7:49 p.m.
Hi --
Installed fc9 on a server from fc8 and had a scsi controller Adaptec
29160 Ultra160 SCSI adapter
give me grief. It's used with an lto autochanger. When I entered:
mtx -d /dev/changer status
(/dev/changer a symlink to /dev/sg6)
It hung for a while, (a huge listing follows, sorry about this), then
kernel messages gallor.
Anyway I tried reseating the card, moving the card to an alternate
slot, checking the cabling, reboot the autochanger,
reboot the system --all did _not_ help.
I pulled the card and replaced it with a Adaptec AIC-7892A U160/m (rev
02) and the autochanger and lto drive worked.
I also had to swap cables because of the interface differences.
Long story, but can anyone say that this card looks broken? It has a 5
year warranty and would like to get it replaced if so. Or is
it a driver issue/I couldn't find a direct hit searching the web or in
the archives?
I think my head is still sore from banging it against the autochanger!
Thanks for _any_ help!
-- Gary
Sep 27 10:30:15 genepi1 kernel: scsi5 : Adaptec AIC79XX PCI-X SCSI HBA
DRIVER, Rev 3.0
Sep 27 10:30:15 genepi1 kernel: <Adaptec 29320ALP PCIx Ultra320
SCSI adapter>
Sep 27 10:30:15 genepi1 kernel: aic7901: Ultra320 Wide Channel
A, SCSI Id=7, PCI-X 101-133Mhz, 512 SCBs
Sep 27 10:30:15 genepi1 kernel: ACPI: PCI Interrupt 0000:04:01.0[A] ->
GSI 16 (level, low) -> IRQ 16
Sep 27 10:30:15 genepi1 kernel: e1000: 0000:04:01.0: e1000_probe:
(PCI:66MHz:32-bit) 00:0e:0c:d9:8d:54
Sep 27 10:30:15 genepi1 kernel: scsi 5:0:1:0: Sequential-Access HP
Ultrium 4-SCSI B12H PQ: 0 ANSI: 5
Sep 27 10:30:15 genepi1 kernel: scsi target5:0:1: asynchronous
Sep 27 10:30:15 genepi1 kernel: scsi5:A:1:0: Tagged Queuing enabled. Depth 4
Sep 27 10:30:15 genepi1 kernel: scsi target5:0:1: Beginning Domain Validation
Sep 27 10:30:15 genepi1 kernel: scsi target5:0:1: wide asynchronous
Sep 27 10:30:15 genepi1 kernel: scsi target5:0:1: FAST-160 WIDE SCSI
320.0 MB/s DT IU RTI PCOMP (6.25 ns, offset 64)
Sep 27 10:30:15 genepi1 kernel: scsi target5:0:1: Domain Validation
skipping write tests
Sep 27 10:30:15 genepi1 kernel: scsi target5:0:1: Ending Domain Validation
Sep 27 10:30:15 genepi1 kernel: scsi 5:0:1:1: Medium Changer
OVERLAND NEO Series 0504 PQ: 0 ANSI: 5
Sep 27 10:30:15 genepi1 kernel: scsi5:A:1:1: Tagged Queuing enabled. Depth 4
Sep 27 10:30:15 genepi1 kernel: e1000: eth2: e1000_probe: Intel(R)
PRO/1000 Network Connection
Sep 27 10:30:15 genepi1 kernel: device-mapper: uevent: version 1.0.3
Sep 27 10:30:15 genepi1 kernel: device-mapper: ioctl: 4.13.0-ioctl
(2007-10-18) initialised: dm-devel(a)redhat.com
Sep 27 10:30:15 genepi1 kernel: device-mapper: multipath: version 1.0.5 loaded
Sep 27 10:30:15 genepi1 kernel: EXT3 FS on sda1, internal journal
Sep 27 10:30:15 genepi1 kernel: Adding 25165812k swap on /dev/sda2.
Priority:-1 extents:1 across:25165812k
Sep 27 10:30:15 genepi1 kernel: firmware: requesting intel-ucode/06-0f-06
Sep 27 10:30:15 genepi1 kernel: firmware: requesting intel-ucode/06-0f-06
Sep 27 10:30:15 genepi1 kernel: firmware: requesting intel-ucode/06-0f-06
Sep 27 10:30:15 genepi1 kernel: firmware: requesting intel-ucode/06-0f-06
Sep 27 10:30:15 genepi1 kernel: IA-32 Microcode Update Driver: v1.14a
<tigran(a)aivazian.fsnet.co.uk>
Sep 27 10:30:15 genepi1 kernel: microcode: CPU0 updated from revision
0x44 to 0xcd, date = 09162007
Sep 27 10:30:15 genepi1 kernel: microcode: CPU1 updated from revision
0x44 to 0xcd, date = 09162007
Sep 27 10:30:15 genepi1 kernel: microcode: CPU2 updated from revision
0x44 to 0xcd, date = 09162007
Sep 27 10:30:15 genepi1 kernel: microcode: CPU3 updated from revision
0x44 to 0xcd, date = 09162007
Sep 27 10:30:15 genepi1 kernel: scsi 5:0:1:0: Attached scsi generic sg5 type 1
Sep 27 10:30:15 genepi1 kernel: scsi 5:0:1:1: Attached scsi generic sg6 type 8
Sep 27 10:30:15 genepi1 kernel: osst :I: Tape driver with OnStream
support version 0.99.4
Sep 27 10:30:15 genepi1 kernel: osst :I: $Id: osst.c,v 1.73 2005/01/01
21:13:34 wriede Exp $
Sep 27 10:30:15 genepi1 kernel: Driver 'osst' needs updating - please
use bus_type methods
Sep 27 10:30:15 genepi1 kernel: st: Version 20080224, fixed bufsize
32768, s/g segs 256
Sep 27 10:30:15 genepi1 kernel: Driver 'st' needs updating - please
use bus_type methods
Sep 27 10:30:15 genepi1 kernel: st 5:0:1:0: Attached scsi tape st0
Sep 27 10:30:15 genepi1 kernel: st 5:0:1:0: st0: try direct i/o: yes
(alignment 4 B)
Sep 27 10:30:15 genepi1 kernel: eth0: Link is Up 1000 Mbps Full
Duplex, Flow Control: RX
Sep 27 10:30:15 genepi1 kernel: ADDRCONF(NETDEV_CHANGE): eth0: link
becomes ready
Sep 27 10:30:15 genepi1 kernel: ADDRCONF(NETDEV_UP): eth1: link is not ready
Sep 27 10:54:58 genepi1 yum: Installed: mtx-1.3.12-1.fc9.x86_64
Sep 27 10:58:19 genepi1 kernel: 3w-9xxx: scsi4: ERROR: (0x03:0x010D):
Invalid field in CDB:.
Sep 27 10:58:19 genepi1 kernel: 3w-9xxx: scsi4: ERROR: (0x03:0x0101):
Invalid command opcode:opcode=0xB8.
Sep 27 10:58:19 genepi1 kernel: 3w-9xxx: scsi4: ERROR: (0x03:0x0101):
Invalid command opcode:opcode=0xB8.
Sep 27 11:02:27 genepi1 kernel: st 5:0:1:0: Attempting to queue an
ABORT message:CDB: 0x12 0x0 0x0 0x0 0x38 0x0
Sep 27 11:02:27 genepi1 kernel: scsi5: At time of recovery, card was not paused
Sep 27 11:02:27 genepi1 kernel:
>>>>>>>>>>>>>>>>>> Dump Card State
Begins <<<<<<<<<<<<<<<<<
Sep 27 11:02:27 genepi1 kernel: scsi5: Dumping Card State at program
address 0x34 Mode 0x22
Sep 27 11:02:27 genepi1 kernel: Card was paused
Sep 27 11:02:27 genepi1Sep 27 11:02:27 genepi1 kernel: INTSTAT[0x0]
SELOID[0x1] SELID[0x10] HS_MAILBOX[0x0]
Sep 27 11:02:27 genepi1 kernel: INTCTL[0x80] SEQINTSTAT[0x0]
SAVED_MODE[0x11] DFFSTAT[0x33]
Sep 27 11:02:27 genepi1 kernel: SCSISIGI[0x0] SCSIPHASE[0x0]
SCSIBUS[0x0] LASTPHASE[0x1]
Sep 27 11:02:27 genepi1 kernel: SCSISEQ0[0x0] SCSISEQ1[0x12]
SEQCTL0[0x0] SEQINTCTL[0x0]
Sep 27 11:02:27 genepi1 kernel: SEQ_FLAGS[0x0] SEQ_FLAGS2[0x4]
QFREEZE_COUNT[0x7]
Sep 27 11:02:27 genepi1 kernel: KERNEL_QFREEZE_COUNT[0x6] MK_MESSAGE_SCB[0xff00]
Sep 27 11:02:27 genepi1 kernel: MK_MESSAGE_SCSIID[0xff] SSTAT0[0x0] SSTAT1[0x8]
Sep 27 11:02:27 genepi1 kernel: SSTAT2[0x0] SSTAT3[0x0] PERRDIAG[0x0]
SIMODE1[0xa4]
Sep 27 11:02:27 genepi1 kernel: LQISTAT0[0x0] LQISTAT1[0x0]
LQISTAT2[0x0] LQOSTAT0[0x0]
Sep 27 11:02:27 genepi1 kernel: LQOSTAT1[0x0] LQOSTAT2[0xe1]
Sep 27 11:02:27 genepi1 kernel:
Sep 27 11:02:27 genepi1 kernel: SCB Count = 4 CMDS_PENDING = 0 LASTSCB
0xffff CURRSCB 0x3 NEXTSCB 0xff80
Sep 27 11:02:27 genepi1 kernel: qinstart = 44 qinfifonext = 46
Sep 27 11:02:27 genepi1 kernel: QINFIFO: 0x3 0x2
Sep 27 11:02:27 genepi1 kernel: WAITING_TID_QUEUES:
Sep 27 11:02:27 genepi1 kernel: Pending list:
Sep 27 11:02:27 genepi1 kernel: 2 FIFO_USE[0x0] SCB_CONTROL[0x68]
SCB_SCSIID[0x17]
Sep 27 11:02:27 genepi1 kernel: 3 FIFO_USE[0x2] SCB_CONTROL[0x68]
SCB_SCSIID[0x17]
Sep 27 11:02:27 genepi1 kernel: Total 2
Sep 27 11:02:27 genepi1 kernel: Kernel Free SCB list: 1 0
Sep 27 11:02:27 genepi1 kernel: Sequencer Complete DMA-inprog list:
Sep 27 11:02:27 genepi1 kernel: Sequencer Complete list:
Sep 27 11:02:27 genepi1 kernel: Sequencer DMA-Up and Complete list:
Sep 27 11:02:27 genepi1 kernel: Sequencer On QFreeze and Complete list:
Sep 27 11:02:27 genepi1 kernel:
Sep 27 11:02:27 genepi1 kernel:
Sep 27 11:02:27 genepi1 kernel: scsi5: FIFO0 Free, LONGJMP == 0x82a3, SCB 0x3
Sep 27 11:02:27 genepi1 kernel: SEQIMODE[0x3f] SEQINTSRC[0x0]
DFCNTRL[0x0] DFSTATUS[0x89]
Sep 27 11:02:27 genepi1 kernel: SG_CACHE_SHADOW[0x2] SG_STATE[0x0]
DFFSXFRCTL[0x0]
Sep 27 11:02:27 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5] SHADDR =
0x00, SHCNT = 0x0
Sep 27 11:02:27 genepi1 kernel: HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]
Sep 27 11:02:27 genepi1 kernel:
Sep 27 11:02:27 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP == 0x8063, SCB 0x3
Sep 27 11:02:27 genepi1 kernel: SEQIMODE[0x3f] SEQINTSRC[0x0]
DFCNTRL[0x0] DFSTATUS[0x89]
Sep 27 11:02:27 genepi1 kernel: SG_CACHE_SHADOW[0x2] SG_STATE[0x0]
DFFSXFRCTL[0x0]
Sep 27 11:02:27 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5] SHADDR =
0x00, SHCNT = 0x0
Sep 27 11:02:27 genepi1 kernel: HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]
Sep 27 11:02:27 genepi1 kernel: LQIN: 0x8 0x0 0x0 0x3 0x0 0x1 0x0 0x0
0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
Sep 27 11:02:27 genepi1 kernel: scsi5: LQISTATE = 0x0, LQOSTATE = 0x0,
OPTIONMODE = 0x52
Sep 27 11:02:27 genepi1 kernel: scsi5: OS_SPACE_CNT = 0x20 MAXCMDCNT = 0x1
Sep 27 11:02:27 genepi1 kernel: scsi5: SAVED_SCSIID = 0x0 SAVED_LUN = 0x0
Sep 27 11:02:27 genepi1 kernel: SIMODE0[0xc]
Sep 27 11:02:27 genepi1 kernel: CCSCBCTL[0x0]
Sep 27 11:02:27 genepi1 kernel: scsi5: REG0 == 0x3, SINDEX = 0x104,
DINDEX = 0x104
Sep 27 11:02:27 genepi1 kernel: scsi5: SCBPTR == 0x3, SCB_NEXT ==
0xff80, SCB_NEXT2 == 0xff80
