb] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB) sd 2:0:0:0: [sdb] Write Protect is off sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdb: scsi 4:0:0:0: Direct-Access ATA OCZ SUMMIT VBM1 PQ: 0 ANSI: 5 sd 4:0:0:0: Attached scsi generic sg3 type 0 sd 4:0:0:0: [sdc] 250069680 512-byte logical blocks: (128 GB/119 GiB) sd 4:0:0:0: [sdc] Write Protect is off sd 4:0:0:0: [sdc] Mode Sense: 00 3a 00 00 sd 4:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdc: sdc1 sdc2 sdc3 sdc4 sdc5 sdc6 sdc7 sdc8 sdc9 sdc10 sdc11 sdc12 sd 4:0:0:0: [sdc] Attached SCSI disk sda1 sda2 sda3 sda4 < sda5 sd 2:0:0:0: [sdb] Attached SCSI disk sda6 sda7 sda8 usb 1-5.1: New USB device found, idVendor=413c, idProduct=2003 usb 1-5.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5.1: Product: Dell USB Keyboard usb 1-5.1: Manufacturer: Dell usb 1-5.1: configuration #1 chosen from 1 choice sda9 > sd 0:0:0:0: [sda] Attached SCSI disk Freeing unused kernel memory: 1324k freed Write protecting the kernel read-only data: 6356k input: Dell Dell USB Keyboard as /devices/pci0000:00/0000:00:1a.7/usb1/1-5/1-5.1/1-5.1:1.0/input/input4 generic-usb 0003:413C:2003.0002: input,hidraw1: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-0000:00:1a.7-5.1/input0 dracut: dracut-002-13.4.git8f397a9b.fc12 udev: starting version 145 [drm] Initialized drm 1.1.0 20060810 alloc irq_desc for 16 on node 0 alloc kstat_irqs on node 0 i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 i915 0000:00:02.0: setting latency timer to 64 alloc irq_desc for 34 on node 0 alloc kstat_irqs on node 0 i915 0000:00:02.0: irq 34 for MSI/MSI-X [drm] DAC-6: set mode 1600x1200 16 Console: switching to colour frame buffer device 200x75 fb0: inteldrmfb frame buffer device registered panic notifier [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0 dracut: Starting plymouth daemon dracut: rd_NO_DM: removing DM RAID activation dracut: rd_NO_MDIMSM: no MD RAID for imsm/isw raids pata_marvell 0000:03:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 pata_marvell 0000:03:00.0: setting latency timer to 64 scsi6 : pata_marvell scsi7 : pata_marvell ata7: PATA max UDMA/100 cmd 0x2018 ctl 0x2024 bmdma 0x2000 irq 18 ata8: DUMMY EXT4-fs (sdc2): barriers enabled kjournald2 starting: pid 294, dev sdc2:8, commit interval 5 seconds EXT4-fs (sdc2): delayed allocation enabled EXT4-fs: file extents enabled EXT4-fs: mballoc enabled EXT4-fs (sdc2): mounted filesystem with ordered data mode dracut: Mounted root filesystem /dev/sdc2 dracut: Loading SELinux policy type=1404 audit(1263827246.818:2): enforcing=1 old_enforcing=0 auid=4294967295 ses=4294967295 SELinux: 8192 avtab hash slots, 148895 rules. SELinux: 8192 avtab hash slots, 148895 rules. SELinux: 8 users, 12 roles, 3017 types, 145 bools, 1 sens, 1024 cats SELinux: 75 classes, 148895 rules SELinux: Completing initialization. SELinux: Setting up existing superblocks. SELinux: initialized (dev sdc2, type ext4), uses xattr SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts SELinux: initialized (dev securityfs, type securityfs), uses genfs_contexts SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses transition SIDs SELinux: initialized (dev devpts, type devpts), uses transition SIDs SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs SELinux: initialized (dev anon_inodefs, type anon_inodefs), uses genfs_contexts SELinux: initialized (dev pipefs, type pipefs), uses task SIDs SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts SELinux: initialized (dev sockfs, type sockfs), uses task SIDs SELinux: initialized (dev proc, type proc), uses genfs_contexts SELinux: initialized (dev bdev, type bdev), uses genfs_contexts SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts type=1403 audit(1263827247.009:3): policy loaded auid=4294967295 ses=4294967295 dracut: Switching root udev: starting version 145 e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k2 e1000e: Copyright (c) 1999-2008 Intel Corporation. e1000e 0000:00:19.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 e1000e 0000:00:19.0: pci_enable_pcie_error_reporting failed 0xfffffffb e1000e 0000:00:19.0: setting latency timer to 64 alloc irq_desc for 35 on node 0 alloc kstat_irqs on node 0 e1000e 0000:00:19.0: irq 35 for MSI/MSI-X iTCO_vendor_support: vendor-support=0 iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05 iTCO_wdt: Found a ICH9DO TCO device (Version=2, TCOBASE=0x0460) iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) firewire_ohci 0000:06:03.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 firewire_ohci: Added fw-ohci device 0000:06:03.0, OHCI version 1.0 r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded r8169 0000:06:00.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21 r8169 0000:06:00.0: no PCI Express capability eth0: RTL8169sb/8110sb at 0xffffc900097b8000, 00:1e:58:e7:47:a7, XID 10000000 IRQ 21 0000:00:19.0: eth1: (PCI Express:2.5GB/s:Width x1) 00:19:d1:ad:7a:e5 0000:00:19.0: eth1: Intel(R) PRO/1000 Network Connection 0000:00:19.0: eth1: MAC: 7, PHY: 6, PBA No: ffffff-0ff i801_smbus 0000:00:1f.3: PCI INT B -> GSI 18 (level, low) -> IRQ 18 alloc irq_desc for 22 on node 0 alloc kstat_irqs on node 0 HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 HDA Intel 0000:00:1b.0: setting latency timer to 64 firewire_core: created device fw0: GUID 0090270001e8e462, S400 hda_codec: Unknown model for ALC268, trying auto-probe from BIOS... ALSA sound/pci/hda/hda_codec.c:3862: autoconfig: line_outs=1 (0x14/0x0/0x0/0x0/0x0) ALSA sound/pci/hda/hda_codec.c:3866: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0) ALSA sound/pci/hda/hda_codec.c:3870: hp_outs=1 (0x15/0x0/0x0/0x0/0x0) ALSA sound/pci/hda/hda_codec.c:3871: mono: mono_out=0x0 ALSA sound/pci/hda/hda_codec.c:3882: inputs: