Eth0 not active at startup
by Bob Latham
Hi,
I am almost a complete newbie to Linux and I apologise for asking about
something very dumb right away.
I want to use Fedora to run a couple of network sockets on two networks
with Samba shares and a simple FTP server - that's all.
I'm having problems trying to set a static IP address on eth0. I can get
it to work but it has to be "activated" by hand each time I start the
machine. There is an option "Activate device when computer starts" but
although ticked, it appears to do nothing.
What am I doing wrong?
Cheers,
Bob.
16 years, 1 month
Transmission Q, That is if I can change the subject here folks
by Gene Heskett
Greetings;
I just fired up 'transmission' because someone has managed to royally screw up
ktorrents screen handling. Its working, but even though I checked the 'ask
where to put it" box, it ignored it, and it is still putting it in my home
directory instead of the directory I normally download this stuff to. I can
fix that after its done, but why should I have to?
--
Cheers, Gene
"There are four boxes to be used in defense of liberty:
soap, ballot, jury, and ammo. Please use in that order."
-Ed Howdershelt (Author)
Rules for Academic Deans:
(1) HIDE!!!!
(2) If they find you, LIE!!!!
-- Father Damian C. Fandal
16 years, 1 month
pilot and palm sync
by Zoltan Kota
Hi,
I have just got a Palm Z22. I would like to use it with jpilot under
F8 with the latest updates. I set the device to 'usb:' in jpilot. It
seems to work as root but not with a normal user! Some permissions?
What should I check?
Thanks.
Zoltan
16 years, 1 month
Re: Eth0 not active at startup
by Bob Latham
"Patrick O'Callaghan" <pocallaghan(a)gmail.com> wrote:
> Because in F9 the network is managed by Network Manager (and Network
> Manager Dispatcher) which is a different set of scripts. Presumably the
> OP's NM config wasn't set up to manage the eth0 interface.
> If you click on the System->Administration->Services menu in Gnome,
> you'll see NM at the top and network farther down. It's OK to use one or
> the other, just don't mix them.
When I examined the above I found that..
NetworkManager on
NetworkManagerDispatche off
network off
I wasn't sure what to do so I tried...
Christopher Mocock <chris(a)wavestore.com> wrote:
> I had the same problem the other day and a helpful poster informed me
> that I had to run:
> chkconfig network on
[snip]
> Anyway, that did the trick for me.
Yes, it fixed mine too. I then looked and found it had switched on
"network" in the above. I don't know if just switching that on would have
done the trick.
Thanks everyone for your help. I expect I'll be back soon with another
problem.
Cheers,
Bob.
16 years, 1 month
Java + Firefox
by Timothy Murphy
Should the Firefox Java plugin work with Fedora-8 IcedTea Java?
Does anyone have it working?
Is there some setting one has to make?
16 years, 1 month
USB selective suspend/resume in kernel 2.6.24
by Ambrogio De Lorenzo
Hi all,
I would like to know if the 2.6.24.xx kernels from official repos have
this option enabled
USB selective suspend/resume and wakeup (EXPERIMENTAL)
I found it activated into the 2.6.23.14-115
maybe my problems are related to that options... I don't know
Bye
Ambrogio
16 years, 1 month
setting time zone in redhat bugzilla
by Milos Jakubicek
Hi all,
maybe it is a stupid question and I just didn't notice something, but:
Is there any way, how to setup a different time zone than EST in Redhat
bugzilla? (Even UTC would be better...:)
Thanks for pointing to the right place, if there is any,
Milos
16 years, 1 month
VIA vt6410 IDE controller not activating
by Gus Wirth
I have an add-in PCI card for my PC that contains a VIA vt6410 IDE
controller chip which is used to provide two additional IDE headers to
allow connection of up to four IDE devices. The controller is not
activating with Fedora 8 (32-bit) and kernel 2.6.24.4-64. The system is
fully updated. Does anyone know what I need to do to get this controller
card to work?
According to my research, support for the vt6410 was introduced in the
2.6.15 kernel <http://kernelnewbies.org/Linux_2_6_15> but it seems that
the driver required a via82cxxx chipset to be present. This is not
appropriate because the vt6410 can be obtained as a separate plug-in
card and used with any chipset. My testing results (below) seem to show
that support broke hard with kernel 2.6.21 and the changeover in libata.
