I get the following errors when I turn on my external hard drive enclosure: ------------------------------------------------------------------ ieee1394: got invalid ack 11 from node 65472 (tcode 4) ieee1394: got invalid ack 11 from node 65472 (tcode 4) ieee1394: got invalid ack 11 from node 65472 (tcode 4) ieee1394: ConfigROM quadlet transaction error for node 0-00:1023 ieee1394: Node changed: 0-00:1023 -> 0-01:1023 ------------------------------------------------------------------ sbp2 does *not* get loaded automatically.
If I unload ohci1394 and reload it, I get: ------------------------------------------------------------------ ieee1394: ConfigROM quadlet transaction error for node 0-00:1023 ohci1394: $Rev: 1097 $ Ben Collins bcollins@debian.org ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[9] MMIO=[d0202000-d02027ff] Max Packet=[2048] ieee1394: Node added: ID:BUS[0-00:1023] GUID[005077350710020e] ieee1394: Host added: ID:BUS[0-01:1023] GUID[08004603015ea68f] ieee1394: unsolicited response packet received - no tlabel match sbp2: $Rev: 1096 $ Ben Collins bcollins@debian.org ieee1394: sbp2: Driver forced to serialize I/O (serialize_io = 1) scsi1 : SCSI emulation for IEEE-1394 SBP-2 Devices ieee1394: sbp2: sbp2_firmware_revision = 100102 ------------------------------------------------------------------- Still no drive detected, until I attempt to mount a partition:
ieee1394: sbp2: Logged into SBP-2 device ieee1394: sbp2: Node 0-00:1023: Max speed [S400] - Max payload [2048] Vendor: ST312002 Model: 2A Rev: Type: Direct-Access ANSI SCSI revision: 06 SCSI device sdb: 234467403 512-byte hdwr sectors (120047 MB) sdb: asking for cache data failed sdb: assuming drive cache: write through sdb:<3>ieee1394: sbp2: aborting sbp2 command Read (10) 00 0d f9 b0 48 00 00 03 00 ieee1394: sbp2: aborting sbp2 command Test Unit Ready 00 00 00 00 00 ieee1394: sbp2: reset requested ieee1394: sbp2: Generating sbp2 fetch agent reset ieee1394: sbp2: aborting sbp2 command Test Unit Ready 00 00 00 00 00 ieee1394: sbp2: reset requested ieee1394: sbp2: Generating sbp2 fetch agent reset eth1: New link status: Disconnected (0002) eth1: New link status: Connected (0001) ieee1394: sbp2: aborting sbp2 command Test Unit Ready 00 00 00 00 00 ieee1394: sbp2: reset requested ieee1394: sbp2: Generating sbp2 fetch agent reset
What is the status of firewire support on FC2-devel? It is quite worrying it seems to be retrogressing ever since 2.4.21 was released (first requiring rescan-scsi-bus.sh, and now this). Is there any possibility of shipping a 2.4 kernel in addition to 2.6 for FC2 final?
Hardware's Sony Vaio Z1MP, Centrino (Pentium-M 1.3GHz) with a USB memory stick interface.
Relevant lsmod lines: sbp2 27656 0 ohci1394 41860 0 sd_mod 16928 0 usb_storage 65984 0 scsi_mod 124600 4 sbp2,sg,sd_mod,usb_storage
Has anyone run into a similar problem? Bugzilla has nothing to say on that - I'll probably file a report tomorrow.
Thanks,
- Michel
On Feb 17, 2004, "Michel Alexandre Salim" salimma@fastmail.fm wrote:
What is the status of firewire support on FC2-devel?
I had some minor issues with 2.6.1-1.65 that prevented it from recognizing my Maxtor 5000DV early in the boot (I had mkinitrd --with=sd_mod --with=sbp2, such that I could do RAID 1 to the external disk), but those were all fixed in 2.6.2.