mic=0x18, fmic=0x1a, line=0x19, fline=0x0, cd=0x0, aux=0x0 ALSA sound/pci/hda/patch_realtek.c:1181: realtek: No valid SSID, checking pincfg 0x411111f0 for NID 0x1d ALSA sound/pci/hda/patch_realtek.c:1255: realtek: Enable default setup for auto mode as fallback input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input5 name_count maxed, losing inode data: dev=00:05, inode=10700 name_count maxed, losing inode data: dev=00:05, inode=10700 name_count maxed, losing inode data: dev=00:05, inode=10700 name_count maxed, losing inode data: dev=00:05, inode=10700 name_count maxed, losing inode data: dev=00:05, inode=10700 name_count maxed, losing inode data: dev=00:05, inode=10700 name_count maxed, losing inode data: dev=00:05, inode=10700 name_count maxed, losing inode data: dev=00:05, inode=10700 name_count maxed, losing inode data: dev=00:05, inode=10700 name_count maxed, losing inode data: dev=00:05, inode=10700 name_count maxed, losing inode data: dev=00:05, inode=10700 name_count maxed, losing inode data: dev=00:05, inode=10700 name_count maxed, losing inode data: dev=00:05, inode=10700 name_count maxed, losing inode data: dev=00:05, inode=10700 name_count maxed, losing inode data: dev=00:05, inode=10700 name_count maxed, losing inode data: dev=00:05, inode=10700 name_count maxed, losing inode data: dev=00:05, inode=10700 name_count maxed, losing inode data: dev=00:05, inode=10700 name_count maxed, losing inode data: dev=00:05, inode=10700 name_count maxed, losing inode data: dev=00:05, inode=10700 name_count maxed, losing inode data: dev=00:05, inode=10700 name_count maxed, losing inode data: dev=00:05, inode=10700 name_count maxed, losing inode data: dev=00:05, inode=10700 device-mapper: multipath: version 1.1.0 loaded EXT4-fs (sdc2): internal journal on sdc2:8 EXT4-fs (sdc1): barriers enabled kjournald2 starting: pid 861, dev sdc1:8, commit interval 5 seconds EXT4-fs (sdc1): internal journal on sdc1:8 EXT4-fs (sdc1): delayed allocation enabled EXT4-fs: file extents enabled EXT4-fs: mballoc enabled EXT4-fs (sdc1): mounted filesystem with ordered data mode SELinux: initialized (dev sdc1, type ext4), uses xattr EXT4-fs (sdc5): barriers enabled kjournald2 starting: pid 866, dev sdc5:8, commit interval 5 seconds EXT4-fs (sdc5): internal journal on sdc5:8 EXT4-fs (sdc5): delayed allocation enabled EXT4-fs: file extents enabled EXT4-fs: mballoc enabled EXT4-fs (sdc5): mounted filesystem with ordered data mode SELinux: initialized (dev sdc5, type ext4), uses xattr EXT4-fs (sdc12): barriers enabled kjournald2 starting: pid 871, dev sdc12:8, commit interval 5 seconds EXT4-fs (sdc12): internal journal on sdc12:8 EXT4-fs (sdc12): delayed allocation enabled EXT4-fs: file extents enabled EXT4-fs: mballoc enabled EXT4-fs (sdc12): mounted filesystem with ordered data mode SELinux: initialized (dev sdc12, type ext4), uses xattr EXT4-fs (sdc3): barriers enabled kjournald2 starting: pid 876, dev sdc3:8, commit interval 5 seconds EXT4-fs (sdc3): internal journal on sdc3:8 EXT4-fs (sdc3): delayed allocation enabled EXT4-fs: file extents enabled EXT4-fs: mballoc enabled EXT4-fs (sdc3): mounted filesystem with ordered data mode SELinux: initialized (dev sdc3, type ext4), uses xattr EXT4-fs (sdc4): barriers enabled kjournald2 starting: pid 881, dev sdc4:8, commit interval 5 seconds EXT4-fs (sdc4): internal journal on sdc4:8 EXT4-fs (sdc4): delayed allocation enabled EXT4-fs: file extents enabled EXT4-fs: mballoc enabled EXT4-fs (sdc4): mounted filesystem with ordered data mode SELinux: initialized (dev sdc4, type ext4), uses xattr SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled SGI XFS Quota Management subsystem XFS mounting filesystem sdc6 Ending clean XFS mount for filesystem: sdc6 SELinux: initialized (dev sdc6, type xfs), uses xattr segctord starting. Construction interval = 5 seconds, CP frequency < 30 seconds NILFS warning: mounting unchecked fs NILFS: recovery complete. SELinux: initialized (dev sdc7, type nilfs2), not configured for labeling SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs Adding 2097144k swap on /dev/sdc10. Priority:-1 extents:1 across:2097144k SS Adding 2097144k swap on /dev/sdc11. Priority:-2 extents:1 across:2097144k SS SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts microcode: CPU0 sig=0x10676, pf=0x10, revision=0x0 platform microcode: firmware: requesting intel-ucode/06-17-06 microcode: CPU1 sig=0x10676, pf=0x10, revision=0x0 platform microcode: firmware: requesting intel-ucode/06-17-06 microcode: CPU2 sig=0x10676, pf=0x10, revision=0x0 platform microcode: firmware: requesting intel-ucode/06-17-06 microcode: CPU3 sig=0x10676, pf=0x10, revision=0x0 platform microcode: firmware: requesting intel-ucode/06-17-06 Microcode Update Driver: v2.00 <tigran(a)aivazian.fsnet.co.uk&gt;, Peter Oruba microcode: CPU0 updated to revision 0x60c, date = 2008-01-19 microcode: CPU1 updated to revision 0x60c, date = 2008-01-19 microcode: CPU2 updated to revision 0x60c, date = 2008-01-19 microcode: CPU3 updated to revision 0x60c, date = 2008-01-19 Microcode Update Driver: v2.00 removed. NET: Registered protocol family 10 lo: Disabled Privacy Extensions ip6_tables: (C) 2000-2006 Netfilter Core Team RPC: Registered udp transport module. RPC: Registered tcp transport module. SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts coretemp coretemp.0: Using relative temperature scale! coretemp coretemp.1: Using relative temperature scale! coretemp coretemp.2: Using relative temperature scale! coretemp coretemp.3: Using relative temperature scale! Installing knfsd (copyright (C) 1996 okir(a)monad.swb.de). SELinux: initialized (dev nfsd, type nfsd), uses genfs_contexts e1000e 0000:00:19.0: irq 35 for MSI/MSI-X e1000e 0000:00:19.0: irq 35 for MSI/MSI-X ADDRCONF(NETDEV_UP): eth1: link is not