Current system is an ECS 755-A2 motherboard with an SiS 755 chipset and
Sempron processor. There is an IDE drive configured as master on channel
1 of the card (known good, tested on another system). I installed
viaideinfo using yum and get the following results when I run it:
[gus@falcon ~]$ sudo viaideinfo
Password:
----------VIA BusMastering IDE Configuration----------------
viaideinfo Version: 0.5
South Bridge: VIA vt6410 Rev 0x6 (PCI 00:0a.0)
IDE Controller: Rev 0x6 (PCI 00:0a.0)
Highest DMA rate: UDMA133
BM-DMA base: 0xe800
PCI clock: 33.3MHz
Master Read Cycle IRDY: 0ws
Master Write Cycle IRDY: 0ws
BM IDE Status Register Read Retry: yes
Max DRDY Pulse Width: No limit
-----------------------Primary IDE-------Secondary IDE------
Read DMA FIFO flush: yes yes
End Sector FIFO flush: no no
Prefetch Buffer: yes yes
Post Write Buffer: yes yes
Enabled: no no
Simplex only: yes yes
Cable Type: 80w 80w
-------------------drive0----drive1----drive2----drive3-----
Transfer Mode: DMA DMA DMA DMA
Address Setup: 120ns 120ns 120ns 120ns
Cmd Active: 360ns 360ns 360ns 360ns
Cmd Recovery: 210ns 210ns 210ns 210ns
Data Active: 330ns 330ns 330ns 330ns
Data Recovery: 270ns 270ns 270ns 270ns
Cycle Time: 600ns 600ns 600ns 600ns
Transfer Rate: 3.3MB/s 3.3MB/s 3.3MB/s 3.3MB/s
The vt6410 card is detected properly at bootup by the BIOS and also
appears in the output of lspci:
[gus@falcon ~]$ lspci|grep -i via
00:0a.0 RAID bus controller: VIA Technologies, Inc. VT6410 ATA133 RAID
controller (rev 06)
dmesg shows the following (heavily edited to show only controller stuff):
SCSI subsystem initialized
Driver 'sd' needs updating - please use bus_type methods
libata version 3.00 loaded.
pata_sis 0000:00:02.5: version 0.5.2
scsi0 : pata_sis
scsi1 : pata_sis
ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x4000 irq 14
ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x4008 irq 15
ata1.00: ATA-6: IC35L060AVV207-0, V22OA66A, max UDMA/100
ata1.00: 120103200 sectors, multi 16: LBA48
ata1.00: configured for UDMA/100
ata2.01: ATAPI: Optiarc DVD RW AD-7190A, 1.01, max UDMA/66
ata2.01: configured for UDMA/66
scsi 0:0:0:0: Direct-Access ATA IC35L060AVV207-0 V22O PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 120103200 512-byte hardware sectors (61493 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 0:0:0:0: [sda] 120103200 512-byte hardware sectors (61493 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sda: sda1 sda2 < sda5 sda6 sda7 sda8 sda9 >
sd 0:0:0:0: [sda] Attached SCSI disk
scsi 1:0:1:0: CD-ROM Optiarc DVD RW AD-7190A 1.01 PQ: 0 ANSI: 5
ACPI: PCI Interrupt 0000:00:0d.0[A] -> GSI 19 (level, low) -> IRQ 21
scsi2 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
<Adaptec 2940 SCSI adapter>
aic7870: Single Channel A, SCSI Id=7, 16/253 SCBs
sd 0:0:0:0: Attached scsi generic sg0 type 0
scsi 1:0:1:0: Attached scsi generic sg1 type 5
Driver 'sr' needs updating - please use bus_type methods
sr0: scsi3-mmc drive: 48x/12x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:1:0: Attached scsi CD-ROM sr0
pata_via 0000:00:0a.0: version 0.3.3
sata_sis 0000:00:05.0: version 1.0
sata_sis 0000:00:05.0: Detected SiS 180/181/964 chipset in SATA mode
scsi3 : sata_sis
scsi4 : sata_sis
ata3: SATA max UDMA/133 cmd 0xe300 ctl 0xe400 bmdma 0xe700 irq 20
ata4: SATA max UDMA/133 cmd 0xe500 ctl 0xe600 bmdma 0xe708 irq 20
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: ATA-7: ST3500630A, 3.AAE, max UDMA/100
ata3.00: 976773168 sectors, multi 16: LBA48
ata3.00: applying bridge limits
ata3.00: configured for UDMA/100
ata4: SATA link down (SStatus 0 SControl 300)
scsi 3:0:0:0: Direct-Access ATA ST3500630A 3.AA PQ: 0 ANSI: 5
sd 3:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
sd 3:0:0:0: [sdb] Write Protect is off
sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sd 3:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
sd 3:0:0:0: [sdb] Write Protect is off
sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sdb: sdb1
sd 3:0:0:0: [sdb] Attached SCSI disk
sd 3:0:0:0: Attached scsi generic sg2 type 0
It seems that the appropriate modules are loading:
[gus@falcon ~]$ lsmod|grep ata
sata_sis 9797 1
pata_via 12357 0
pata_sis 14405 7 sata_sis
pata_acpi 8641 0
ata_generic 8773 0
libata 128561 5
sata_sis,pata_via,pata_sis,pata_acpi,ata_generic
scsi_mod 123341 7
sr_mod,sg,usb_storage,aic7xxx,scsi_transport_spi,libata,sd_mod
I have done some additional experiments with another motherboard and
additional kernels. The other motherboard is a Jetway 663AS Ultra that
uses the VIA KT133A chipset (VT8363A, VT82C686B) with an Athlon 1.4Ghz
processor.