Sep 27 11:02:27 genepi1 kernel: CDB 3 0 0 83 a 8c
Sep 27 11:02:27 genepi1 kernel: STACK: 0x20 0x0 0x0 0x0 0x0 0x0 0x0 0x0
Sep 27 11:02:27 genepi1 kernel:
<<<<<<<<<<<<<<<<< Dump Card State Ends
>>>>>>>>>>>>>>>>>
Sep 27 11:02:27 genepi1 kernel: scsi5:0:1:0: Cmd aborted from QINFIFO
Sep 27 11:02:37 genepi1 kernel: st 5:0:1:0: Attempting to queue an
ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
Sep 27 11:02:37 genepi1 kernel: scsi5: At time of recovery, card was not paused
Sep 27 11:02:37 genepi1 kernel:
>>>>>>>>>>>>>>>>>> Dump Card State
Begins <<<<<<<<<<<<<<<<<
Sep 27 11:02:37 genepi1 kernel: scsi5: Dumping Card State at program
address 0x18 Mode 0x33
kernel: INTSTAT[0x0] SELOID[0x1] SELID[0x10] HS_MAILBOX[0x0]
Sep 27 11:02:27 genepi1 kernel: INTCTL[0x80] SEQINTSTAT[0x0]
SAVED_MODE[0x11] DFFSTAT[0x33]
Sep 27 11:02:37 genepi1 kernel:
>>>>>>>>>>>>>>>>>> Dump Card State
Begins <<<<<<<<<<<<<<<<<
Sep 27 11:02:37 genepi1 kernel: scsi5: Dumping Card State at program
address 0x18 Mode 0x33
Sep 27 11:02:37 genepi1 kernel: Card was paused
Sep 27 11:02:37 genepi1 kernel: INTSTAT[0x0] SELOID[0x1] SELID[0x10]
HS_MAILBOX[0x0]
Sep 27 11:02:37 genepi1 kernel: INTCTL[0x80] SEQINTSTAT[0x0]
SAVED_MODE[0x11] DFFSTAT[0x33]
Sep 27 11:02:37 genepi1 kernel: SCSISIGI[0x0] SCSIPHASE[0x0]
SCSIBUS[0x0] LASTPHASE[0x1]
Sep 27 11:02:37 genepi1 kernel: SCSISEQ0[0x0] SCSISEQ1[0x12]
SEQCTL0[0x0] SEQINTCTL[0x0]
Sep 27 11:02:37 genepi1 kernel: SEQ_FLAGS[0x0] SEQ_FLAGS2[0x4]
QFREEZE_COUNT[0x7]
Sep 27 11:02:37 genepi1 kernel: KERNEL_QFREEZE_COUNT[0x6] MK_MESSAGE_SCB[0xff00]
Sep 27 11:02:37 genepi1 kernel: MK_MESSAGE_SCSIID[0xff] SSTAT0[0x0] SSTAT1[0x0]
Sep 27 11:02:37 genepi1 kernel: SSTAT2[0x0] SSTAT3[0x0] PERRDIAG[0x0]
SIMODE1[0xa4]
Sep 27 11:02:37 genepi1 kernel: LQISTAT0[0x0] LQISTAT1[0x0]
LQISTAT2[0x0] LQOSTAT0[0x0]
Sep 27 11:02:37 genepi1 kernel: LQOSTAT1[0x0] LQOSTAT2[0xe1]
Sep 27 11:02:37 genepi1 kernel:
Sep 27 11:02:37 genepi1 kernel: SCB Count = 4 CMDS_PENDING = 0 LASTSCB
0xffff CURRSCB 0x3 NEXTSCB 0xff80
Sep 27 11:02:37 genepi1 kernel: qinstart = 44 qinfifonext = 46
Sep 27 11:02:37 genepi1 kernel: QINFIFO: 0x3 0x2
Sep 27 11:02:37 genepi1 kernel: WAITING_TID_QUEUES:
Sep 27 11:02:37 genepi1 kernel: Pending list:
Sep 27 11:02:37 genepi1 kernel: 2 FIFO_USE[0x0] SCB_CONTROL[0x68]
SCB_SCSIID[0x17]
Sep 27 11:02:37 genepi1 kernel: 3 FIFO_USE[0x2] SCB_CONTROL[0x68]
SCB_SCSIID[0x17]
Sep 27 11:02:37 genepi1 kernel: Total 2
Sep 27 11:02:37 genepi1 kernel: Kernel Free SCB list: 1 0
Sep 27 11:02:37 genepi1 kernel: Sequencer Complete DMA-inprog list:
Sep 27 11:02:37 genepi1 kernel: Sequencer Complete list:
Sep 27 11:02:37 genepi1 kernel: Sequencer DMA-Up and Complete list:
Sep 27 11:02:37 genepi1 kernel: Sequencer On QFreeze and Complete list:
Sep 27 11:02:37 genepi1 kernel:
Sep 27 11:02:37 genepi1 kernel:
Sep 27 11:02:37 genepi1 kernel: scsi5: FIFO0 Free, LONGJMP == 0x82a3, SCB 0x3
Sep 27 11:02:37 genepi1 kernel: SEQIMODE[0x3f] SEQINTSRC[0x0]
DFCNTRL[0x0] DFSTATUS[0x89]
Sep 27 11:02:37 genepi1 kernel: SG_CACHE_SHADOW[0x2] SG_STATE[0x0]
DFFSXFRCTL[0x0]
Sep 27 11:02:37 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5] SHADDR =
0x00, SHCNT = 0x0
Sep 27 11:02:37 genepi1 kernel: HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]
Sep 27 11:02:37 genepi1 kernel:
Sep 27 11:02:37 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP == 0x8063, SCB 0x3
Sep 27 11:02:37 genepi1 kernel: SEQIMODE[0x3f] SEQINTSRC[0x0]
DFCNTRL[0x0] DFSTATUS[0x89]
Sep 27 11:02:37 genepi1 kernel: SG_CACHE_SHADOW[0x2] SG_STATE[0x0]
DFFSXFRCTL[0x0]
Sep 27 11:02:37 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5] SHADDR =
0x00, SHCNT = 0x0
Sep 27 11:02:37 genepi1 kernel: HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]
Sep 27 11:02:37 genepi1 kernel: LQIN: 0x8 0x0 0x0 0x3 0x0 0x1 0x0 0x0
0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
Sep 27 11:02:37 genepi1 kernel: scsi5: LQISTATE = 0x0, LQOSTATE = 0x0,
OPTIONMODE = 0x52
Sep 27 11:02:37 genepi1 kernel: scsi5: OS_SPACE_CNT = 0x20 MAXCMDCNT = 0x1
Sep 27 11:02:37 genepi1 kernel: scsi5: SAVED_SCSIID = 0x0 SAVED_LUN = 0x0
Sep 27 11:02:37 genepi1 kernel: SIMODE0[0xc]
Sep 27 11:02:37 genepi1 kernel: CCSCBCTL[0x0]
Sep 27 11:02:37 genepi1 kernel: scsi5: REG0 == 0xffff, SINDEX = 0x104,
DINDEX = 0x104
Sep 27 11:02:37 genepi1 kernel: scsi5: SCBPTR == 0x3, SCB_NEXT ==
0xff80, SCB_NEXT2 == 0xff80
Sep 27 11:02:37 genepi1 kernel: CDB 3 0 0 83 a 8c
Sep 27 11:02:37 genepi1 kernel: STACK: 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
Sep 27 11:02:37 Sep 27 11:02:37 genepi1 kernel: scsi5:0:1:0: Cmd
aborted from QINFIFO
Sep 27 11:02:37 genepi1 kernel: scsi 5:0:1:1: Attempting to queue an
ABORT message:CDB: 0x1a 0x8 0x1d 0x0 0x88 0x0
Sep 27 11:02:37 genepi1 kernel: scsi5: At time of recovery, card was not paused
Sep 27 11:02:37 genepi1 kernel:
>>>>>>>>>>>>>>>>>> Dump Card State
Begins <<<<<<<<<<<<<<<<<
Sep 27 11:02:37 genepi1 kernel: scsi5: Dumping Card State at program
address 0x31 Mode 0x11
Sep 27 11:02:37 genepi1 kernel: Card was paused
Sep 27 11:02:37 genepi1 kernel: INTSTAT[0x0] SELOID[0x1] SELID[0x10]
HS_MAILBOX[0x0]
Sep 27 11:02:37 genepi1 kernel: INTCTL[0x80] SEQINTSTAT[0x0]
SAVED_MODE[0x11] DFFSTAT[0x33]
Sep 27 11:02:37 genepi1 kernel: SCSISIGI[0x0] SCSIPHASE[0x0]
SCSIBUS[0x0] LASTPHASE[0x1]
Sep 27 11:02:37 genepi1 kernel: SCSISEQ0[0x0] SCSISEQ1[0x12]
SEQCTL0[0x0] SEQINTCTL[0x0]
Sep 27 11:02:37 genepi1 kernel: SEQ_FLAGS[0x0] SEQ_FLAGS2[0x4]
QFREEZE_COUNT[0x7]
Sep 27 11:02:37 genepi1 kernel: KERNEL_QFREEZE_COUNT[0x6] MK_MESSAGE_SCB[0xff00]
Sep 27 11:02:37 genepi1 kernel: MK_MESSAGE_SCSIID[0xff] SSTAT0[0x0] SSTAT1[0x0]
Sep 27 11:02:37 genepi1 kernel: SSTAT2[0x0] SSTAT3[0x0] PERRDIAG[0x0]
SIMODE1[0xa4]
Sep 27 11:02:37 genepi1 kernel: LQISTAT0[0x0] LQISTAT1[0x0]
LQISTAT2[0x0] LQOSTAT0[0x0]
Sep 27 11:02:37 genepi1 kernel: LQOSTAT1[0x0] LQOSTAT2[0xe1]
Sep 27 11:02:37 genepi1 kernel:
Sep 27 11:02:37 genepi1 kernel: SCB Count = 4 CMDS_PENDING = 0 LASTSCB
0xffff CURRSCB 0x3 NEXTSCB 0xff80
Sep 27 11:02:37 genepi1 kernel: qinstart = 44 qinfifonext = 45
Sep 27 11:02:37 genepi1 kernel: QINFIFO: 0x3
Sep 27 11:02:37 genepi1 kernel: WAITING_TID_QUEUES:
Sep 27 11:02:37 genepi1 kernel: Pending list:
Sep 27 11:02:37 genepi1 kernel: 3 FIFO_USE[0x0] SCB_CONTROL[0x68]
SCB_SCSIID[0x17]
Sep 27 11:02:37 genepi1 kernel: Total 1
Sep 27 11:02:37 genepi1 kernel: Kernel Free SCB list: 2 1 0
Sep 27 11:02:37 genepi1 kernel: Sequencer Complete DMA-inprog list:
Sep 27 11:02:37 genepi1 kernel: Sequencer Complete list:
Sep 27 11:02:37 genepi1 kernel: Sequencer DMA-Up and Complete list:
Sep 27 11:02:37 genepi1 kernel: Sequencer On QFreeze and Complete list:
Sep 27 11:02:37 genepi1 kernel:
Sep 27 11:02:37 genepi1 kernel:
Sep 27 11:02:37 genepi1 kernel: scsi5: FIFO0 Free, LONGJMP == 0x82a3, SCB 0x3
Sep 27 11:02:37 genepi1 kernel: SEQIMODE[0x3f] SEQINTSRC[0x0]
DFCNTRL[0x0] DFSTATUS[0x89]
Sep 27 11:02:37 genepi1 kernel: SG_CACHE_SHADOW[0x2] SG_STATE[0x0]
DFFSXFRCTL[0x0]
Sep 27 11:02:37 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5] SHADDR =
0x00, SHCNT = 0x0
Sep 27 11:02:37 genepi1 kernel: HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]
Sep 27 11:02:37 genepi1 kernel:
Sep 27 11:02:37 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP == 0x8063, SCB 0x3
Sep 27 11:02:37 genepi1 kernel: SEQIMODE[0x3f] SEQINTSRC[0x0]
DFCNTRL[0x0] DFSTATUS[0x89]
Sep 27 11:02:37 genepi1 kernel: SG_CACHE_SHADOW[0x2] SG_STATE[0x0]
DFFSXFRCTL[0x0]
Sep 27 11:02:37 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5] SHADDR =
0x00, SHCNT = 0x0
Sep 27 11:02:37 genepi1 kernel: HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]
Sep 27 11:02:37 genepi1 kernel: LQIN: 0x8 0x0 0x0 0x3 0x0 0x1 0x0 0x0
0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
Sep 27 11:02:37 genepi1 kernel: scsi5: LQISTATE = 0x0, LQOSTATE = 0x0,
OPTIONMODE = 0x52
Sep 27 11:02:37 genepi1 kernel: scsi5: OS_SPACE_CNT = 0x20 MAXCMDCNT = 0x1
Sep 27 11:02:37 genepi1 kernel: scsi5: SAVED_SCSIID = 0x0 SAVED_LUN = 0x0
Sep 27 11:02:37 genepi1 kernel: SIMODE0[0xc]
Sep 27 11:02:37 genepi1 kernel: CCSCBCTL[0x0]
Sep 27 11:02:37 genepi1 kernel: scsi5: REG0 == 0x3, SINDEX = 0x104,
DINDEX = 0x104
Sep 27 11:02:37 genepi1 kernel: scsi5: SCBPTR == 0x3, SCB_NEXT ==
0xff80, SCB_NEXT2 == 0xff80
Sep 27 11:02:37 genepi1 kernel: CDB 3 0 0 83 a 8c
Sep 27 11:02:37 genepi1 kernel: STACK: 0x1f 0x0 0x0 0x0 0x0 0x0 0x0 0x0
Sep 27 11:02:37 genepi1 kernel:
<<<<<<<<<<<<<<<<< Dump Card State Ends
>>>>>>>>>>>>>>>>>
genepi1 kernel: <<<<<<<<<<<<<<<<<
Dump Card State Ends >>>>>>>>>>>>>>>>>
Sep 27 11:02:37 genepi1 kernel: scsi5:0:1:0: Cmd aborted from QINFIFO
Sep 27 11:02:37 genepi1 kernel: scsi 5:0:1:1: Attempting to queue an
ABORT message:CDB: 0x1a 0x8 0x1d 0x0 0x88 0x0
Sep 27 11:02:37 genepi1 kernel: scsi5:0:1:0: Cmd aborted from QINFIFO