ready r8169: eth0: link up r8169: eth0: link up NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory NFSD: starting 90-second grace period e1000e: eth1 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX 0000:00:19.0: eth1: 10/100 speed: disabling TSO ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready eth0: no IPv6 routers present eth1: no IPv6 routers present type=1305 audit(1263827274.679:38409): audit_enabled=0 old=1 auid=4294967295 ses=4294967295 subj=system_u:system_r:readahead_t:s0 res=1 type=1400 audit(1263827274.950:38410): avc: denied { search } for pid=318 comm="readahead-colle" name="/" dev=sdc7 ino=2 scontext=system_u:system_r:readahead_t:s0 tcontext=system_u:object_r:unlabeled_t:s0 tclass=dir fuse init (API version 7.12) SELinux: initialized (dev fuse, type fuse), uses genfs_contexts git[26201]: segfault at 1ab7000 ip 00000000004788f0 sp 00007fff327ef7d0 error 4 in git[400000+fa000] git[26230]: segfault at 17a0000 ip 00000000004788f0 sp 00007fff4e18d960 error 4 in git[400000+fa000] git[29459]: segfault at 12fd000 ip 00000000004789e0 sp 00007fff42f1f540 error 4 in git[400000+fa000] git[32457]: segfault at 223b000 ip 000000000049599e sp 00007fff26d624e0 error 4 in git[400000+13a000] git[32483]: segfault at 11d4000 ip 000000000049599e sp 00007fffe35e8740 error 4 in git[400000+13a000] git[32511]: segfault at 196d000 ip 000000000049599e sp 00007fff4bebd630 error 4 in git[400000+13a000] git[32628]: segfault at 1a24000 ip 000000000049599e sp 00007fff3176f3d0 error 4 in git[400000+13a000] git[3036]: segfault at 1592000 ip 00000000004789e0 sp 00007fffed0a6080 error 4 in git[400000+fa000] git[6316]: segfault at 1006000 ip 0000000000478a70 sp 00007fffdbf9abe0 error 4 in git[400000+fa000] git[6330]: segfault at 13e5000 ip 0000000000478a70 sp 00007fff151e6d10 error 4 in git[400000+fa000] git[8762]: segfault at 1c08000 ip 0000000000478a70 sp 00007fff958cee00 error 4 in git[400000+fa000] git[11246]: segfault at 2120000 ip 0000000000478900 sp 00007fffb064df20 error 4 in git[400000+fa000] git[13743]: segfault at 1dd2000 ip 00000000004788b0 sp 00007fff72c23ef0 error 4 in git[400000+fa000] git[16265]: segfault at 1c65000 ip 0000000000478460 sp 00007fffc06cd410 error 4 in git[400000+f9000] git[9097]: segfault at 25ee000 ip 0000000000478530 sp 00007fff1e18e210 error 4 in git[400000+f9000] git[11547]: segfault at 126b000 ip 0000000000478460 sp 00007fff694a3eb0 error 4 in git[400000+f9000] git[13986]: segfault at 1e48000 ip 0000000000478460 sp 00007fff8fd31d30 error 4 in git[400000+f9000] git[19353]: segfault at ccb000 ip 0000000000477530 sp 00007fff1608f050 error 4 in git[400000+f3000] git[21796]: segfault at 23e3000 ip 0000000000477fd0 sp 00007fffcc0da500 error 4 in git[400000+f3000] git[24763]: segfault at 1909000 ip 0000000000475660 sp 00007fff187b16e0 error 4 in git[400000+ef000] git[3030]: segfault at 25a5000 ip 000000000049599e sp 00007fff6e57f4b0 error 4 in git[400000+13a000] git[3042]: segfault at 20d7000 ip 000000000049599e sp 00007fff398a48e0 error 4 in git[400000+13a000] drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (0030) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (0030) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.1/input0, status -71 usb 1-5: clear tt 1 (0040) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (0030) error -71 usb 1-5: USB disconnect, address 2 usb 1-5.1: USB disconnect, address 4 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (0030) error -19 usb 1-5.2: USB disconnect, address 3 usb 1-5: new high speed USB device using ehci_hcd and address 5 usb 1-5: New USB device found, idVendor=0409, idProduct=0058 usb 1-5: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5: Product: USB2.0 Hub Controller usb 1-5: Manufacturer: NEC Corporation usb 1-5: configuration #1 chosen from 1 choice hub 1-5:1.0: USB hub found hub 1-5:1.0: 4 ports detected usb 1-5.1: new low speed USB device using ehci_hcd and address 6 usb 1-5.1: New USB device found, idVendor=413c, idProduct=2003 usb 1-5.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5.1: Product: Dell USB Keyboard usb 1-5.1: Manufacturer: Dell usb 1-5.1: configuration #1 chosen from 1 choice input: Dell Dell USB Keyboard as /devices/pci0000:00/0000:00:1a.7/usb1/1-5/1-5.1/1-5.1:1.0/input/input6 generic-usb 0003:413C:2003.0003: input,hidraw0: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-0000:00:1a.7-5.1/input0 usb 1-5.2: new low speed USB device using ehci_hcd and address 7 usb 1-5.2: New USB device found, idVendor=046d, idProduct=c03e usb 1-5.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5.2: Product: USB-PS/2 Optical Mouse usb 1-5.2: Manufacturer: Logitech usb 1-5.2: configuration #1 chosen from 1 choice input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:1a.7/usb1/1-5/1-5.2/1-5.2:1.0/input/input7 generic-usb 0003:046D:C03E.0004: input,hidraw1: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1a.7-5.2/input0 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (0070) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (0070) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.1/input0, status -71 usb 1-5: clear tt 1 (0060) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (0070) error -71 usb 1-5: USB disconnect, address 5 usb 1-5.1: USB disconnect, address 6 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (0070) error -19 usb 1-5.2: USB disconnect, address 7 usb 1-5: new high speed USB device using ehci_hcd and address 8 usb 1-5: New USB device found, idVendor=0409, idProduct=0058 usb 1-5: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5: Product: USB2.0 Hub Controller usb 1-5: Manufacturer: NEC Corporation usb 1-5: configuration #1 chosen from 1 choice hub 1-5:1.0: USB hub found hub 1-5:1.0: 4 ports detected usb 1-5.1: new low speed USB device using ehci_hcd and address 9 usb 1-5.1: New USB device found, idVendor=413c, idProduct=2003 usb 1-5.