Fedora Core 6 initial install before updates, kernel 2.6.18-1.2798,
output of dmesg (edited):
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:07.1
PCI: VIA IRQ fixup for 0000:00:07.1, from 255 to 0
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt6410 (rev 06) IDE UDMA133 controller on pci0000:00:07.1
ide0: BM-DMA at 0x9000-0x9007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x9008-0x900f, BIOS settings: hdc:pio, hdd:DMA
Probing IDE interface ide0...
hda: IC35L060AVV207-0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdd: SONY DVD RW DW-Q28A, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
VP_IDE: IDE controller at PCI slot 0000:00:09.0
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKB] -> GSI 11 (level,
low) -> IRQ
11
VP_IDE: chipset revision 6
VP_IDE: VIA vt6410 (rev 06) IDE UDMA133 controller on pci0000:00:09.0
VP_IDE: 100% native mode on irq 11
ide2: BM-DMA at 0xbc00-0xbc07, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0xbc08-0xbc0f, BIOS settings: hdg:pio, hdh:pio
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide2...
Probing IDE interface ide3...
hda: max request size: 512KiB
hda: 120103200 sectors (61492 MB) w/1821KiB Cache, CHS=16383/255/63,
UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 < hda5 hda6 hda7 >
Fedora Core 5 after updates to kernel 2.6.20-1.2320
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:07.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt6410 (rev 06) IDE UDMA133 controller on pci0000:00:07.1
ide0: BM-DMA at 0x9000-0x9007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x9008-0x900f, BIOS settings: hdc:pio, hdd:DMA
Probing IDE interface ide0...
hda: IC35L060AVV207-0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdd: SONY DVD RW DW-Q28A, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
VP_IDE: IDE controller at PCI slot 0000:00:09.0
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKB] -> GSI 11 (level,
low) -> IRQ 11
VP_IDE: chipset revision 6
VP_IDE: VIA vt6410 (rev 06) IDE UDMA133 controller on pci0000:00:09.0
VP_IDE: 100% native mode on irq 11
ide2: BM-DMA at 0xbc00-0xbc07, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0xbc08-0xbc0f, BIOS settings: hdg:pio, hdh:pio
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide2...
Probing IDE interface ide3...
hda: max request size: 512KiB
hda: 120103200 sectors (61492 MB) w/1821KiB Cache,
CHS=16383/255/63<6>hda: hw_config=600b
, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 < hda5 hda6 hda7 >
Fedora 7 KDE Live kernel-2.6.21-1.3194.fc7
SCSI subsystem initialized
libata version 2.20 loaded.