Sep 27 11:02:37 genepi1 kernel: scsi 5:0:1:1: Attempting to queue an
ABORT message:CDB: 0x1a 0x8 0x1d 0x0 0x88 0x0
Sep 27 11:02:37 genepi1 kernel: scsi5: At time of recovery, card was not paused
Sep 27 11:02:37 genepi1 kernel:
>>>>>>>>>>>>>>>>>> Dump Card State
Begins <<<<<<<<<<<<<<<<<
Sep 27 11:02:37 genepi1 kernel: scsi5: Dumping Card State at program
address 0x31 Mode 0x11
Sep 27 11:02:37 genepi1 kernel: Card was paused
Sep 27 11:02:37 genepi1 kernel: INTSTAT[0x0] SELOID[0x1] SELID[0x10]
HS_MAILBOX[0x0]
Sep 27 11:02:37 genepi1 kernel: INTCTL[0x80] SEQINTSTAT[0x0]
SAVED_MODE[0x11] DFFSTAT[0x33]
Sep 27 11:02:37 genepi1 kernel: SCSISIGI[0x0] SCSIPHASE[0x0]
SCSIBUS[0x0] LASTPHASE[0x1]
Sep 27 11:02:37 genepi1 kernel: SCSISEQ0[0x0] SCSISEQ1[0x12]
SEQCTL0[0x0] SEQINTCTL[0x0]
Sep 27 11:02:37 genepi1 kernel: SEQ_FLAGS[0x0] SEQ_FLAGS2[0x4]
QFREEZE_COUNT[0x7]
Sep 27 11:02:37 genepi1 kernel: KERNEL_QFREEZE_COUNT[0x6] MK_MESSAGE_SCB[0xff00]
Sep 27 11:02:37 genepi1 kernel: MK_MESSAGE_SCSIID[0xff] SSTAT0[0x0] SSTAT1[0x0]
Sep 27 11:02:37 genepi1 kernel: SSTAT2[0x0] SSTAT3[0x0] PERRDIAG[0x0]
SIMODE1[0xa4]
Sep 27 11:02:37 genepi1 kernel: LQISTAT0[0x0] LQISTAT1[0x0]
LQISTAT2[0x0] LQOSTAT0[0x0]
Sep 27 11:02:37 genepi1 kernel: LQOSTAT1[0x0] LQOSTAT2[0xe1]
Sep 27 11:02:37 genepi1 kernel:
Sep 27 11:02:37 genepi1 kernel: SCB Count = 4 CMDS_PENDING = 0 LASTSCB
0xffff CURRSCB 0x3 NEXTSCB 0xff80
Sep 27 11:02:37 genepi1 kernel: qinstart = 44 qinfifonext = 45
Sep 27 11:02:37 genepi1 kernel: QINFIFO: 0x3
Sep 27 11:02:37 genepi1 kernel: WAITING_TID_QUEUES:
Sep 27 11:02:37 genepi1 kernel: Pending list:
Sep 27 11:02:37 genepi1 kernel: 3 FIFO_USE[0x0] SCB_CONTROL[0x68]
SCB_SCSIID[0x17]
Sep 27 11:02:37 genepi1 kernel: Total 1
Sep 27 11:02:37 genepi1 kernel: Kernel Free SCB list: 2 1 0
Sep 27 11:02:37 genepi1 kernel: Sequencer Complete DMA-inprog list:
Sep 27 11:02:37 genepi1 kernel: Sequencer Complete list:
Sep 27 11:02:37 genepi1 kernel: Sequencer DMA-Up and Complete list:
Sep 27 11:02:37 genepi1 kernel: Sequencer On QFreeze and Complete list:
Sep 27 11:02:37 genepi1 kernel:
Sep 27 11:02:37 genepi1 kernel:
Sep 27 11:02:37 genepi1 kernel: scsi5: FIFO0 Free, LONGJMP == 0x82a3, SCB 0x3
Sep 27 11:02:37 genepi1 kernel: SEQIMODE[0x3f] SEQINTSRC[0x0]
DFCNTRL[0x0] DFSTATUS[0x89]
Sep 27 11:02:37 genepi1 kernel: SG_CACHE_SHADOW[0x2] SG_STATE[0x0]
DFFSXFRCTL[0x0]
Sep 27 11:02:37 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5] SHADDR =
0x00, SHCNT = 0x0
Sep 27 11:02:37 genepi1 kernel: HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]
Sep 27 11:02:37 genepi1 kernel:
Sep 27 11:02:37 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP == 0x8063, SCB 0x3
Sep 27 11:02:37 genepi1 kernel: SEQIMODE[0x3f] SEQINTSRC[0x0]
DFCNTRL[0x0] DFSTATUS[0x89]
Sep 27 11:02:37 genepi1 kernel: SG_CACHE_SHADOW[0x2] SG_STATE[0x0]
DFFSXFRCTL[0x0]
Sep 27 11:02:37 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5] SHADDR =
0x00, SHCNT = 0x0
Sep 27 11:02:37 genepi1 kernel: HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]
Sep 27 11:02:37 genepi1 kernel: LQIN: 0x8 0x0 0x0 0x3 0x0 0x1 0x0 0x0
0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
Sep 27 11:02:37 genepi1 kernel: scsi5: LQISTATE = 0x0, LQOSTATE = 0x0,
OPTIONMODE = 0x52
Sep 27 11:02:37 genepi1 kernel: scsi5: OS_SPACE_CNT = 0x20 MAXCMDCNT = 0x1
Sep 27 11:02:37 genepi1 kernel: scsi5: SAVED_SCSIID = 0x0 SAVED_LUN = 0x0
Sep 27 11:02:37 genepi1 kernel: SIMODE0[0xc]
Sep 27 11:02:37 genepi1 kernel: CCSCBCTL[0x0]
Sep 27 11:02:37 genepi1 kernel: scsi5: REG0 == 0x3, SINDEX = 0x104,
DINDEX = 0x104
Sep 27 11:02:37 genepi1 kernel: scsi5: SCBPTR == 0x3, SCB_NEXT ==
0xff80, SCB_NEXT2 == 0xff80
Sep 27 11:02:37 genepi1 kernel: CDB 3 0 0 83 a 8c
Sep 27 11:02:37 genepi1 kernel: STACK: 0x1f 0x0 0x0 0x0 0x0 0x0 0x0 0x0
Sep 27 11:02:37 genepi1 kernel:
<<<<<<<<<<<<<<<<< Dump Card State Ends
>>>>>>>>>>>>>>>>>
Sep 27 11:02:37 genepi1 kernel: STACK: 0x1f 0x0 0x0 0x0 0x0 0x0 0x0 0x0
Sep 27 11:02:37 genepi1 kernel:
<<<<<<<<<<<<<<<<< Dump Card State Ends
>>>>>>>>>>>>>>>>>
Sep 27 11:02:37 genepi1 kernel: scsi5:0:1:1: Cmd aborted from QINFIFO
Sep 27 11:02:47 genepi1 kernel: scsi 5:0:1:1: Attempting to queue an
ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
Sep 27 11:02:47 genepi1 kernel: scsi5: At time of recovery, card was not paused
Sep 27 11:02:47 genepi1 kernel:
>>>>>>>>>>>>>>>>>> Dump Card State
Begins <<<<<<<<<<<<<<<<<
Sep 27 11:02:47 genepi1 kernel: scsi5: Dumping Card State at program
address 0x18 Mode 0x33
Sep 27 11:02:47 genepi1 kernel: Card was paused
Sep 27 11:02:47 genepi1 kernel: INTSTAT[0x0] SELOID[0x1] SELID[0x10]
HS_MAILBOX[0x0]
Sep 27 11:02:47 genepi1 kernel: INTCTL[0x80] SEQINTSTAT[0x0]
SAVED_MODE[0x11] DFFSTAT[0x33]
Sep 27 11:02:47 genepi1 kernel: SCSISIGI[0x0] SCSIPHASE[0x0]
SCSIBUS[0x0] LASTPHASE[0x1]
Sep 27 11:02:47 genepi1 kernel: SCSISEQ0[0x0] SCSISEQ1[0x12]
SEQCTL0[0x0] SEQINTCTL[0x0]
Sep 27 11:02:47 genepi1 kernel: SEQ_FLAGS[0x0] SEQ_FLAGS2[0x4]
QFREEZE_COUNT[0x7]
Sep 27 11:02:47 genepi1 kernel: KERNEL_QFREEZE_COUNT[0x6] MK_MESSAGE_SCB[0xff00]
Sep 27 11:02:47 genepi1 kernel: MK_MESSAGE_SCSIID[0xff] SSTAT0[0x0] SSTAT1[0x0]
Sep 27 11:02:47 genepi1 kernel: SSTAT2[0x0] SSTAT3[0x0] PERRDIAG[0x0]
SIMODE1[0xa4]
Sep 27 11:02:47 genepi1 kernel: LQISTAT0[0x0] LQISTAT1[0x0]
LQISTAT2[0x0] LQOSTAT0[0x0]
Sep 27 11:02:47 genepi1 kernel: LQOSTAT1[0x0] LQOSTAT2[0xe1]
Sep 27 11:02:47 genepi1 kernel:
Sep 27 11:02:47 genepi1 kernel: SCB Count = 4 CMDS_PENDING = 0 LASTSCB
0xffff CURRSCB 0x3 NEXTSCB 0xff80
Sep 27 11:02:47 genepi1 kernel: qinstart = 44 qinfifonext = 45
Sep 27 11:02:47 genepi1 kernel: QINFIFO: 0x3
Sep 27 11:02:47 genepi1 kernel: WAITING_TID_QUEUES:
Sep 27 11:02:47 genepi1 kernel: Pending list:
Sep 27 11:02:47 genepi1 kernel: 3 FIFO_USE[0x0] SCB_CONTROL[0x68]
SCB_SCSIID[0x17]
Sep 27 11:02:47 genepi1 kernel: Total 1
Sep 27 11:02:47 genepi1 kernel: Kernel Free SCB list: 2 1 0
Sep 27 11:02:47 genepi1 kernel: Sequencer Complete DMA-inprog list:
Sep 27 11:02:47 genepi1 kernel: Sequencer Complete list:
Sep 27 11:02:47 genepi1 kernel: Sequencer DMA-Up and Complete list:
Sep 27 11:02:47 genepi1 kernel: Sequencer On QFreeze and Complete list:
Sep 27 11:02:47 genepi1 kernel:
Sep 27 11:02:47 genepi1 kernel:
Sep 27 11:02:47 genepi1 kernel: scsi5: FIFO0 Free, LONGJMP == 0x82a3, SCB 0x3
Sep 27 11:02:47 genepi1 kernel: SEQIMODE[0x3f] SEQINTSRC[0x0]
DFCNTRL[0x0] DFSTATUS[0x89]
Sep 27 11:02:47 genepi1 kernel: SG_CACHE_SHADOW[0x2] SG_STATE[0x0]
DFFSXFRCTL[0x0]
Sep 27 11:02:47 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5] SHADDR =
0x00, SHCNT = 0x0
Sep 27 11:02:47 genepi1 kernel: HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]
Sep 27 11:02:47 genepi1 kernel:
Sep 27 11:02:47 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP == 0x8063, SCB 0x3
Sep 27 11:02:47 genepi1 kernel: SEQIMODE[0x3f] SEQINTSRC[0x0]
DFCNTRL[0x0] DFSTATUS[0x89]
Sep 27 11:02:47 genepi1 kernel: SG_CACHE_SHADOW[0x2] SG_STATE[0x0]
DFFSXFRCTL[0x0]
Sep 27 11:02:47 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5] SHADDR =
0x00, SHCNT = 0x0
Sep 27 11:02:47 genepi1 kernel: HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]
Sep 27 11:02:47 genepi1 kernel: LQIN: 0x8 0x0 0x0 0x3 0x0 0x1 0x0 0x0
0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
Sep 27 11:02:47 genepi1 kernel: scsi5: LQISTATE = 0x0, LQOSTATE = 0x0,
OPTIONMODE = 0x52
Sep 27 11:02:47 genepi1 kernel: scsi5: OS_SPACE_CNT = 0x20 MAXCMDCNT = 0x1
Sep 27 11:02:47 genepi1 kernel: scsi5: SAVED_SCSIID = 0x0 SAVED_LUN = 0x0
Sep 27 11:02:47 genepi1 kernel: SIMODE0[0xc]
Sep 27 11:02:47 genepi1 kernel: CCSCBCTL[0x0]
Sep 27 11:02:47 genepi1 kernel: scsi5: REG0 == 0xffff, SINDEX = 0x104,
DINDEX = 0x104
Sep 27 11:02:47 genepi1 kernel: scsi5: SCBPTR == 0x3, SCB_NEXT ==
0xff80, SCB_NEXT2 == 0xff80
Sep 27 11:02:47 genepi1 kernel: CDB 3 0 0 83 a 8c
Sep 27 11:02:47 genepi1 kernel: scsi5: SCBPTR == 0x3, SCB_NEXT ==
0xff80, SCB_NEXT2 == 0xff80
Sep 27 11:02:47 genepi1 kernel: CDB 3 0 0 83 a 8c
Sep 27 11:02:47 genepi1 kernel: STACK: 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
Sep 27 11:02:47 genepi1 kernel:
<<<<<<<<<<<<<<<<< Dump Card State Ends
>>>>>>>>>>>>>>>>>
Sep 27 11:02:47 genepi1 kernel: scsi5:0:1:1: Cmd aborted from QINFIFO
Sep 27 11:02:47 genepi1 kernel: st 5:0:1:0: Attempting to queue a
TARGET RESET message:CDB: 0x12 0x0 0x0 0x0 0x38 0x0
Sep 27 11:02:47 genepi1 kernel: scsi5: Device reset code sleeping
Sep 27 11:02:52 genepi1 kernel: scsi5: Device reset timer expired (active 1)
Sep 27 11:02:52 genepi1 kernel: scsi5: Device reset returning 0x2003
Sep 27 11:02:52 genepi1 kernel: scsi 5:0:1:1: Attempting to queue a
TARGET RESET message:CDB: 0x1a 0x8 0x1d 0x0 0x88 0x0
Sep 27 11:02:52 genepi1 kernel: scsi5: Device reset code sleeping
Sep 27 11:02:57 genepi1 kernel: scsi5: Device reset timer expired (active 1)