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5.1: Product: Dell USB Keyboard usb 1-5.1: Manufacturer: Dell usb 1-5.1: configuration #1 chosen from 1 choice input: Dell Dell USB Keyboard as /devices/pci0000:00/0000:00:1a.7/usb1/1-5/1-5.1/1-5.1:1.0/input/input8 generic-usb 0003:413C:2003.0005: input,hidraw0: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-0000:00:1a.7-5.1/input0 usb 1-5.2: new low speed USB device using ehci_hcd and address 10 usb 1-5.2: New USB device found, idVendor=046d, idProduct=c03e usb 1-5.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5.2: Product: USB-PS/2 Optical Mouse usb 1-5.2: Manufacturer: Logitech usb 1-5.2: configuration #1 chosen from 1 choice input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:1a.7/usb1/1-5/1-5.2/1-5.2:1.0/input/input9 generic-usb 0003:046D:C03E.0006: input,hidraw1: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1a.7-5.2/input0 SELinux: 8192 avtab hash slots, 150068 rules. SELinux: 8192 avtab hash slots, 150068 rules. SELinux: 8 users, 12 roles, 3029 types, 146 bools, 1 sens, 1024 cats SELinux: 75 classes, 150068 rules drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (00a0) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (00a0) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.1/input0, status -71 usb 1-5: clear tt 1 (0090) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (00a0) error -71 usb 1-5: USB disconnect, address 8 usb 1-5.1: USB disconnect, address 9 usb 1-5.2: USB disconnect, address 10 usb 1-5: new high speed USB device using ehci_hcd and address 11 usb 1-5: New USB device found, idVendor=0409, idProduct=0058 usb 1-5: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5: Product: USB2.0 Hub Controller usb 1-5: Manufacturer: NEC Corporation usb 1-5: configuration #1 chosen from 1 choice hub 1-5:1.0: USB hub found hub 1-5:1.0: 4 ports detected usb 1-5.1: new low speed USB device using ehci_hcd and address 12 usb 1-5.1: New USB device found, idVendor=413c, idProduct=2003 usb 1-5.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5.1: Product: Dell USB Keyboard usb 1-5.1: Manufacturer: Dell usb 1-5.1: configuration #1 chosen from 1 choice input: Dell Dell USB Keyboard as /devices/pci0000:00/0000:00:1a.7/usb1/1-5/1-5.1/1-5.1:1.0/input/input10 generic-usb 0003:413C:2003.0007: input,hidraw0: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-0000:00:1a.7-5.1/input0 usb 1-5.2: new low speed USB device using ehci_hcd and address 13 usb 1-5.2: New USB device found, idVendor=046d, idProduct=c03e usb 1-5.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5.2: Product: USB-PS/2 Optical Mouse usb 1-5.2: Manufacturer: Logitech usb 1-5.2: configuration #1 chosen from 1 choice input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:1a.7/usb1/1-5/1-5.2/1-5.2:1.0/input/input11 generic-usb 0003:046D:C03E.0008: input,hidraw1: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1a.7-5.2/input0 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (00d0) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.1/input0, status -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (00c0) error -71 usb 1-5: clear tt 1 (00d0) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (00d0) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (00d0) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.1/input0, status -71 usb 1-5: USB disconnect, address 11 usb 1-5.1: USB disconnect, address 12 usb 1-5: clear tt 1 (00c0) error -71 usb 1-5.2: USB disconnect, address 13 usb 1-5: new high speed USB device using ehci_hcd and address 14 usb 1-5: New USB device found, idVendor=0409, idProduct=0058 usb 1-5: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5: Product: USB2.0 Hub Controller usb 1-5: Manufacturer: NEC Corporation usb 1-5: configuration #1 chosen from 1 choice hub 1-5:1.0: USB hub found hub 1-5:1.0: 4 ports detected usb 1-5.1: new low speed USB device using ehci_hcd and address 15 usb 1-5.1: New USB device found, idVendor=413c, idProduct=2003 usb 1-5.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5.1: Product: Dell USB Keyboard usb 1-5.1: Manufacturer: Dell usb 1-5.1: configuration #1 chosen from 1 choice input: Dell Dell USB Keyboard as /devices/pci0000:00/0000:00:1a.7/usb1/1-5/1-5.1/1-5.1:1.0/input/input12 generic-usb 0003:413C:2003.0009: input,hidraw0: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-0000:00:1a.7-5.1/input0 usb 1-5.2: new low speed USB device using ehci_hcd and address 16 usb 1-5.2: New USB device found, idVendor=046d, idProduct=c03e usb 1-5.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5.2: Product: USB-PS/2 Optical Mouse usb 1-5.2: Manufacturer: Logitech usb 1-5.2: configuration #1 chosen from 1 choice input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:1a.7/usb1/1-5/1-5.2/1-5.2:1.0/input/input13 generic-usb 0003:046D:C03E.000A: input,hidraw1: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1a.7-5.2/input0 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (0100) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (0100) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.1/input0, status -71 usb 1-5: clear tt 1 (00f0) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (0100) error -71 usb 1-5: USB disconnect, address 14 usb 1-5.1: USB disconnect, address 15 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (0100) error -19 usb 1-5.2: USB disconnect, address 16 usb 1-5: new high speed USB device using ehci_hcd and address 17 usb 1-5: New USB device found, idVendor=0409, idProduct=0058 usb 1-5: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5: Product: USB2.0 Hub Controller usb 1-5: Manufacturer: NEC Corporation usb 1-5: configuration #1 chosen from 1 choice hub 1-5:1.0: USB hub found hub 1-5:1.0: 4 ports detected usb 1-5.1: new low speed USB device using ehci_hcd and address 18 usb 1-5.1: New USB device found, idVendor=413c, idProduct=2003 usb 1-5.