pata_via 0000:00:07.1: version 0.2.1
ata1: PATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x00019000
irq 14
ata2: PATA max UDMA/133 cmd 0x00010170 ctl 0x00010376 bmdma 0x00019008
irq 15
scsi0 : pata_via
ata1.00: ata_hpa_resize 1: sectors = 120103200, hpa_sectors = 120103200
ata1.00: ATA-6: IC35L060AVV207-0, V22OA63A, max UDMA/100
ata1.00: 120103200 sectors, multi 16: LBA48
ata1.00: ata_hpa_resize 1: sectors = 120103200, hpa_sectors = 120103200
ata1.00: configured for UDMA/100
scsi1 : pata_via
ata2.01: ATAPI, max UDMA/66
input: ImExPS/2 Generic Explorer Mouse as /class/input/input2
ata2.01: configured for UDMA/33
scsi 0:0:0:0: Direct-Access ATA IC35L060AVV207-0 V22O PQ: 0 ANSI: 5
scsi 1:0:1:0: CD-ROM SONY DVD RW DW-Q28A KYS3 PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:1:0: Attached scsi CD-ROM sr0
SCSI device sda: 120103200 512-byte hdwr sectors (61493 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
SCSI device sda: 120103200 512-byte hdwr sectors (61493 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sda: sda1 sda2 < sda5 sda6 sda7 >
sd 0:0:0:0: Attached scsi disk sda
ISO 9660 Extensions: Microsoft Joliet Level 3
And for a final comparison, the output of Knoppix 5.1.1, kernel 2.6.19
SCSI subsystem initialized
libata version 2.00 loaded.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:07.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt6410 (rev 06) IDE UDMA133 controller on pci0000:00:07.1
ide0: BM-DMA at 0xc000-0xc007, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xc008-0xc00f, BIOS settings: hdc:pio, hdd:DMA
Probing IDE interface ide0...
Probing IDE interface ide1...
hdd: SONY CD-ROM CDU5232, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
VP_IDE: IDE controller at PCI slot 0000:00:09.0
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKB] -> GSI 11 (level,
low) -> IRQ 11
VP_IDE: chipset revision 6
VP_IDE: VIA vt6410 (rev 06) IDE UDMA133 controller on pci0000:00:09.0
VP_IDE: 100% native mode on irq 11
ide2: BM-DMA at 0xe800-0xe807, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0xe808-0xe80f, BIOS settings: hdg:pio, hdh:pio
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide0...
Probing IDE interface ide2...
Probing IDE interface ide3...
hdd: ATAPI 40X CD-ROM drive, 96kB Cache
Uniform CD-ROM driver Revision: 3.20
16 years, 1 month
low power tv
by Tom Poe
www.ubnt.com offers Nanostation2 "radio" that creates wireless cloud up
to 15 kilometers. That sounds like the perfect way to broadcast live
interactive tv shows (think neighborhood videoconferencing). Anyone
doing this with Fedora operating system and whatever other software needed?
Tom
16 years, 1 month
DI-LB604 load balancing router and /etc/resolv.conf
by Frank Cox
I now have my load balancing router up and running on two modems, one cable
modem and one DSL. So far, it seems to be doing what it's supposed to be
doing.
(For folks who remember my earlier questions regarding this matter, I did try
to order that Xincom router but after much fiddling about was eventually told
that it is out of stock. However, this Dlink DI-LB604 is supposed to do the
same thing. It was also $30 cheaper.)
I have a question about /etc/resolv.conf in relation to this setup.
Each of my two ISPs have two nameservers for customer use. For the sake of
demonstration, let's say that ISP A has nameserver 1.1.1.1 and 2.2.2.2 while
ISP B has nameservers 3.3.3.3 and 4.4.4.4
Now, the name of my internal network is melvilletheatre.net.
My /etc/resolv.conf from when I was using only one single ISP and a regular
(single WAN) router was as follows:
search melvilletheatre.net
nameserver 1.1.1.1
nameserver 2.2.2.2
When I set up this dual router, I changed /etc/resolv.conf to this:
search melvilletheatre.net
nameserver 1.1.1.1
nameserver 3.3.3.3
nameserver 2.2.2.2
nameserver 4.4.4.4
This seems to be working at the moment, but I know of at least one problem.
"man resolv.conf" tells me that there can be a maximum of three nameserver
entries so I assume that the 4.4.4.4 entry is being ignored.
My question is, is there a better way to set this up? In addition to load
balancing this router also does failover, so if one of my connections goes down
things are supposed to keep chugging along anyway using the other connection.
It seems like this would be another factor in properly
configuring /etc/resolv.conf because as it is now if ISP A drops then I think I
have only one working nameserver entry left in /etc/resolv.conf at that time.
--
MELVILLE THEATRE ~ Melville Sask ~ http://www.melvilletheatre.com
16 years, 1 month