Sep 27 11:02:57 genepi1 kernel: scsi5: Device reset returning 0x2003
Sep 27 11:02:57 genepi1 kernel: Recovery SCB completes
Sep 27 11:02:57 genepi1 kernel: Recovery SCB completes
Sep 27 11:03:17 genepi1 kernel: st 5:0:1:0: Attempting to queue an
ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
Sep 27 11:03:17 genepi1 kernel: scsi5: At time of recovery, card was not paused
Sep 27 11:03:17 genepi1 kernel:
>>>>>>>>>>>>>>>>>> Dump Card State
Begins <<<<<<<<<<<<<<<<<
Sep 27 11:03:17 genepi1 kernel: scsi5: Dumping Card State at program
address 0x9 Mode 0x33
Sep 27 11:03:17 genepi1 kernel: Card was paused
Sep 27 11:03:17 genepi1 kernel: INTSTAT[0x0] SELOID[0x1] SELID[0x10]
HS_MAILBOX[0x0]
Sep 27 11:03:17 genepi1 kernel: INTCTL[0x80] SEQINTSTAT[0x0]
SAVED_MODE[0x11] DFFSTAT[0x33]
Sep 27 11:03:17 genepi1 kernel: SCSISIGI[0x0] SCSIPHASE[0x0]
SCSIBUS[0x0] LASTPHASE[0x1]
Sep 27 11:03:17 genepi1 kernel: SCSISEQ0[0x0] SCSISEQ1[0x12]
SEQCTL0[0x0] SEQINTCTL[0x0]
Sep 27 11:03:17 genepi1 kernel: SEQ_FLAGS[0x0] SEQ_FLAGS2[0x4]
QFREEZE_COUNT[0x7]
Sep 27 11:03:17 genepi1 kernel: KERNEL_QFREEZE_COUNT[0x6] MK_MESSAGE_SCB[0xff00]
Sep 27 11:03:17 genepi1 kernel: MK_MESSAGE_SCSIID[0xff] SSTAT0[0x0] SSTAT1[0x0]
Sep 27 11:03:17 genepi1 kernel: SSTAT2[0x0] SSTAT3[0x0] PERRDIAG[0x0]
SIMODE1[0xa4]
Sep 27 11:03:17 genepi1 kernel: LQISTAT0[0x0] LQISTAT1[0x0]
LQISTAT2[0x0] LQOSTAT0[0x0]
Sep 27 11:03:17 genepi1 kernel: LQOSTAT1[0x0] LQOSTAT2[0xe1]
Sep 27 11:03:17 genepi1 kernel:
Sep 27 11:03:17 genepi1 kernel: SCB Count = 4 CMDS_PENDING = 0 LASTSCB
0xffff CURRSCB 0x3 NEXTSCB 0xff80
Sep 27 11:03:17 genepi1 kernel: qinstart = 44 qinfifonext = 45
Sep 27 11:03:17 genepi1 kernel: QINFIFO: 0x2
Sep 27 11:03:17 genepi1 kernel: WAITING_TID_QUEUES:
Sep 27 11:03:17 genepi1 kernel: Pending list:
Sep 27 11:03:17 genepi1 kernel: 2 FIFO_USE[0x0] SCB_CONTROL[0x68]
SCB_SCSIID[0x17]
Sep 27 11:03:17 genepi1 kernel: Total 1
Sep 27 11:03:17 genepi1 kernel: Kernel Free SCB list: 3 1 0
Sep 27 11:03:17 genepi1 kernel: Sequencer Complete DMA-inprog list:
Sep 27 11:03:17 genepi1 kernel: Sequencer Complete list:
Sep 27 11:03:17 genepi1 kernel: Sequencer DMA-Up and Complete list:
Sep 27 11:03:17 genepi1 kernel: Sequencer On QFreeze and Complete list:
Sep 27 11:03:17 genepi1 kernel:
Sep 27 11:03:17 genepi1 kernel:
Sep 27 11:03:17 genepi1 kernel: scsi5: FIFO0 Free, LONGJMP == 0x80a3, SCB 0x3
Sep 27 11:03:17 genepi1 kernel: SEQIMODE[0x3f] SEQINTSRC[0x0]
DFCNTRL[0x0] DFSTATUS[0x89]
Sep 27 11:03:17 genepi1 kernel: SG_CACHE_SHADOW[0x2] SG_STATE[0x0]
DFFSXFRCTL[0x0]
Sep 27 11:03:17 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5] SHADDR =
0x00, SHCNT = 0x0
Sep 27 11:03:17 genepi1 kernel: HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]
Sep 27 11:03:17 genepi1 kernel:
Sep 27 11:03:17 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP == 0x8063, SCB 0x3
Sep 27 11:03:17 genepi1 kernel: SEQIMODE[0x3f] SEQINTSRC[0x0]
DFCNTRL[0x0] DFSTATUS[0x89]
Sep 27 11:03:17 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP == 0x8063, SCB 0x3
Sep 27 11:03:17 genepi1 kernel: SEQIMODE[0x3f] SEQINTSRC[0x0]
DFCNTRL[0x0] DFSTATUS[0x89]
Sep 27 11:03:17 genepi1 kernel: SG_CACHE_SHADOW[0x2] SG_STATE[0x0]
DFFSXFRCTL[0x0]
Sep 27 11:03:17 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5] SHADDR =
0x00, SHCNT = 0x0
Sep 27 11:03:17 genepi1 kernel: HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]
Sep 27 11:03:17 genepi1 kernel: LQIN: 0x8 0x0 0x0 0x3 0x0 0x1 0x0 0x0
0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
Sep 27 11:03:17 genepi1 kernel: scsi5: LQISTATE = 0x0, LQOSTATE = 0x0,
OPTIONMODE = 0x52
Sep 27 11:03:17 genepi1 kernel: scsi5: OS_SPACE_CNT = 0x20 MAXCMDCNT = 0x1
Sep 27 11:03:17 genepi1 kernel: scsi5: SAVED_SCSIID = 0x0 SAVED_LUN = 0x0
Sep 27 11:03:17 genepi1 kernel: SIMODE0[0xc]
Sep 27 11:03:17 genepi1 kernel: CCSCBCTL[0x0]
Sep 27 11:03:17 genepi1 kernel: scsi5: REG0 == 0xffff, SINDEX = 0x104,
DINDEX = 0x104
Sep 27 11:03:17 genepi1 kernel: scsi5: SCBPTR == 0x3, SCB_NEXT ==
0xff80, SCB_NEXT2 == 0xff80
Sep 27 11:03:17 genepi1 kernel: CDB 3 0 0 83 a 8c
Sep 27 11:03:17 genepi1 kernel: STACK: 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
Sep 27 11:03:17 genepi1 kernel:
<<<<<<<<<<<<<<<<< Dump Card State Ends
>>>>>>>>>>>>>>>>>
Sep 27 11:03:17 genepi1 kernel: scsi5:0:1:0: Cmd aborted from QINFIFO
Sep 27 11:03:27 genepi1 kernel: scsi 5:0:1:1: Attempting to queue an
ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
Sep 27 11:03:27 genepi1 kernel: scsi5: At time of recovery, card was not paused
Sep 27 11:03:27 genepi1 kernel:
>>>>>>>>>>>>>>>>>> Dump Card State
Begins <<<<<<<<<<<<<<<<<
Sep 27 11:03:27 genepi1 kernel: scsi5: Dumping Card State at program
address 0x22 Mode 0x33
Sep 27 11:03:27 genepi1 kernel: Card was paused
Sep 27 11:03:27 genepi1 kernel: INTSTAT[0x0] SELOID[0x1] SELID[0x10]
HS_MAILBOX[0x0]
Sep 27 11:03:27 genepi1 kernel: INTCTL[0x80] SEQINTSTAT[0x0]
SAVED_MODE[0x11] DFFSTAT[0x33]
Sep 27 11:03:27 genepi1 kernel: SCSISIGI[0x0] SCSIPHASE[0x0]
SCSIBUS[0x0] LASTPHASE[0x1]
Sep 27 11:03:27 genepi1 kernel: SCSISEQ0[0x0] SCSISEQ1[0x12]
SEQCTL0[0x0] SEQINTCTL[0x0]
Sep 27 11:03:27 genepi1 kernel: SEQ_FLAGS[0x0] SEQ_FLAGS2[0x4]
QFREEZE_COUNT[0x7]
Sep 27 11:03:27 genepi1 kernel: KERNEL_QFREEZE_COUNT[0x6] MK_MESSAGE_SCB[0xff00]
Sep 27 11:03:27 genepi1 kernel: MK_MESSAGE_SCSIID[0xff] SSTAT0[0x0] SSTAT1[0x0]
Sep 27 11:03:27 genepi1 kernel: SSTAT2[0x0] SSTAT3[0x0] PERRDIAG[0x0]
SIMODE1[0xa4]
Sep 27 11:03:27 genepi1 kernel: LQISTAT0[0x0] LQISTAT1[0x0]
LQISTAT2[0x0] LQOSTAT0[0x0]
Sep 27 11:03:27 genepi1 kernel: LQOSTAT1[0x0] LQOSTAT2[0xe1]
Sep 27 11:03:27 genepi1 kernel:
Sep 27 11:03:27 genepi1 kernel: SCB Count = 4 CMDS_PENDING = 0 LASTSCB
0xffff CURRSCB 0x3 NEXTSCB 0xff80
Sep 27 11:03:27 genepi1 kernel: qinstart = 44 qinfifonext = 45
Sep 27 11:03:27 genepi1 kernel: QINFIFO: 0x2
Sep 27 11:03:27 genepi1 kernel: WAITING_TID_QUEUES:
Sep 27 11:03:27 genepi1 kernel: Pending list:
Sep 27 11:03:27 genepi1 kernel: 2 FIFO_USE[0x0] SCB_CONTROL[0x68]
SCB_SCSIID[0x17]
Sep 27 11:03:27 genepi1 kernel: Total 1
Sep 27 11:03:27 genepi1 kernel: Kernel Free SCB list: 3 1 0
Sep 27 11:03:27 genepi1 kernel: Sequencer Complete DMA-inprog list:
Sep 27 11:03:27 genepi1 kernel: Sequencer Complete list:
Sep 27 11:03:27 genepi1 kernel: Sequencer DMA-Up and Complete list:
Sep 27 11:03:27 genepi1 kernel: Sequencer On QFreeze and Complete list:
Sep 27 11:03:27 genepi1 kernel:
Sep 27 11:03:27 genepi1 kernel:
Sep 27 11:03:27 genepi1 kernel: scsi5: FIFO0 Free, LONGJMP == 0x80a3, SCB 0x3
Sep 27 11:03:27 genepi1 kernel: SEQIMODE[0x3f] SEQINTSRC[0x0]
DFCNTRL[0x0] DFSTATUS[0x89]
Sep 27 11:03:27 genepi1 kernel: SG_CACHE_SHADOW[0x2] SG_STATE[0x0]
DFFSXFRCTL[0x0]
Sep 27 11:03:Sep 27 11:03:27 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
CCSGCTL[0x10]
Sep 27 11:03:27 genepi1 kernel:
Sep 27 11:03:27 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP == 0x8063, SCB 0x3
Sep 27 11:03:27 genepi1 kernel: SEQIMODE[0x3f] SEQINTSRC[0x0]
DFCNTRL[0x0] DFSTATUS[0x89]
Sep 27 11:03:27 genepi1 kernel: SG_CACHE_SHADOW[0x2] SG_STATE[0x0]
DFFSXFRCTL[0x0]
Sep 27 11:03:27 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5] SHADDR =
0x00, SHCNT = 0x0
Sep 27 11:03:27 genepi1 kernel: HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]
Sep 27 11:03:27 genepi1 kernel: LQIN: 0x8 0x0 0x0 0x3 0x0 0x1 0x0 0x0
0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
Sep 27 11:03:27 genepi1 kernel: scsi5: LQISTATE = 0x0, LQOSTATE = 0x0,
OPTIONMODE = 0x52
Sep 27 11:03:27 genepi1 kernel: scsi5: OS_SPACE_CNT = 0x20 MAXCMDCNT = 0x1
Sep 27 11:03:27 genepi1 kernel: scsi5: SAVED_SCSIID = 0x0 SAVED_LUN = 0x0
Sep 27 11:03:27 genepi1 kernel: SIMODE0[0xc]
Sep 27 11:03:27 genepi1 kernel: CCSCBCTL[0x0]
Sep 27 11:03:27 genepi1 kernel: scsi5: REG0 == 0xffff, SINDEX = 0x104,
DINDEX = 0x104
Sep 27 11:03:27 genepi1 kernel: scsi5: SCBPTR == 0x3, SCB_NEXT ==
0xff80, SCB_NEXT2 == 0xff80
Sep 27 11:03:27 genepi1 kernel: CDB 3 0 0 83 a 8c
Sep 27 11:03:27 genepi1 kernel: STACK: 0x1e 0x0 0x0 0x0 0x0 0x0 0x0 0x0
Sep 27 11:03:27 genepi1 kernel:
<<<<<<<<<<<<<<<<< Dump Card State Ends
>>>>>>>>>>>>>>>>>
Sep 27 11:03:27 genepi1 kernel: scsi5:0:1:1: Cmd aborted from QINFIFO
Sep 27 11:03:27 genepi1 kernel: st 5:0:1:0: Device offlined - not
ready after error recovery
Sep 27 11:03:27 genepi1 kernel: scsi 5:0:1:1: Device offlined - not
ready after error recovery
Sep 27 11:07:00 genepi1 kernel: 3w-9xxx: scsi4: ERROR: (0x03:0x010D):
Invalid field in CDB:.
Sep 27 11:07:00 genepi1 kernel: 3w-9xxx: scsi4: ERROR: (0x03:0x0101):
Invalid command opcode:opcode=0xB8.
Sep 27 11:07:00 genepi1 kernel: 3w-9xxx: scsi4: ERROR: (0x03:0x0101):
Invalid command opcode:opcode=0xB8.
Sep 27 11:16:41 genepi1 kernel: 3w-9xxx: scsi4: ERROR: (0x03:0x010D):
Invalid field in CDB:.