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5.1: Product: Dell USB Keyboard usb 1-5.1: Manufacturer: Dell usb 1-5.1: configuration #1 chosen from 1 choice input: Dell Dell USB Keyboard as /devices/pci0000:00/0000:00:1a.7/usb1/1-5/1-5.1/1-5.1:1.0/input/input14 generic-usb 0003:413C:2003.000B: input,hidraw0: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-0000:00:1a.7-5.1/input0 usb 1-5.2: new low speed USB device using ehci_hcd and address 19 usb 1-5.2: New USB device found, idVendor=046d, idProduct=c03e usb 1-5.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5.2: Product: USB-PS/2 Optical Mouse usb 1-5.2: Manufacturer: Logitech usb 1-5.2: configuration #1 chosen from 1 choice input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:1a.7/usb1/1-5/1-5.2/1-5.2:1.0/input/input15 generic-usb 0003:046D:C03E.000C: input,hidraw1: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1a.7-5.2/input0 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (0130) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (0130) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.1/input0, status -71 usb 1-5: clear tt 1 (0120) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (0130) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: USB disconnect, address 17 usb 1-5.1: USB disconnect, address 18 usb 1-5: clear tt 1 (0130) error -71 usb 1-5.2: USB disconnect, address 19 usb 1-5: new high speed USB device using ehci_hcd and address 20 usb 1-5: New USB device found, idVendor=0409, idProduct=0058 usb 1-5: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5: Product: USB2.0 Hub Controller usb 1-5: Manufacturer: NEC Corporation usb 1-5: configuration #1 chosen from 1 choice hub 1-5:1.0: USB hub found hub 1-5:1.0: 4 ports detected usb 1-5.1: new low speed USB device using ehci_hcd and address 21 usb 1-5.1: New USB device found, idVendor=413c, idProduct=2003 usb 1-5.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5.1: Product: Dell USB Keyboard usb 1-5.1: Manufacturer: Dell usb 1-5.1: configuration #1 chosen from 1 choice input: Dell Dell USB Keyboard as /devices/pci0000:00/0000:00:1a.7/usb1/1-5/1-5.1/1-5.1:1.0/input/input16 generic-usb 0003:413C:2003.000D: input,hidraw0: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-0000:00:1a.7-5.1/input0 usb 1-5.2: new low speed USB device using ehci_hcd and address 22 usb 1-5.2: New USB device found, idVendor=046d, idProduct=c03e usb 1-5.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5.2: Product: USB-PS/2 Optical Mouse usb 1-5.2: Manufacturer: Logitech usb 1-5.2: configuration #1 chosen from 1 choice input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:1a.7/usb1/1-5/1-5.2/1-5.2:1.0/input/input17 generic-usb 0003:046D:C03E.000E: input,hidraw1: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1a.7-5.2/input0 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (0160) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (0160) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.1/input0, status -71 usb 1-5: clear tt 1 (0150) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (0160) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (0160) error -71 usb 1-5: USB disconnect, address 20 usb 1-5.1: USB disconnect, address 21 usb 1-5.2: USB disconnect, address 22 usb 1-5: new high speed USB device using ehci_hcd and address 23 usb 1-5: New USB device found, idVendor=0409, idProduct=0058 usb 1-5: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5: Product: USB2.0 Hub Controller usb 1-5: Manufacturer: NEC Corporation usb 1-5: configuration #1 chosen from 1 choice hub 1-5:1.0: USB hub found hub 1-5:1.0: 4 ports detected usb 1-5.2: new low speed USB device using ehci_hcd and address 24 usb 1-5.2: New USB device found, idVendor=046d, idProduct=c03e usb 1-5.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5.2: Product: USB-PS/2 Optical Mouse usb 1-5.2: Manufacturer: Logitech usb 1-5.2: configuration #1 chosen from 1 choice input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:1a.7/usb1/1-5/1-5.2/1-5.2:1.0/input/input18 generic-usb 0003:046D:C03E.000F: input,hidraw0: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1a.7-5.2/input0 usb 1-5.1: new low speed USB device using ehci_hcd and address 25 usb 1-5.1: New USB device found, idVendor=413c, idProduct=2003 usb 1-5.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5.1: Product: Dell USB Keyboard usb 1-5.1: Manufacturer: Dell usb 1-5.1: configuration #1 chosen from 1 choice input: Dell Dell USB Keyboard as /devices/pci0000:00/0000:00:1a.7/usb1/1-5/1-5.1/1-5.1:1.0/input/input19 generic-usb 0003:413C:2003.0010: input,hidraw1: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-0000:00:1a.7-5.1/input0 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (0180) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (0180) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.1/input0, status -71 usb 1-5: clear tt 1 (0190) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (0180) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: USB disconnect, address 23 usb 1-5.1: USB disconnect, address 25 usb 1-5: clear tt 1 (0180) error -71 usb 1-5.2: USB disconnect, address 24 usb 1-5: new high speed USB device using ehci_hcd and address 26 usb 1-5: New USB device found, idVendor=0409, idProduct=0058 usb 1-5: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5: Product: USB2.0 Hub Controller usb 1-5: Manufacturer: NEC Corporation usb 1-5: configuration #1 chosen from 1 choice hub 1-5:1.0: USB hub found hub 1-5:1.0: 4 ports detected usb 1-5.1: new low speed USB device using ehci_hcd and address 27 usb 1-5.1: New USB device found, idVendor=413c, idProduct=2003 usb 1-5.