[fedora-arm] Odroid-HC1 won't boot

On 12/4/18 1:24 PM, Dennis Gilmore wrote: No success today.  Here is what I tried: used https://blog.christophersmart.com/2018/04/28/fedora-on-odroid-hc1-mini-na... All work was done on my F28 x64 notebook on to a 16GB uSD card. downloaded and installed F30 minimal: fedora-arm-image-installer --image=/home/rgm/arm/Fedora-Minimal-armhfp-Rawhide-20181203.n.0-sda.raw.xz --target=none --media=/dev/sdb Then installed the bootloader: mkdir hardkernel ; cd hardkernel wget https://raw.githubusercontent.com/hardkernel/u-boot/odroidxu4-v2017.05/sd... \ https://raw.githubusercontent.com/hardkernel/u-boot/odroidxu4-v2017.05/sd... \ https://raw.githubusercontent.com/hardkernel/u-boot/odroidxu4-v2017.05/sd... \ https://raw.githubusercontent.com/hardkernel/u-boot/odroidxu4-v2017.05/sd... cp /run/media/rgm/__/usr/share/uboot/odroid-xu3/u-boot.bin . chmod a+x sd_fusing.sh ./sd_fusing.sh /dev/sdb Note that I took the uboot from the F30 install. Next I fixed extlinux.  The above website had extlinux.conf directly in the mounted boot partition, I found it in the extlinux directory. sed -i "s|append|& cpuidle.off=1 \ console=tty1 console=ttySAC2,115200n8 \ rd.driver.pre=ledtrig-heartbeat,xhci-plat-hcd no_bL_switcher|" \ /run/media/rgm/__boot/extlinux/extlinux.conf This resulted in: cat /run/media/rgm/__boot/extlinux/extlinux.conf # extlinux.conf generated by appliance-creator ui menu.c32 menu autoboot Welcome to Fedora-Minimal-armhfp-Rawhide-20181203.n.0. Automatic boot in # second{,s}. Press a key for options. menu title Fedora-Minimal-armhfp-Rawhide-20181203.n.0 Boot Options. menu hidden timeout 20 totaltimeout 600 label Fedora-Minimal-armhfp-Rawhide-20181203.n.0 (4.20.0-0.rc4.git2.1.fc30.armv7hl)     kernel /vmlinuz-4.20.0-0.rc4.git2.1.fc30.armv7hl     append cpuidle.off=1 console=tty1 console=ttySAC2,115200n8 rd.driver.pre=ledtrig-heartbeat,xhci-plat-hcd no_bL_switcher ro root=UUID=0405755f-001a-4df5-8a6d-c9538ca89ee3 rhgb quiet LANG=en_US.UTF-8     fdtdir /dtb-4.20.0-0.rc4.git2.1.fc30.armv7hl/     initrd /initrd-4.20.0-0.rc4.git2.1.fc30.armv7hl.img I inserted the uSD card in the Odroid, connected the serial cable, running screen and here is the capture: U-Boot 2018.09 (Sep 11 2018 - 09:51:41 +0000) for ODROID-XU3/XU4/HC1 CPU:   Exynos5422 @ 800 MHz Model: Odroid XU3 based on EXYNOS5422 Board: Odroid XU3 based on EXYNOS5422 Type:  hc1 DRAM:  2 GiB MMC:   EXYNOS DWMMC: 0, EXYNOS DWMMC: 2 Loading Environment from MMC... Card did not respond to voltage select! *** Warning - No block device, using default environment In:    serial Out:   serial Err:   serial Net:   No ethernet found. Hit any key to stop autoboot:  0 MMC Device 1 not found no mmc device at slot 1 Card did not respond to voltage select! switch to partitions #0, OK mmc2 is current device Scanning mmc 2:2... Found /extlinux/extlinux.conf Retrieving file: /extlinux/extlinux.conf 728 bytes read in 3 ms (236.3 KiB/s) Ignoring unknown command: ui Ignoring malformed menu command:  autoboot Ignoring malformed menu command:  hidden Ignoring unknown command: totaltimeout Fedora-Minimal-armhfp-Rawhide-20181203.n.0 Boot Options. 1:    Fedora-Minimal-armhfp-Rawhide-20181203.n.0 (4.20.0-0.rc4.git2.1.fc30.arm v7hl) Enter choice: 1:    Fedora-Minimal-armhfp-Rawhide-20181203.n.0 (4.20.0-0.rc4 .git2.1.fc30.armv7hl) Retrieving file: /initrd-4.20.0-0.rc4.git2.1.fc30.armv7hl.img ** File not found /initrd-4.20.0-0.rc4.git2.1.fc30.armv7hl.img ** Skipping Fedora-Minimal-armhfp-Rawhide-20181203.n.0 (4.20.0-0.rc4.git2.1.fc30.ar mv7hl) for failure retrieving initrd SCRIPT FAILED: continuing... starting USB... USB0:   USB EHCI 1.00 USB1:   Register 2000140 NbrPorts 2 Starting the controller USB XHCI 1.00 USB2:   Register 2000140 NbrPorts 2 Starting the controller USB XHCI 1.00 scanning bus 0 for devices... 1 USB Device(s) found scanning bus 1 for devices... cannot reset port 1!? 1 USB Device(s) found scanning bus 2 for devices... 2 USB Device(s) found        scanning usb for storage devices... 0 Storage Device(s) found        scanning usb for ethernet devices... 1 Ethernet Device(s) found Waiting for Ethernet connection... done. BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 BOOTP broadcast 4 BOOTP broadcast 5 BOOTP broadcast 6 Retry time exceeded; starting again missing environment variable: pxeuuid Retrieving file: /extlinux/pxelinux.cfg/00000000 *** ERROR: `serverip' not set Retrieving file: /extlinux/pxelinux.cfg/0000000 *** ERROR: `serverip' not set ====================== So what am I missing here? Do you have to run the Hardkernel script on an arm boot? Please advise.  Thanks