Sep 27 11:16:41 genepi1 kernel: 3w-9xxx: scsi4: ERROR: (0x03:0x0101):
Invalid command opcode:opcode=0xB8.
Sep 27 11:16:41 genepi1 kernel: 3w-9xxx: scsi4: ERROR: (0x03:0x0101):
Invalid command opcode:opcode=0xB8.
Sep 27 11:16:51 genepi1 kernel: 3w-9xxx: scsi4: ERROR: (0x03:0x010D):
Invalid field in CDB:.
Sep 27 11:16:51 genepi1 kernel: 3w-9xxx: scsi4: ERROR: (0x03:0x0101):
Invalid command opcode:opcode=0xB8.
Sep 27 11:16:51 genepi1 kernel: 3w-9xxx: scsi4: ERROR: (0x03:0x0101):
Invalid command opcode:opcode=0xB8.
27 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5] SHADDR = 0x00, SHCNT = 0x0
Sep 27 11:03:27 genepi1 kernel: HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]
Sep 27 11:03:27 genepi1 kernel:
9:59 p.m.
--- On Tue, 9/30/08, gary artim <gartim(a)gmail.com> wrote:
From: gary artim <gartim(a)gmail.com>
Subject: Adaptec 29160 Ultra160 problem -- Fedora 9 install.
To: fedora-list(a)redhat.com
Date: Tuesday, September 30, 2008, 12:49 AM
Hi --
Installed fc9 on a server from fc8 and had a scsi
controller Adaptec
29160 Ultra160 SCSI adapter
give me grief. It's used with an lto autochanger. When
I entered:
mtx -d /dev/changer status
(/dev/changer a symlink to /dev/sg6)
It hung for a while, (a huge listing follows, sorry about
this), then
kernel messages gallor.
Anyway I tried reseating the card, moving the card to an
alternate
slot, checking the cabling, reboot the autochanger,
reboot the system --all did _not_ help.
I pulled the card and replaced it with a Adaptec AIC-7892A
U160/m (rev
02) and the autochanger and lto drive worked.
I also had to swap cables because of the interface
differences.
Long story, but can anyone say that this card looks broken?
It has a 5
year warranty and would like to get it replaced if so. Or
is
it a driver issue/I couldn't find a direct hit
searching the web or in
the archives?
I think my head is still sore from banging it against the
autochanger!
Thanks for _any_ help!
-- Gary
Sep 27 10:30:15 genepi1 kernel: scsi5 : Adaptec AIC79XX
PCI-X SCSI HBA
DRIVER, Rev 3.0
Sep 27 10:30:15 genepi1 kernel: <Adaptec 29320ALP
PCIx Ultra320
SCSI adapter>
Sep 27 10:30:15 genepi1 kernel: aic7901: Ultra320
Wide Channel
A, SCSI Id=7, PCI-X 101-133Mhz, 512 SCBs
Sep 27 10:30:15 genepi1 kernel: ACPI: PCI Interrupt
0000:04:01.0[A] ->
GSI 16 (level, low) -> IRQ 16
Sep 27 10:30:15 genepi1 kernel: e1000: 0000:04:01.0:
e1000_probe:
(PCI:66MHz:32-bit) 00:0e:0c:d9:8d:54
Sep 27 10:30:15 genepi1 kernel: scsi 5:0:1:0:
Sequential-Access HP
Ultrium 4-SCSI B12H PQ: 0 ANSI: 5
Sep 27 10:30:15 genepi1 kernel: scsi target5:0:1:
asynchronous
Sep 27 10:30:15 genepi1 kernel: scsi5:A:1:0: Tagged Queuing
enabled. Depth 4
Sep 27 10:30:15 genepi1 kernel: scsi target5:0:1: Beginning
Domain Validation
Sep 27 10:30:15 genepi1 kernel: scsi target5:0:1: wide
asynchronous
Sep 27 10:30:15 genepi1 kernel: scsi target5:0:1: FAST-160
WIDE SCSI
320.0 MB/s DT IU RTI PCOMP (6.25 ns, offset 64)
Sep 27 10:30:15 genepi1 kernel: scsi target5:0:1: Domain
Validation
skipping write tests
Sep 27 10:30:15 genepi1 kernel: scsi target5:0:1: Ending
Domain Validation
Sep 27 10:30:15 genepi1 kernel: scsi 5:0:1:1: Medium
Changer
OVERLAND NEO Series 0504 PQ: 0 ANSI: 5
Sep 27 10:30:15 genepi1 kernel: scsi5:A:1:1: Tagged Queuing
enabled. Depth 4
Sep 27 10:30:15 genepi1 kernel: e1000: eth2: e1000_probe:
Intel(R)
PRO/1000 Network Connection
Sep 27 10:30:15 genepi1 kernel: device-mapper: uevent:
version 1.0.3
Sep 27 10:30:15 genepi1 kernel: device-mapper: ioctl:
4.13.0-ioctl
(2007-10-18) initialised: dm-devel(a)redhat.com
Sep 27 10:30:15 genepi1 kernel: device-mapper: multipath:
version 1.0.5 loaded
Sep 27 10:30:15 genepi1 kernel: EXT3 FS on sda1, internal
journal
Sep 27 10:30:15 genepi1 kernel: Adding 25165812k swap on
/dev/sda2.
Priority:-1 extents:1 across:25165812k
Sep 27 10:30:15 genepi1 kernel: firmware: requesting
intel-ucode/06-0f-06
Sep 27 10:30:15 genepi1 kernel: firmware: requesting
intel-ucode/06-0f-06
Sep 27 10:30:15 genepi1 kernel: firmware: requesting
intel-ucode/06-0f-06
Sep 27 10:30:15 genepi1 kernel: firmware: requesting
intel-ucode/06-0f-06
Sep 27 10:30:15 genepi1 kernel: IA-32 Microcode Update
Driver: v1.14a
<tigran(a)aivazian.fsnet.co.uk>
Sep 27 10:30:15 genepi1 kernel: microcode: CPU0 updated
from revision
0x44 to 0xcd, date = 09162007
Sep 27 10:30:15 genepi1 kernel: microcode: CPU1 updated
from revision
0x44 to 0xcd, date = 09162007
Sep 27 10:30:15 genepi1 kernel: microcode: CPU2 updated
from revision
0x44 to 0xcd, date = 09162007
Sep 27 10:30:15 genepi1 kernel: microcode: CPU3 updated
from revision
0x44 to 0xcd, date = 09162007
Sep 27 10:30:15 genepi1 kernel: scsi 5:0:1:0: Attached scsi
generic sg5 type 1
Sep 27 10:30:15 genepi1 kernel: scsi 5:0:1:1: Attached scsi
generic sg6 type 8
Sep 27 10:30:15 genepi1 kernel: osst :I: Tape driver with
OnStream
support version 0.99.4
Sep 27 10:30:15 genepi1 kernel: osst :I: $Id: osst.c,v 1.73
2005/01/01
21:13:34 wriede Exp $
Sep 27 10:30:15 genepi1 kernel: Driver 'osst' needs
updating - please
use bus_type methods
Sep 27 10:30:15 genepi1 kernel: st: Version 20080224, fixed
bufsize
32768, s/g segs 256
Sep 27 10:30:15 genepi1 kernel: Driver 'st' needs
updating - please
use bus_type methods
Sep 27 10:30:15 genepi1 kernel: st 5:0:1:0: Attached scsi
tape st0
Sep 27 10:30:15 genepi1 kernel: st 5:0:1:0: st0: try direct
i/o: yes
(alignment 4 B)
Sep 27 10:30:15 genepi1 kernel: eth0: Link is Up 1000 Mbps
Full
Duplex, Flow Control: RX
Sep 27 10:30:15 genepi1 kernel: ADDRCONF(NETDEV_CHANGE):
eth0: link
becomes ready
Sep 27 10:30:15 genepi1 kernel: ADDRCONF(NETDEV_UP): eth1:
link is not ready
Sep 27 10:54:58 genepi1 yum: Installed:
mtx-1.3.12-1.fc9.x86_64
Sep 27 10:58:19 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
(0x03:0x010D):
Invalid field in CDB:.
Sep 27 10:58:19 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
(0x03:0x0101):
Invalid command opcode:opcode=0xB8.
Sep 27 10:58:19 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
(0x03:0x0101):
Invalid command opcode:opcode=0xB8.
Sep 27 11:02:27 genepi1 kernel: st 5:0:1:0: Attempting to
queue an
ABORT message:CDB: 0x12 0x0 0x0 0x0 0x38 0x0
Sep 27 11:02:27 genepi1 kernel: scsi5: At time of recovery,
card was not paused
Sep 27 11:02:27 genepi1 kernel:
>>>>>>>>>>>>>>>>>>
Dump Card State
Begins
<<<<<<<<<<<<<<<<<
Sep 27 11:02:27 genepi1 kernel: scsi5: Dumping Card State
at program
address 0x34 Mode 0x22
Sep 27 11:02:27 genepi1 kernel: Card was paused
Sep 27 11:02:27 genepi1Sep 27 11:02:27 genepi1 kernel:
INTSTAT[0x0]
SELOID[0x1] SELID[0x10] HS_MAILBOX[0x0]
Sep 27 11:02:27 genepi1 kernel: INTCTL[0x80]
SEQINTSTAT[0x0]
SAVED_MODE[0x11] DFFSTAT[0x33]
Sep 27 11:02:27 genepi1 kernel: SCSISIGI[0x0]
SCSIPHASE[0x0]
SCSIBUS[0x0] LASTPHASE[0x1]
Sep 27 11:02:27 genepi1 kernel: SCSISEQ0[0x0]
SCSISEQ1[0x12]
SEQCTL0[0x0] SEQINTCTL[0x0]
Sep 27 11:02:27 genepi1 kernel: SEQ_FLAGS[0x0]
SEQ_FLAGS2[0x4]
QFREEZE_COUNT[0x7]
Sep 27 11:02:27 genepi1 kernel: KERNEL_QFREEZE_COUNT[0x6]
MK_MESSAGE_SCB[0xff00]
Sep 27 11:02:27 genepi1 kernel: MK_MESSAGE_SCSIID[0xff]
SSTAT0[0x0] SSTAT1[0x8]
Sep 27 11:02:27 genepi1 kernel: SSTAT2[0x0] SSTAT3[0x0]
PERRDIAG[0x0]
SIMODE1[0xa4]
Sep 27 11:02:27 genepi1 kernel: LQISTAT0[0x0] LQISTAT1[0x0]
LQISTAT2[0x0] LQOSTAT0[0x0]
Sep 27 11:02:27 genepi1 kernel: LQOSTAT1[0x0]
LQOSTAT2[0xe1]
Sep 27 11:02:27 genepi1 kernel:
Sep 27 11:02:27 genepi1 kernel: SCB Count = 4 CMDS_PENDING
= 0 LASTSCB
0xffff CURRSCB 0x3 NEXTSCB 0xff80
Sep 27 11:02:27 genepi1 kernel: qinstart = 44 qinfifonext =
46
Sep 27 11:02:27 genepi1 kernel: QINFIFO: 0x3 0x2
Sep 27 11:02:27 genepi1 kernel: WAITING_TID_QUEUES:
Sep 27 11:02:27 genepi1 kernel: Pending list:
Sep 27 11:02:27 genepi1 kernel: 2 FIFO_USE[0x0]
SCB_CONTROL[0x68]
SCB_SCSIID[0x17]
Sep 27 11:02:27 genepi1 kernel: 3 FIFO_USE[0x2]
SCB_CONTROL[0x68]
SCB_SCSIID[0x17]
Sep 27 11:02:27 genepi1 kernel: Total 2
Sep 27 11:02:27 genepi1 kernel: Kernel Free SCB list: 1 0
Sep 27 11:02:27 genepi1 kernel: Sequencer Complete
DMA-inprog list:
Sep 27 11:02:27 genepi1 kernel: Sequencer Complete list:
Sep 27 11:02:27 genepi1 kernel: Sequencer DMA-Up and
Complete list:
Sep 27 11:02:27 genepi1 kernel: Sequencer On QFreeze and
Complete list:
Sep 27 11:02:27 genepi1 kernel:
Sep 27 11:02:27 genepi1 kernel:
Sep 27 11:02:27 genepi1 kernel: scsi5: FIFO0 Free, LONGJMP
== 0x82a3, SCB 0x3
Sep 27 11:02:27 genepi1 kernel: SEQIMODE[0x3f]
SEQINTSRC[0x0]
DFCNTRL[0x0] DFSTATUS[0x89]
Sep 27 11:02:27 genepi1 kernel: SG_CACHE_SHADOW[0x2]
SG_STATE[0x0]
DFFSXFRCTL[0x0]
Sep 27 11:02:27 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
SHADDR =
0x00, SHCNT = 0x0
Sep 27 11:02:27 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
CCSGCTL[0x10]
Sep 27 11:02:27 genepi1 kernel:
Sep 27 11:02:27 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP
== 0x8063, SCB 0x3
Sep 27 11:02:27 genepi1 kernel: SEQIMODE[0x3f]
SEQINTSRC[0x0]
DFCNTRL[0x0] DFSTATUS[0x89]
Sep 27 11:02:27 genepi1 kernel: SG_CACHE_SHADOW[0x2]
SG_STATE[0x0]
DFFSXFRCTL[0x0]
Sep 27 11:02:27 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
SHADDR =
0x00, SHCNT = 0x0
Sep 27 11:02:27 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
CCSGCTL[0x10]
Sep 27 11:02:27 genepi1 kernel: LQIN: 0x8 0x0 0x0 0x3 0x0
0x1 0x0 0x0
0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
Sep 27 11:02:27 genepi1 kernel: scsi5: LQISTATE = 0x0,
LQOSTATE = 0x0,
OPTIONMODE = 0x52
Sep 27 11:02:27 genepi1 kernel: scsi5: OS_SPACE_CNT = 0x20
MAXCMDCNT = 0x1
Sep 27 11:02:27 genepi1 kernel: scsi5: SAVED_SCSIID = 0x0
SAVED_LUN = 0x0
Sep 27 11:02:27 genepi1 kernel: SIMODE0[0xc]
Sep 27 11:02:27 genepi1 kernel: CCSCBCTL[0x0]
Sep 27 11:02:27 genepi1 kernel: scsi5: REG0 == 0x3, SINDEX
= 0x104,
DINDEX = 0x104
Sep 27 11:02:27 genepi1 kernel: scsi5: SCBPTR == 0x3,
SCB_NEXT ==
0xff80, SCB_NEXT2 == 0xff80
Sep 27 11:02:27 genepi1 kernel: CDB 3 0 0 83 a 8c
Sep 27 11:02:27 genepi1 kernel: STACK: 0x20 0x0 0x0 0x0 0x0
0x0 0x0 0x0
Sep 27 11:02:27 genepi1 kernel:
<<<<<<<<<<<<<<<<<
Dump Card State Ends
>>>>>>>>>>>>>>>>>>
Sep 27 11:02:27 genepi1 kernel: scsi5:0:1:0: Cmd aborted
from QINFIFO
Sep 27 11:02:37 genepi1 kernel: st 5:0:1:0: Attempting to
queue an
ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
Sep 27 11:02:37 genepi1 kernel: scsi5: At time of recovery,
card was not paused
Sep 27 11:02:37 genepi1 kernel:
>>>>>>>>>>>>>>>>>>
Dump Card State
Begins
<<<<<<<<<<<<<<<<<
Sep 27 11:02:37 genepi1 kernel: scsi5: Dumping Card State
at program
address 0x18 Mode 0x33
kernel: INTSTAT[0x0] SELOID[0x1] SELID[0x10]
HS_MAILBOX[0x0]
Sep 27 11:02:27 genepi1 kernel: INTCTL[0x80]
SEQINTSTAT[0x0]
SAVED_MODE[0x11] DFFSTAT[0x33]
Sep 27 11:02:37 genepi1 kernel:
>>>>>>>>>>>>>>>>>>
Dump Card State
Begins
<<<<<<<<<<<<<<<<<
Sep 27 11:02:37 genepi1 kernel: scsi5: Dumping Card State
at program
address 0x18 Mode 0x33
Sep 27 11:02:37 genepi1 kernel: Card was paused
Sep 27 11:02:37 genepi1 kernel: INTSTAT[0x0] SELOID[0x1]
SELID[0x10]
HS_MAILBOX[0x0]
Sep 27 11:02:37 genepi1 kernel: INTCTL[0x80]
SEQINTSTAT[0x0]
SAVED_MODE[0x11] DFFSTAT[0x33]
Sep 27 11:02:37 genepi1 kernel: SCSISIGI[0x0]
SCSIPHASE[0x0]
SCSIBUS[0x0] LASTPHASE[0x1]
Sep 27 11:02:37 genepi1 kernel: SCSISEQ0[0x0]
SCSISEQ1[0x12]
SEQCTL0[0x0] SEQINTCTL[0x0]
Sep 27 11:02:37 genepi1 kernel: SEQ_FLAGS[0x0]
SEQ_FLAGS2[0x4]
QFREEZE_COUNT[0x7]
Sep 27 11:02:37 genepi1 kernel: KERNEL_QFREEZE_COUNT[0x6]
MK_MESSAGE_SCB[0xff00]
Sep 27 11:02:37 genepi1 kernel: MK_MESSAGE_SCSIID[0xff]
SSTAT0[0x0] SSTAT1[0x0]
Sep 27 11:02:37 genepi1 kernel: SSTAT2[0x0] SSTAT3[0x0]
PERRDIAG[0x0]
SIMODE1[0xa4]
Sep 27 11:02:37 genepi1 kernel: LQISTAT0[0x0] LQISTAT1[0x0]
LQISTAT2[0x0] LQOSTAT0[0x0]
Sep 27 11:02:37 genepi1 kernel: LQOSTAT1[0x0]
LQOSTAT2[0xe1]
Sep 27 11:02:37 genepi1 kernel:
Sep 27 11:02:37 genepi1 kernel: SCB Count = 4 CMDS_PENDING
= 0 LASTSCB
0xffff CURRSCB 0x3 NEXTSCB 0xff80
Sep 27 11:02:37 genepi1 kernel: qinstart = 44 qinfifonext =
46
Sep 27 11:02:37 genepi1 kernel: QINFIFO: 0x3 0x2
Sep 27 11:02:37 genepi1 kernel: WAITING_TID_QUEUES:
Sep 27 11:02:37 genepi1 kernel: Pending list:
Sep 27 11:02:37 genepi1 kernel: 2 FIFO_USE[0x0]
SCB_CONTROL[0x68]
SCB_SCSIID[0x17]
Sep 27 11:02:37 genepi1 kernel: 3 FIFO_USE[0x2]
SCB_CONTROL[0x68]
SCB_SCSIID[0x17]
Sep 27 11:02:37 genepi1 kernel: Total 2
Sep 27 11:02:37 genepi1 kernel: Kernel Free SCB list: 1 0
Sep 27 11:02:37 genepi1 kernel: Sequencer Complete
DMA-inprog list:
Sep 27 11:02:37 genepi1 kernel: Sequencer Complete list:
Sep 27 11:02:37 genepi1 kernel: Sequencer DMA-Up and
Complete list:
Sep 27 11:02:37 genepi1 kernel: Sequencer On QFreeze and
Complete list:
Sep 27 11:02:37 genepi1 kernel:
Sep 27 11:02:37 genepi1 kernel:
Sep 27 11:02:37 genepi1 kernel: scsi5: FIFO0 Free, LONGJMP
== 0x82a3, SCB 0x3
Sep 27 11:02:37 genepi1 kernel: SEQIMODE[0x3f]
SEQINTSRC[0x0]
DFCNTRL[0x0] DFSTATUS[0x89]
Sep 27 11:02:37 genepi1 kernel: SG_CACHE_SHADOW[0x2]
SG_STATE[0x0]
DFFSXFRCTL[0x0]
Sep 27 11:02:37 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
SHADDR =
0x00, SHCNT = 0x0
Sep 27 11:02:37 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
CCSGCTL[0x10]
Sep 27 11:02:37 genepi1 kernel:
Sep 27 11:02:37 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP
== 0x8063, SCB 0x3
Sep 27 11:02:37 genepi1 kernel: SEQIMODE[0x3f]
SEQINTSRC[0x0]
DFCNTRL[0x0] DFSTATUS[0x89]
Sep 27 11:02:37 genepi1 kernel: SG_CACHE_SHADOW[0x2]
SG_STATE[0x0]
DFFSXFRCTL[0x0]
Sep 27 11:02:37 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
SHADDR =
0x00, SHCNT = 0x0
Sep 27 11:02:37 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
CCSGCTL[0x10]
Sep 27 11:02:37 genepi1 kernel: LQIN: 0x8 0x0 0x0 0x3 0x0
0x1 0x0 0x0
0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
Sep 27 11:02:37 genepi1 kernel: scsi5: LQISTATE = 0x0,
LQOSTATE = 0x0,
OPTIONMODE = 0x52
Sep 27 11:02:37 genepi1 kernel: scsi5: OS_SPACE_CNT = 0x20
MAXCMDCNT = 0x1
Sep 27 11:02:37 genepi1 kernel: scsi5: SAVED_SCSIID = 0x0
SAVED_LUN = 0x0
Sep 27 11:02:37 genepi1 kernel: SIMODE0[0xc]
Sep 27 11:02:37 genepi1 kernel: CCSCBCTL[0x0]
Sep 27 11:02:37 genepi1 kernel: scsi5: REG0 == 0xffff,
SINDEX = 0x104,
DINDEX = 0x104
Sep 27 11:02:37 genepi1 kernel: scsi5: SCBPTR == 0x3,
SCB_NEXT ==
0xff80, SCB_NEXT2 == 0xff80
Sep 27 11:02:37 genepi1 kernel: CDB 3 0 0 83 a 8c
Sep 27 11:02:37 genepi1 kernel: STACK: 0x0 0x0 0x0 0x0 0x0
0x0 0x0 0x0
Sep 27 11:02:37 Sep 27 11:02:37 genepi1 kernel:
scsi5:0:1:0: Cmd
aborted from QINFIFO
Sep 27 11:02:37 genepi1 kernel: scsi 5:0:1:1: Attempting to
queue an
ABORT message:CDB: 0x1a 0x8 0x1d 0x0 0x88 0x0
Sep 27 11:02:37 genepi1 kernel: scsi5: At time of recovery,
card was not paused
Sep 27 11:02:37 genepi1 kernel:
>>>>>>>>>>>>>>>>>>
Dump Card State
Begins
<<<<<<<<<<<<<<<<<
Sep 27 11:02:37 genepi1 kernel: scsi5: Dumping Card State
at program
address 0x31 Mode 0x11
Sep 27 11:02:37 genepi1 kernel: Card was paused
Sep 27 11:02:37 genepi1 kernel: INTSTAT[0x0] SELOID[0x1]
SELID[0x10]
HS_MAILBOX[0x0]
Sep 27 11:02:37 genepi1 kernel: INTCTL[0x80]
SEQINTSTAT[0x0]
SAVED_MODE[0x11] DFFSTAT[0x33]
Sep 27 11:02:37 genepi1 kernel: SCSISIGI[0x0]
SCSIPHASE[0x0]
SCSIBUS[0x0] LASTPHASE[0x1]
Sep 27 11:02:37 genepi1 kernel: SCSISEQ0[0x0]
SCSISEQ1[0x12]
SEQCTL0[0x0] SEQINTCTL[0x0]
Sep 27 11:02:37 genepi1 kernel: SEQ_FLAGS[0x0]
SEQ_FLAGS2[0x4]
QFREEZE_COUNT[0x7]
Sep 27 11:02:37 genepi1 kernel: KERNEL_QFREEZE_COUNT[0x6]
MK_MESSAGE_SCB[0xff00]
Sep 27 11:02:37 genepi1 kernel: MK_MESSAGE_SCSIID[0xff]
SSTAT0[0x0] SSTAT1[0x0]
Sep 27 11:02:37 genepi1 kernel: SSTAT2[0x0] SSTAT3[0x0]
PERRDIAG[0x0]
SIMODE1[0xa4]
Sep 27 11:02:37 genepi1 kernel: LQISTAT0[0x0] LQISTAT1[0x0]
LQISTAT2[0x0] LQOSTAT0[0x0]
Sep 27 11:02:37 genepi1 kernel: LQOSTAT1[0x0]
LQOSTAT2[0xe1]
Sep 27 11:02:37 genepi1 kernel:
Sep 27 11:02:37 genepi1 kernel: SCB Count = 4 CMDS_PENDING
= 0 LASTSCB
0xffff CURRSCB 0x3 NEXTSCB 0xff80
Sep 27 11:02:37 genepi1 kernel: qinstart = 44 qinfifonext =
45
Sep 27 11:02:37 genepi1 kernel: QINFIFO: 0x3
Sep 27 11:02:37 genepi1 kernel: WAITING_TID_QUEUES:
Sep 27 11:02:37 genepi1 kernel: Pending list:
Sep 27 11:02:37 genepi1 kernel: 3 FIFO_USE[0x0]
SCB_CONTROL[0x68]
SCB_SCSIID[0x17]
Sep 27 11:02:37 genepi1 kernel: Total 1
Sep 27 11:02:37 genepi1 kernel: Kernel Free SCB list: 2 1 0
Sep 27 11:02:37 genepi1 kernel: Sequencer Complete
DMA-inprog list:
Sep 27 11:02:37 genepi1 kernel: Sequencer Complete list:
Sep 27 11:02:37 genepi1 kernel: Sequencer DMA-Up and
Complete list:
Sep 27 11:02:37 genepi1 kernel: Sequencer On QFreeze and
Complete list:
Sep 27 11:02:37 genepi1 kernel:
Sep 27 11:02:37 genepi1 kernel:
Sep 27 11:02:37 genepi1 kernel: scsi5: FIFO0 Free, LONGJMP
== 0x82a3, SCB 0x3
Sep 27 11:02:37 genepi1 kernel: SEQIMODE[0x3f]
SEQINTSRC[0x0]
DFCNTRL[0x0] DFSTATUS[0x89]
Sep 27 11:02:37 genepi1 kernel: SG_CACHE_SHADOW[0x2]
SG_STATE[0x0]
DFFSXFRCTL[0x0]
Sep 27 11:02:37 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
SHADDR =
0x00, SHCNT = 0x0
Sep 27 11:02:37 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
CCSGCTL[0x10]
Sep 27 11:02:37 genepi1 kernel:
Sep 27 11:02:37 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP
== 0x8063, SCB 0x3
Sep 27 11:02:37 genepi1 kernel: SEQIMODE[0x3f]
SEQINTSRC[0x0]
DFCNTRL[0x0] DFSTATUS[0x89]
Sep 27 11:02:37 genepi1 kernel: SG_CACHE_SHADOW[0x2]
SG_STATE[0x0]
DFFSXFRCTL[0x0]
Sep 27 11:02:37 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
SHADDR =
0x00, SHCNT = 0x0
Sep 27 11:02:37 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
CCSGCTL[0x10]
Sep 27 11:02:37 genepi1 kernel: LQIN: 0x8 0x0 0x0 0x3 0x0