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5.1: Product: Dell USB Keyboard usb 1-5.1: Manufacturer: Dell usb 1-5.1: configuration #1 chosen from 1 choice input: Dell Dell USB Keyboard as /devices/pci0000:00/0000:00:1a.7/usb1/1-5/1-5.1/1-5.1:1.0/input/input20 generic-usb 0003:413C:2003.0011: input,hidraw0: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-0000:00:1a.7-5.1/input0 usb 1-5.2: new low speed USB device using ehci_hcd and address 28 usb 1-5.2: New USB device found, idVendor=046d, idProduct=c03e usb 1-5.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5.2: Product: USB-PS/2 Optical Mouse usb 1-5.2: Manufacturer: Logitech usb 1-5.2: configuration #1 chosen from 1 choice input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:1a.7/usb1/1-5/1-5.2/1-5.2:1.0/input/input21 generic-usb 0003:046D:C03E.0012: input,hidraw1: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1a.7-5.2/input0 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (01c0) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (01c0) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.1/input0, status -71 usb 1-5: clear tt 1 (01b0) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (01c0) error -71 usb 1-5: USB disconnect, address 26 usb 1-5.1: USB disconnect, address 27 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (01c0) error -19 usb 1-5.2: USB disconnect, address 28 usb 1-5: new high speed USB device using ehci_hcd and address 29 usb 1-5: New USB device found, idVendor=0409, idProduct=0058 usb 1-5: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5: Product: USB2.0 Hub Controller usb 1-5: Manufacturer: NEC Corporation usb 1-5: configuration #1 chosen from 1 choice hub 1-5:1.0: USB hub found hub 1-5:1.0: 4 ports detected usb 1-5.1: new low speed USB device using ehci_hcd and address 30 usb 1-5.1: New USB device found, idVendor=413c, idProduct=2003 usb 1-5.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5.1: Product: Dell USB Keyboard usb 1-5.1: Manufacturer: Dell usb 1-5.1: configuration #1 chosen from 1 choice input: Dell Dell USB Keyboard as /devices/pci0000:00/0000:00:1a.7/usb1/1-5/1-5.1/1-5.1:1.0/input/input22 generic-usb 0003:413C:2003.0013: input,hidraw0: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-0000:00:1a.7-5.1/input0 usb 1-5.2: new low speed USB device using ehci_hcd and address 31 usb 1-5.2: New USB device found, idVendor=046d, idProduct=c03e usb 1-5.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5.2: Product: USB-PS/2 Optical Mouse usb 1-5.2: Manufacturer: Logitech usb 1-5.2: configuration #1 chosen from 1 choice input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:1a.7/usb1/1-5/1-5.2/1-5.2:1.0/input/input23 generic-usb 0003:046D:C03E.0014: input,hidraw1: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1a.7-5.2/input0 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (01f0) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.1/input0, status -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (01e0) error -71 usb 1-5: clear tt 1 (01f0) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (01f0) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (01f0) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.1/input0, status -71 usb 1-5: USB disconnect, address 29 usb 1-5.1: USB disconnect, address 30 usb 1-5: clear tt 1 (01e0) error -71 usb 1-5.2: USB disconnect, address 31 usb 1-5: new high speed USB device using ehci_hcd and address 32 usb 1-5: New USB device found, idVendor=0409, idProduct=0058 usb 1-5: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5: Product: USB2.0 Hub Controller usb 1-5: Manufacturer: NEC Corporation usb 1-5: configuration #1 chosen from 1 choice hub 1-5:1.0: USB hub found hub 1-5:1.0: 4 ports detected usb 1-5.1: new low speed USB device using ehci_hcd and address 33 usb 1-5.1: New USB device found, idVendor=413c, idProduct=2003 usb 1-5.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5.1: Product: Dell USB Keyboard usb 1-5.1: Manufacturer: Dell usb 1-5.1: configuration #1 chosen from 1 choice input: Dell Dell USB Keyboard as /devices/pci0000:00/0000:00:1a.7/usb1/1-5/1-5.1/1-5.1:1.0/input/input24 generic-usb 0003:413C:2003.0015: input,hidraw0: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-0000:00:1a.7-5.1/input0 usb 1-5.2: new low speed USB device using ehci_hcd and address 34 usb 1-5.2: New USB device found, idVendor=046d, idProduct=c03e usb 1-5.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5.2: Product: USB-PS/2 Optical Mouse usb 1-5.2: Manufacturer: Logitech usb 1-5.2: configuration #1 chosen from 1 choice input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:1a.7/usb1/1-5/1-5.2/1-5.2:1.0/input/input25 generic-usb 0003:046D:C03E.0016: input,hidraw1: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1a.7-5.2/input0 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (0220) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.1/input0, status -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (0210) error -71 usb 1-5: clear tt 1 (0220) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (0220) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (0220) error -71 usb 1-5: USB disconnect, address 32 usb 1-5.1: USB disconnect, address 33 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.1/input0, status -108 usb 1-5.2: USB disconnect, address 34 usb 1-5: new high speed USB device using ehci_hcd and address 35 usb 1-5: New USB device found, idVendor=0409, idProduct=0058 usb 1-5: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5: Product: USB2.0 Hub Controller usb 1-5: Manufacturer: NEC Corporation usb 1-5: configuration #1 chosen from 1 choice hub 1-5:1.0: USB hub found hub 1-5:1.0: 4 ports detected usb 1-5.1: new low speed USB device using ehci_hcd and address 36 usb 1-5.1: New USB device found, idVendor=413c, idProduct=2003 usb 1-5.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5.1: Product: Dell USB Keyboard usb 1-5.1: Manufacturer: Dell usb 1-5.1: configuration #1 chosen from 1 choice input: Dell Dell USB Keyboard as /devices/pci0000:00/0000:00:1a.7/usb1/1-5/1-5.1/1-5.1:1.0/input/input26 generic-usb 0003:413C:2003.0017: input,hidraw0: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-0000:00:1a.7-5.1/input0 usb 1-5.2: new low speed USB device using ehci_hcd and address 37 usb 1-5.2: New USB device found, idVendor=046d, idProduct=c03e usb 1-5.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5.2: Product: USB-PS/2 Optical Mouse usb 1-5.2: Manufacturer: Logitech usb 1-5.2: configuration #1 chosen from 1 choice input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:1a.7/usb1/1-5/1-5.2/1-5.2:1.0/input/input27 generic-usb 0003:046D:C03E.0018: input,hidraw1: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1a.7-5.2/input0 zsh[31421]: segfault at 7fff271adda8 ip 0000003af00355c1 sp 00007fff271addb0 error 6 in libc-2.11.1.so[3af0000000+16f000] zsh[31476]: segfault at 7fffc0333be8 ip 0000003af00355c1 sp 00007fffc0333bf0 error 6 in libc-2.11.1.so[3af0000000+16f000] drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (0250) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.1/input0, status -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (0240) error -71 usb 1-5: clear tt 1 (0250) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (0250) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (0250) error -71 usb 1-5: USB disconnect, address 35 usb 1-5.1: USB disconnect, address 36 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.1/input0, status -108 usb 1-5.2: USB disconnect, address 37 usb 1-5: new high speed USB device using ehci_hcd and address 38 usb 1-5: New USB device found, idVendor=0409, idProduct=0058 usb 1-5: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5: Product: USB2.0 Hub Controller usb 1-5: Manufacturer: NEC Corporation usb 1-5: configuration #1 chosen from 1 choice hub 1-5:1.0: USB hub found hub 1-5:1.0: 4 ports detected usb 1-5.1: new low speed USB device using ehci_hcd and address 39 usb 1-5.1: New USB device found, idVendor=413c, idProduct=2003 usb 1-5.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5.1: Product: Dell USB Keyboard usb 1-5.1: Manufacturer: Dell usb 1-5.1: configuration #1 chosen from 1 choice input: Dell Dell USB Keyboard as /devices/pci0000:00/0000:00:1a.7/usb1/1-5/1-5.1/1-5.1:1.0/input/input28 generic-usb 0003:413C:2003.0019: input,hidraw0: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-0000:00:1a.7-5.1/input0 usb 1-5.2: new low speed USB device using ehci_hcd and address 40 usb 1-5.2: New USB device found, idVendor=046d, idProduct=c03e usb 1-5.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5.2: Product: USB-PS/2 Optical Mouse usb 1-5.2: Manufacturer: Logitech usb 1-5.2: configuration #1 chosen from 1 choice input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:1a.7/usb1/1-5/1-5.2/1-5.2:1.0/input/input29 generic-usb 0003:046D:C03E.001A: input,hidraw1: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1a.7-5.2/input0 ata3.00: exception Emask 0x10 SAct 0x0 SErr 0x4000000 action 0xe frozen ata3.00: irq_stat 0x00000040, connection status changed ata3: SError: { DevExch } ata3.00: cmd ec/00:01:00:00:00/00:00:00:00:00/00 tag 0 pio 512 in res 50/00:00:00:00:00/00:00:00:00:00/00 Emask 0x10 (ATA bus error) ata3.00: status: { DRDY } ata3: hard resetting link ata3: SATA link down (SStatus 0 SControl 300) ata3: hard resetting link ata3: SATA link down (SStatus 0 SControl 300) ata3: limiting SATA link speed to 1.5 Gbps ata3: hard resetting link ata3: SATA link down (SStatus 0 SControl 310) ata3.00: disabled ata3: EH complete ata3.00: detaching (SCSI 2:0:0:0) sd 2:0:0:0: [sdb] Synchronizing SCSI cache sd 2:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK sd 2:0:0:0: [sdb] Stopping disk sd 2:0:0:0: [sdb] START_STOP FAILED sd 2:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK sh[13738]: segfault at 0 ip (null) sp 00007fffca741d68 error 14 in bash[400000+cc000] sh[13740]: segfault at 0 ip (null) sp 00007fffa2ff2f18 error 14 in bash[400000+cc000] sh[13743]: segfault at 0 ip (null) sp 00007ffffb0727e8 error 14 in bash[400000+cc000] sh[13746]: segfault at 0 ip (null) sp 00007fff9305f218 error 14 in bash[400000+cc000] sh[13761]: segfault at 0 ip (null) sp 00007fff66834ea8 error 14 in bash[400000+cc000] sh[13764]: segfault at 0 ip (null) sp 00007fff86f1cf38 error 14 in bash[400000+cc000] sh[13766]: segfault at 0 ip (null) sp 00007fff1353d3d8 error 14 in bash[400000+cc000] sh[13768]: segfault at 0 ip (null) sp 00007fffc0c96228 error 14 in bash[400000+cc000] sh[13770]: segfault at 0 ip (null) sp 00007fffd1a09dd8 error 14 in bash[400000+cc000] sh[13772]: segfault at 0 ip (null) sp 00007fffcc072698 error 14 in bash[400000+cc000] sh[13782]: segfault at 0 ip (null) sp 00007fffecb75268 error 14 in bash[400000+cc000] sh[13784]: segfault at 0 ip (null) sp 00007fff161cbe48 error 14 in bash[400000+cc000] sh[13790]: segfault at 0 ip (null) sp 00007ffffe18c288 error 14 in bash[400000+cc000] sh[13792]: segfault at 0 ip (null) sp 00007fff93857af8 error 14 in bash[400000+cc000] sh[13794]: segfault at 0 ip (null) sp 00007fff1c01e878 error 14 in bash[400000+cc000] sh[13796]: segfault at 0 ip (null) sp 00007fffc53078f8 error 14 in bash[400000+cc000] sh[13799]: segfault at 0 ip (null) sp 00007fff3aaba3e8 error 14 in bash[400000+cc000] sh[13801]: segfault at 0 ip (null) sp 00007fff2083ffd8 error 14 in bash[400000+cc000] sh[13811]: segfault at 0 ip (null) sp 00007fff74824c08 error 14 in bash[400000+cc000] sh[13819]: segfault at 0 ip (null) sp 00007fff515dc398 error 14 in bash[400000+cc000] sh[13824]: segfault at 0 ip (null) sp 00007fff624b1f38 error 14 in bash[400000+cc000] sh[13826]: segfault at 0 ip (null) sp 00007fffef5b5708 error 14 in bash[400000+cc000] sh[13828]: segfault at 0 ip (null) sp 00007fffc8bde198 error 14 in bash[400000+cc000] sh[13830]: segfault at 0 ip (null) sp 00007fff52ac6e18 error 14 in bash[400000+cc000] sh[13832]: segfault at 0 ip (null) sp 00007fff4512e958 error 14 in bash[400000+cc000] sh[13835]: segfault at 0 ip (null) sp 00007fff01f3a698 error 14 in bash[400000+cc000] sh[13839]: segfault at 0 ip (null) sp 00007fff9bc1ccb8 error 14 in bash[400000+cc000] sh[13841]: segfault at 0 ip (null) sp 00007fff1f36a398 error 14 in bash[400000+cc000] sh[13843]: segfault at 0 ip (null) sp 00007fff2592e118 error 14 in bash[400000+cc000] sh[13845]: segfault at 0 ip (null) sp 00007fff7536bdc8 error 14 in bash[400000+cc000] __ratelimit: 1 callbacks suppressed sh[13849]: segfault at 0 ip (null) sp 00007fff5dc5b958 error 14 in bash[400000+cc000] sh[13851]: segfault at 0 ip (null) sp 00007fffd7beb038 error 14 in bash[400000+cc000] sh[13854]: segfault at 0 ip (null) sp 00007fffa1af1738 error 14 in bash[400000+cc000] sh[13860]: segfault at 0 ip (null) sp 00007fff0bad0718 error 14 in bash[400000+cc000] ls[13863]: segfault at 0 ip (null) sp 00007fffc0d07328 error 14 in ls[400000+18000] rm[13868]: segfault at 0 ip (null) sp 00007fff322b5278 error 14 in rm[400000+d000] drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (0280) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.1/input0, status -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (0270) error -71 usb 1-5: clear tt 1 (0280) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (0280) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (0280) error -71 usb 1-5: USB disconnect, address 38 usb 1-5.1: USB disconnect, address 39 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.1/input0, status -108 usb 1-5.2: USB disconnect, address 40 usb 1-5: new high speed USB device using ehci_hcd and address 41 usb 1-5: New USB device found, idVendor=0409, idProduct=0058 usb 1-5: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5: Product: USB2.0 Hub Controller usb 1-5: Manufacturer: NEC Corporation usb 1-5: configuration #1 chosen from 1 choice hub 1-5:1.0: USB hub found hub 1-5:1.0: 4 ports detected usb 1-5.1: new low speed USB device using ehci_hcd and address 42 usb 1-5.1: New USB device found, idVendor=413c, idProduct=2003 usb 1-5.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5.1: Product: Dell USB Keyboard usb 1-5.1: Manufacturer: Dell usb 1-5.1: configuration #1 chosen from 1 choice input: Dell Dell USB Keyboard as /devices/pci0000:00/0000:00:1a.7/usb1/1-5/1-5.1/1-5.1:1.0/input/input30 generic-usb 0003:413C:2003.001B: input,hidraw0: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-0000:00:1a.7-5.1/input0 usb 1-5.2: new low speed USB device using ehci_hcd and address 43 usb 1-5.2: New USB device found, idVendor=046d, idProduct=c03e usb 1-5.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5.2: Product: USB-PS/2 Optical Mouse usb 1-5.2: Manufacturer: Logitech usb 1-5.2: configuration #1 chosen from 1 choice input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:1a.7/usb1/1-5/1-5.2/1-5.2:1.0/input/input31 generic-usb 0003:046D:C03E.001C: input,hidraw1: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1a.7-5.2/input0 zsh[22764]: segfault at 7fff32369828 ip 0000003af00355c1 sp 00007fff32369830 error 6 in libc-2.11.1.so[3af0000000+16f000] drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (02b0) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.1/input0, status -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (02a0) error -71 usb 1-5: clear tt 1 (02b0) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (02b0) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (02b0) error -71 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.1/input0, status -71 usb 1-5: clear tt 1 (02a0) error -71 usb 1-5: USB disconnect, address 41 usb 1-5.1: USB disconnect, address 42 drivers/hid/usbhid/hid-core.c: can't reset device, 0000:00:1a.7-5.2/input0, status -71 usb 1-5: clear tt 1 (02b0) error -19 usb 1-5.2: USB disconnect, address 43 usb 1-5: new high speed USB device using ehci_hcd and address 44 usb 1-5: New USB device found, idVendor=0409, idProduct=0058 usb 1-5: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5: Product: USB2.0 Hub Controller usb 1-5: Manufacturer: NEC Corporation usb 1-5: configuration #1 chosen from 1 choice hub 1-5:1.0: USB hub found hub 1-5:1.0: 4 ports detected usb 1-5.1: new low speed USB device using ehci_hcd and address 45 usb 1-5.1: New USB device found, idVendor=413c, idProduct=2003 usb 1-5.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5.1: Product: Dell USB Keyboard usb 1-5.1: Manufacturer: Dell usb 1-5.1: configuration #1 chosen from 1 choice input: Dell Dell USB Keyboard as /devices/pci0000:00/0000:00:1a.7/usb1/1-5/1-5.1/1-5.1:1.0/input/input32 generic-usb 0003:413C:2003.001D: input,hidraw0: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-0000:00:1a.7-5.1/input0 usb 1-5.2: new low speed USB device using ehci_hcd and address 46 usb 1-5.2: New USB device found, idVendor=046d, idProduct=c03e usb 1-5.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-5.2: Product: USB-PS/2 Optical Mouse usb 1-5.2: Manufacturer: Logitech usb 1-5.2: configuration #1 chosen from 1 choice input: Logitech USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:1a.7/usb1/1-5/1-5.2/1-5.2:1.0/input/input33 generic-usb 0003:046D:C03E.001E: input,hidraw1: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1a.7-5.2/input0 So here's the question: is it possible to get /dev/sdb back without rebooting?