0x1 0x0 0x0
0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
Sep 27 11:02:37 genepi1 kernel: scsi5: LQISTATE = 0x0,
LQOSTATE = 0x0,
OPTIONMODE = 0x52
Sep 27 11:02:37 genepi1 kernel: scsi5: OS_SPACE_CNT = 0x20
MAXCMDCNT = 0x1
Sep 27 11:02:37 genepi1 kernel: scsi5: SAVED_SCSIID = 0x0
SAVED_LUN = 0x0
Sep 27 11:02:37 genepi1 kernel: SIMODE0[0xc]
Sep 27 11:02:37 genepi1 kernel: CCSCBCTL[0x0]
Sep 27 11:02:37 genepi1 kernel: scsi5: REG0 == 0x3, SINDEX
= 0x104,
DINDEX = 0x104
Sep 27 11:02:37 genepi1 kernel: scsi5: SCBPTR == 0x3,
SCB_NEXT ==
0xff80, SCB_NEXT2 == 0xff80
Sep 27 11:02:37 genepi1 kernel: CDB 3 0 0 83 a 8c
Sep 27 11:02:37 genepi1 kernel: STACK: 0x1f 0x0 0x0 0x0 0x0
0x0 0x0 0x0
Sep 27 11:02:37 genepi1 kernel:
<<<<<<<<<<<<<<<<<
Dump Card State Ends
>>>>>>>>>>>>>>>>>>
genepi1 kernel:
<<<<<<<<<<<<<<<<<
Dump Card State Ends
>>>>>>>>>>>>>>>>>>
Sep 27 11:02:37 genepi1 kernel: scsi5:0:1:0: Cmd aborted
from QINFIFO
Sep 27 11:02:37 genepi1 kernel: scsi 5:0:1:1: Attempting to
queue an
ABORT message:CDB: 0x1a 0x8 0x1d 0x0 0x88 0x0
Sep 27 11:02:37 genepi1 kernel: scsi5:0:1:0: Cmd aborted
from QINFIFO
Sep 27 11:02:37 genepi1 kernel: scsi 5:0:1:1: Attempting to
queue an
ABORT message:CDB: 0x1a 0x8 0x1d 0x0 0x88 0x0
Sep 27 11:02:37 genepi1 kernel: scsi5: At time of recovery,
card was not paused
Sep 27 11:02:37 genepi1 kernel:
>>>>>>>>>>>>>>>>>>
Dump Card State
Begins
<<<<<<<<<<<<<<<<<
Sep 27 11:02:37 genepi1 kernel: scsi5: Dumping Card State
at program
address 0x31 Mode 0x11
Sep 27 11:02:37 genepi1 kernel: Card was paused
Sep 27 11:02:37 genepi1 kernel: INTSTAT[0x0] SELOID[0x1]
SELID[0x10]
HS_MAILBOX[0x0]
Sep 27 11:02:37 genepi1 kernel: INTCTL[0x80]
SEQINTSTAT[0x0]
SAVED_MODE[0x11] DFFSTAT[0x33]
Sep 27 11:02:37 genepi1 kernel: SCSISIGI[0x0]
SCSIPHASE[0x0]
SCSIBUS[0x0] LASTPHASE[0x1]
Sep 27 11:02:37 genepi1 kernel: SCSISEQ0[0x0]
SCSISEQ1[0x12]
SEQCTL0[0x0] SEQINTCTL[0x0]
Sep 27 11:02:37 genepi1 kernel: SEQ_FLAGS[0x0]
SEQ_FLAGS2[0x4]
QFREEZE_COUNT[0x7]
Sep 27 11:02:37 genepi1 kernel: KERNEL_QFREEZE_COUNT[0x6]
MK_MESSAGE_SCB[0xff00]
Sep 27 11:02:37 genepi1 kernel: MK_MESSAGE_SCSIID[0xff]
SSTAT0[0x0] SSTAT1[0x0]
Sep 27 11:02:37 genepi1 kernel: SSTAT2[0x0] SSTAT3[0x0]
PERRDIAG[0x0]
SIMODE1[0xa4]
Sep 27 11:02:37 genepi1 kernel: LQISTAT0[0x0] LQISTAT1[0x0]
LQISTAT2[0x0] LQOSTAT0[0x0]
Sep 27 11:02:37 genepi1 kernel: LQOSTAT1[0x0]
LQOSTAT2[0xe1]
Sep 27 11:02:37 genepi1 kernel:
Sep 27 11:02:37 genepi1 kernel: SCB Count = 4 CMDS_PENDING
= 0 LASTSCB
0xffff CURRSCB 0x3 NEXTSCB 0xff80
Sep 27 11:02:37 genepi1 kernel: qinstart = 44 qinfifonext =
45
Sep 27 11:02:37 genepi1 kernel: QINFIFO: 0x3
Sep 27 11:02:37 genepi1 kernel: WAITING_TID_QUEUES:
Sep 27 11:02:37 genepi1 kernel: Pending list:
Sep 27 11:02:37 genepi1 kernel: 3 FIFO_USE[0x0]
SCB_CONTROL[0x68]
SCB_SCSIID[0x17]
Sep 27 11:02:37 genepi1 kernel: Total 1
Sep 27 11:02:37 genepi1 kernel: Kernel Free SCB list: 2 1 0
Sep 27 11:02:37 genepi1 kernel: Sequencer Complete
DMA-inprog list:
Sep 27 11:02:37 genepi1 kernel: Sequencer Complete list:
Sep 27 11:02:37 genepi1 kernel: Sequencer DMA-Up and
Complete list:
Sep 27 11:02:37 genepi1 kernel: Sequencer On QFreeze and
Complete list:
Sep 27 11:02:37 genepi1 kernel:
Sep 27 11:02:37 genepi1 kernel:
Sep 27 11:02:37 genepi1 kernel: scsi5: FIFO0 Free, LONGJMP
== 0x82a3, SCB 0x3
Sep 27 11:02:37 genepi1 kernel: SEQIMODE[0x3f]
SEQINTSRC[0x0]
DFCNTRL[0x0] DFSTATUS[0x89]
Sep 27 11:02:37 genepi1 kernel: SG_CACHE_SHADOW[0x2]
SG_STATE[0x0]
DFFSXFRCTL[0x0]
Sep 27 11:02:37 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
SHADDR =
0x00, SHCNT = 0x0
Sep 27 11:02:37 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
CCSGCTL[0x10]
Sep 27 11:02:37 genepi1 kernel:
Sep 27 11:02:37 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP
== 0x8063, SCB 0x3
Sep 27 11:02:37 genepi1 kernel: SEQIMODE[0x3f]
SEQINTSRC[0x0]
DFCNTRL[0x0] DFSTATUS[0x89]
Sep 27 11:02:37 genepi1 kernel: SG_CACHE_SHADOW[0x2]
SG_STATE[0x0]
DFFSXFRCTL[0x0]
Sep 27 11:02:37 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
SHADDR =
0x00, SHCNT = 0x0
Sep 27 11:02:37 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
CCSGCTL[0x10]
Sep 27 11:02:37 genepi1 kernel: LQIN: 0x8 0x0 0x0 0x3 0x0
0x1 0x0 0x0
0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
Sep 27 11:02:37 genepi1 kernel: scsi5: LQISTATE = 0x0,
LQOSTATE = 0x0,
OPTIONMODE = 0x52
Sep 27 11:02:37 genepi1 kernel: scsi5: OS_SPACE_CNT = 0x20
MAXCMDCNT = 0x1
Sep 27 11:02:37 genepi1 kernel: scsi5: SAVED_SCSIID = 0x0
SAVED_LUN = 0x0
Sep 27 11:02:37 genepi1 kernel: SIMODE0[0xc]
Sep 27 11:02:37 genepi1 kernel: CCSCBCTL[0x0]
Sep 27 11:02:37 genepi1 kernel: scsi5: REG0 == 0x3, SINDEX
= 0x104,
DINDEX = 0x104
Sep 27 11:02:37 genepi1 kernel: scsi5: SCBPTR == 0x3,
SCB_NEXT ==
0xff80, SCB_NEXT2 == 0xff80
Sep 27 11:02:37 genepi1 kernel: CDB 3 0 0 83 a 8c
Sep 27 11:02:37 genepi1 kernel: STACK: 0x1f 0x0 0x0 0x0 0x0
0x0 0x0 0x0
Sep 27 11:02:37 genepi1 kernel:
<<<<<<<<<<<<<<<<<
Dump Card State Ends
>>>>>>>>>>>>>>>>>>
Sep 27 11:02:37 genepi1 kernel: STACK: 0x1f 0x0 0x0 0x0 0x0
0x0 0x0 0x0
Sep 27 11:02:37 genepi1 kernel:
<<<<<<<<<<<<<<<<<
Dump Card State Ends
>>>>>>>>>>>>>>>>>>
Sep 27 11:02:37 genepi1 kernel: scsi5:0:1:1: Cmd aborted
from QINFIFO
Sep 27 11:02:47 genepi1 kernel: scsi 5:0:1:1: Attempting to
queue an
ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
Sep 27 11:02:47 genepi1 kernel: scsi5: At time of recovery,
card was not paused
Sep 27 11:02:47 genepi1 kernel:
>>>>>>>>>>>>>>>>>>
Dump Card State
Begins
<<<<<<<<<<<<<<<<<
Sep 27 11:02:47 genepi1 kernel: scsi5: Dumping Card State
at program
address 0x18 Mode 0x33
Sep 27 11:02:47 genepi1 kernel: Card was paused
Sep 27 11:02:47 genepi1 kernel: INTSTAT[0x0] SELOID[0x1]
SELID[0x10]
HS_MAILBOX[0x0]
Sep 27 11:02:47 genepi1 kernel: INTCTL[0x80]
SEQINTSTAT[0x0]
SAVED_MODE[0x11] DFFSTAT[0x33]
Sep 27 11:02:47 genepi1 kernel: SCSISIGI[0x0]
SCSIPHASE[0x0]
SCSIBUS[0x0] LASTPHASE[0x1]
Sep 27 11:02:47 genepi1 kernel: SCSISEQ0[0x0]
SCSISEQ1[0x12]
SEQCTL0[0x0] SEQINTCTL[0x0]
Sep 27 11:02:47 genepi1 kernel: SEQ_FLAGS[0x0]
SEQ_FLAGS2[0x4]
QFREEZE_COUNT[0x7]
Sep 27 11:02:47 genepi1 kernel: KERNEL_QFREEZE_COUNT[0x6]
MK_MESSAGE_SCB[0xff00]
Sep 27 11:02:47 genepi1 kernel: MK_MESSAGE_SCSIID[0xff]
SSTAT0[0x0] SSTAT1[0x0]
Sep 27 11:02:47 genepi1 kernel: SSTAT2[0x0] SSTAT3[0x0]
PERRDIAG[0x0]
SIMODE1[0xa4]
Sep 27 11:02:47 genepi1 kernel: LQISTAT0[0x0] LQISTAT1[0x0]
LQISTAT2[0x0] LQOSTAT0[0x0]
Sep 27 11:02:47 genepi1 kernel: LQOSTAT1[0x0]
LQOSTAT2[0xe1]
Sep 27 11:02:47 genepi1 kernel:
Sep 27 11:02:47 genepi1 kernel: SCB Count = 4 CMDS_PENDING
= 0 LASTSCB
0xffff CURRSCB 0x3 NEXTSCB 0xff80
Sep 27 11:02:47 genepi1 kernel: qinstart = 44 qinfifonext =
45
Sep 27 11:02:47 genepi1 kernel: QINFIFO: 0x3
Sep 27 11:02:47 genepi1 kernel: WAITING_TID_QUEUES:
Sep 27 11:02:47 genepi1 kernel: Pending list:
Sep 27 11:02:47 genepi1 kernel: 3 FIFO_USE[0x0]
SCB_CONTROL[0x68]
SCB_SCSIID[0x17]
Sep 27 11:02:47 genepi1 kernel: Total 1
Sep 27 11:02:47 genepi1 kernel: Kernel Free SCB list: 2 1 0
Sep 27 11:02:47 genepi1 kernel: Sequencer Complete
DMA-inprog list:
Sep 27 11:02:47 genepi1 kernel: Sequencer Complete list:
Sep 27 11:02:47 genepi1 kernel: Sequencer DMA-Up and
Complete list:
Sep 27 11:02:47 genepi1 kernel: Sequencer On QFreeze and
Complete list:
Sep 27 11:02:47 genepi1 kernel:
Sep 27 11:02:47 genepi1 kernel:
Sep 27 11:02:47 genepi1 kernel: scsi5: FIFO0 Free, LONGJMP
== 0x82a3, SCB 0x3
Sep 27 11:02:47 genepi1 kernel: SEQIMODE[0x3f]
SEQINTSRC[0x0]
DFCNTRL[0x0] DFSTATUS[0x89]
Sep 27 11:02:47 genepi1 kernel: SG_CACHE_SHADOW[0x2]
SG_STATE[0x0]
DFFSXFRCTL[0x0]
Sep 27 11:02:47 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
SHADDR =
0x00, SHCNT = 0x0
Sep 27 11:02:47 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
CCSGCTL[0x10]
Sep 27 11:02:47 genepi1 kernel:
Sep 27 11:02:47 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP
== 0x8063, SCB 0x3
Sep 27 11:02:47 genepi1 kernel: SEQIMODE[0x3f]
SEQINTSRC[0x0]
DFCNTRL[0x0] DFSTATUS[0x89]
Sep 27 11:02:47 genepi1 kernel: SG_CACHE_SHADOW[0x2]
SG_STATE[0x0]
DFFSXFRCTL[0x0]
Sep 27 11:02:47 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
SHADDR =
0x00, SHCNT = 0x0
Sep 27 11:02:47 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
CCSGCTL[0x10]
Sep 27 11:02:47 genepi1 kernel: LQIN: 0x8 0x0 0x0 0x3 0x0
0x1 0x0 0x0
0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
Sep 27 11:02:47 genepi1 kernel: scsi5: LQISTATE = 0x0,
LQOSTATE = 0x0,
OPTIONMODE = 0x52
Sep 27 11:02:47 genepi1 kernel: scsi5: OS_SPACE_CNT = 0x20
MAXCMDCNT = 0x1
Sep 27 11:02:47 genepi1 kernel: scsi5: SAVED_SCSIID = 0x0
SAVED_LUN = 0x0
Sep 27 11:02:47 genepi1 kernel: SIMODE0[0xc]
Sep 27 11:02:47 genepi1 kernel: CCSCBCTL[0x0]
Sep 27 11:02:47 genepi1 kernel: scsi5: REG0 == 0xffff,
SINDEX = 0x104,
DINDEX = 0x104
Sep 27 11:02:47 genepi1 kernel: scsi5: SCBPTR == 0x3,
SCB_NEXT ==
0xff80, SCB_NEXT2 == 0xff80
Sep 27 11:02:47 genepi1 kernel: CDB 3 0 0 83 a 8c
Sep 27 11:02:47 genepi1 kernel: scsi5: SCBPTR == 0x3,
SCB_NEXT ==
0xff80, SCB_NEXT2 == 0xff80
Sep 27 11:02:47 genepi1 kernel: CDB 3 0 0 83 a 8c
Sep 27 11:02:47 genepi1 kernel: STACK: 0x0 0x0 0x0 0x0 0x0
0x0 0x0 0x0
Sep 27 11:02:47 genepi1 kernel:
<<<<<<<<<<<<<<<<<
Dump Card State Ends
>>>>>>>>>>>>>>>>>>
Sep 27 11:02:47 genepi1 kernel: scsi5:0:1:1: Cmd aborted
from QINFIFO
Sep 27 11:02:47 genepi1 kernel: st 5:0:1:0: Attempting to
queue a
TARGET RESET message:CDB: 0x12 0x0 0x0 0x0 0x38 0x0
Sep 27 11:02:47 genepi1 kernel: scsi5: Device reset code
sleeping
Sep 27 11:02:52 genepi1 kernel: scsi5: Device reset timer
expired (active 1)
Sep 27 11:02:52 genepi1 kernel: scsi5: Device reset
returning 0x2003
Sep 27 11:02:52 genepi1 kernel: scsi 5:0:1:1: Attempting to
queue a
TARGET RESET message:CDB: 0x1a 0x8 0x1d 0x0 0x88 0x0
Sep 27 11:02:52 genepi1 kernel: scsi5: Device reset code
sleeping
Sep 27 11:02:57 genepi1 kernel: scsi5: Device reset timer
expired (active 1)
Sep 27 11:02:57 genepi1 kernel: scsi5: Device reset
returning 0x2003
Sep 27 11:02:57 genepi1 kernel: Recovery SCB completes
Sep 27 11:02:57 genepi1 kernel: Recovery SCB completes
Sep 27 11:03:17 genepi1 kernel: st 5:0:1:0: Attempting to
queue an
ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
Sep 27 11:03:17 genepi1 kernel: scsi5: At time of recovery,
card was not paused
Sep 27 11:03:17 genepi1 kernel:
>>>>>>>>>>>>>>>>>>
Dump Card State
Begins
<<<<<<<<<<<<<<<<<
Sep 27 11:03:17 genepi1 kernel: scsi5: Dumping Card State
at program
address 0x9 Mode 0x33
Sep 27 11:03:17 genepi1 kernel: Card was paused
Sep 27 11:03:17 genepi1 kernel: INTSTAT[0x0] SELOID[0x1]
SELID[0x10]
HS_MAILBOX[0x0]
Sep 27 11:03:17 genepi1 kernel: INTCTL[0x80]
SEQINTSTAT[0x0]
SAVED_MODE[0x11] DFFSTAT[0x33]
Sep 27 11:03:17 genepi1 kernel: SCSISIGI[0x0]
SCSIPHASE[0x0]
SCSIBUS[0x0] LASTPHASE[0x1]
Sep 27 11:03:17 genepi1 kernel: SCSISEQ0[0x0]
SCSISEQ1[0x12]
SEQCTL0[0x0] SEQINTCTL[0x0]
Sep 27 11:03:17 genepi1 kernel: SEQ_FLAGS[0x0]
SEQ_FLAGS2[0x4]
QFREEZE_COUNT[0x7]
Sep 27 11:03:17 genepi1 kernel: KERNEL_QFREEZE_COUNT[0x6]
MK_MESSAGE_SCB[0xff00]
Sep 27 11:03:17 genepi1 kernel: MK_MESSAGE_SCSIID[0xff]
SSTAT0[0x0] SSTAT1[0x0]
Sep 27 11:03:17 genepi1 kernel: SSTAT2[0x0] SSTAT3[0x0]
PERRDIAG[0x0]
SIMODE1[0xa4]
Sep 27 11:03:17 genepi1 kernel: LQISTAT0[0x0] LQISTAT1[0x0]
LQISTAT2[0x0] LQOSTAT0[0x0]
Sep 27 11:03:17 genepi1 kernel: LQOSTAT1[0x0]
LQOSTAT2[0xe1]
Sep 27 11:03:17 genepi1 kernel:
Sep 27 11:03:17 genepi1 kernel: SCB Count = 4 CMDS_PENDING
= 0 LASTSCB
0xffff CURRSCB 0x3 NEXTSCB 0xff80
Sep 27 11:03:17 genepi1 kernel: qinstart = 44 qinfifonext =
45
Sep 27 11:03:17 genepi1 kernel: QINFIFO: 0x2
Sep 27 11:03:17 genepi1 kernel: WAITING_TID_QUEUES:
Sep 27 11:03:17 genepi1 kernel: Pending list:
Sep 27 11:03:17 genepi1 kernel: 2 FIFO_USE[0x0]
SCB_CONTROL[0x68]
SCB_SCSIID[0x17]
Sep 27 11:03:17 genepi1 kernel: Total 1
Sep 27 11:03:17 genepi1 kernel: Kernel Free SCB list: 3 1 0
Sep 27 11:03:17 genepi1 kernel: Sequencer Complete
DMA-inprog list:
Sep 27 11:03:17 genepi1 kernel: Sequencer Complete list:
Sep 27 11:03:17 genepi1 kernel: Sequencer DMA-Up and
Complete list:
Sep 27 11:03:17 genepi1 kernel: Sequencer On QFreeze and
Complete list:
Sep 27 11:03:17 genepi1 kernel:
Sep 27 11:03:17 genepi1 kernel:
Sep 27 11:03:17 genepi1 kernel: scsi5: FIFO0 Free, LONGJMP
== 0x80a3, SCB 0x3
Sep 27 11:03:17 genepi1 kernel: SEQIMODE[0x3f]
SEQINTSRC[0x0]
DFCNTRL[0x0] DFSTATUS[0x89]
Sep 27 11:03:17 genepi1 kernel: SG_CACHE_SHADOW[0x2]
SG_STATE[0x0]
DFFSXFRCTL[0x0]
Sep 27 11:03:17 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
SHADDR =
0x00, SHCNT = 0x0
Sep 27 11:03:17 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
CCSGCTL[0x10]
Sep 27 11:03:17 genepi1 kernel:
Sep 27 11:03:17 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP
== 0x8063, SCB 0x3
Sep 27 11:03:17 genepi1 kernel: SEQIMODE[0x3f]
SEQINTSRC[0x0]
DFCNTRL[0x0] DFSTATUS[0x89]
Sep 27 11:03:17 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP
== 0x8063, SCB 0x3
Sep 27 11:03:17 genepi1 kernel: SEQIMODE[0x3f]
SEQINTSRC[0x0]
DFCNTRL[0x0] DFSTATUS[0x89]
Sep 27 11:03:17 genepi1 kernel: SG_CACHE_SHADOW[0x2]
SG_STATE[0x0]
DFFSXFRCTL[0x0]
Sep 27 11:03:17 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
SHADDR =
0x00, SHCNT = 0x0
Sep 27 11:03:17 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
CCSGCTL[0x10]
Sep 27 11:03:17 genepi1 kernel: LQIN: 0x8 0x0 0x0 0x3 0x0
0x1 0x0 0x0
0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
Sep 27 11:03:17 genepi1 kernel: scsi5: LQISTATE = 0x0,
LQOSTATE = 0x0,
OPTIONMODE = 0x52
Sep 27 11:03:17 genepi1 kernel: scsi5: OS_SPACE_CNT = 0x20
MAXCMDCNT = 0x1
Sep 27 11:03:17 genepi1 kernel: scsi5: SAVED_SCSIID = 0x0
SAVED_LUN = 0x0
Sep 27 11:03:17 genepi1 kernel: SIMODE0[0xc]
Sep 27 11:03:17 genepi1 kernel: CCSCBCTL[0x0]
Sep 27 11:03:17 genepi1 kernel: scsi5: REG0 == 0xffff,
SINDEX = 0x104,
DINDEX = 0x104
Sep 27 11:03:17 genepi1 kernel: scsi5: SCBPTR == 0x3,
SCB_NEXT ==
0xff80, SCB_NEXT2 == 0xff80
Sep 27 11:03:17 genepi1 kernel: CDB 3 0 0 83 a 8c
Sep 27 11:03:17 genepi1 kernel: STACK: 0x0 0x0 0x0 0x0 0x0
0x0 0x0 0x0
Sep 27 11:03:17 genepi1 kernel:
<<<<<<<<<<<<<<<<<
Dump Card State Ends
>>>>>>>>>>>>>>>>>>
Sep 27 11:03:17 genepi1 kernel: scsi5:0:1:0: Cmd aborted
from QINFIFO
Sep 27 11:03:27 genepi1 kernel: scsi 5:0:1:1: Attempting to
queue an
ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
Sep 27 11:03:27 genepi1 kernel: scsi5: At time of recovery,
card was not paused
Sep 27 11:03:27 genepi1 kernel:
>>>>>>>>>>>>>>>>>>
Dump Card State
Begins
<<<<<<<<<<<<<<<<<
Sep 27 11:03:27 genepi1 kernel: scsi5: Dumping Card State
at program
address 0x22 Mode 0x33
Sep 27 11:03:27 genepi1 kernel: Card was paused
Sep 27 11:03:27 genepi1 kernel: INTSTAT[0x0] SELOID[0x1]
SELID[0x10]
HS_MAILBOX[0x0]
Sep 27 11:03:27 genepi1 kernel: INTCTL[0x80]
SEQINTSTAT[0x0]
SAVED_MODE[0x11] DFFSTAT[0x33]
Sep 27 11:03:27 genepi1 kernel: SCSISIGI[0x0]
SCSIPHASE[0x0]
SCSIBUS[0x0] LASTPHASE[0x1]
Sep 27 11:03:27 genepi1 kernel: SCSISEQ0[0x0]
SCSISEQ1[0x12]
SEQCTL0[0x0] SEQINTCTL[0x0]
Sep 27 11:03:27 genepi1 kernel: SEQ_FLAGS[0x0]
SEQ_FLAGS2[0x4]
QFREEZE_COUNT[0x7]
Sep 27 11:03:27 genepi1 kernel: KERNEL_QFREEZE_COUNT[0x6]
MK_MESSAGE_SCB[0xff00]
Sep 27 11:03:27 genepi1 kernel: MK_MESSAGE_SCSIID[0xff]
SSTAT0[0x0] SSTAT1[0x0]
Sep 27 11:03:27 genepi1 kernel: SSTAT2[0x0] SSTAT3[0x0]
PERRDIAG[0x0]
SIMODE1[0xa4]
Sep 27 11:03:27 genepi1 kernel: LQISTAT0[0x0] LQISTAT1[0x0]
LQISTAT2[0x0] LQOSTAT0[0x0]
Sep 27 11:03:27 genepi1 kernel: LQOSTAT1[0x0]
LQOSTAT2[0xe1]
Sep 27 11:03:27 genepi1 kernel:
Sep 27 11:03:27 genepi1 kernel: SCB Count = 4 CMDS_PENDING
= 0 LASTSCB
0xffff CURRSCB 0x3 NEXTSCB 0xff80
Sep 27 11:03:27 genepi1 kernel: qinstart = 44 qinfifonext =
45
Sep 27 11:03:27 genepi1 kernel: QINFIFO: 0x2
Sep 27 11:03:27 genepi1 kernel: WAITING_TID_QUEUES:
Sep 27 11:03:27 genepi1 kernel: Pending list:
Sep 27 11:03:27 genepi1 kernel: 2 FIFO_USE[0x0]
SCB_CONTROL[0x68]
SCB_SCSIID[0x17]
Sep 27 11:03:27 genepi1 kernel: Total 1
Sep 27 11:03:27 genepi1 kernel: Kernel Free SCB list: 3 1 0
Sep 27 11:03:27 genepi1 kernel: Sequencer Complete
DMA-inprog list:
Sep 27 11:03:27 genepi1 kernel: Sequencer Complete list:
Sep 27 11:03:27 genepi1 kernel: Sequencer DMA-Up and
Complete list:
Sep 27 11:03:27 genepi1 kernel: Sequencer On QFreeze and
Complete list:
Sep 27 11:03:27 genepi1 kernel:
Sep 27 11:03:27 genepi1 kernel:
Sep 27 11:03:27 genepi1 kernel: scsi5: FIFO0 Free, LONGJMP
== 0x80a3, SCB 0x3
Sep 27 11:03:27 genepi1 kernel: SEQIMODE[0x3f]
SEQINTSRC[0x0]
DFCNTRL[0x0] DFSTATUS[0x89]
Sep 27 11:03:27 genepi1 kernel: SG_CACHE_SHADOW[0x2]
SG_STATE[0x0]
DFFSXFRCTL[0x0]
Sep 27 11:03:Sep 27 11:03:27 genepi1 kernel: HADDR = 0x00,
HCNT = 0x0
CCSGCTL[0x10]
Sep 27 11:03:27 genepi1 kernel:
Sep 27 11:03:27 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP
== 0x8063, SCB 0x3
Sep 27 11:03:27 genepi1 kernel: SEQIMODE[0x3f]
SEQINTSRC[0x0]
DFCNTRL[0x0] DFSTATUS[0x89]
Sep 27 11:03:27 genepi1 kernel: SG_CACHE_SHADOW[0x2]
SG_STATE[0x0]
DFFSXFRCTL[0x0]
Sep 27 11:03:27 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
SHADDR =
0x00, SHCNT = 0x0
Sep 27 11:03:27 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
CCSGCTL[0x10]
Sep 27 11:03:27 genepi1 kernel: LQIN: 0x8 0x0 0x0 0x3 0x0
0x1 0x0 0x0
0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
Sep 27 11:03:27 genepi1 kernel: scsi5: LQISTATE = 0x0,
LQOSTATE = 0x0,
OPTIONMODE = 0x52
Sep 27 11:03:27 genepi1 kernel: scsi5: OS_SPACE_CNT = 0x20
MAXCMDCNT = 0x1
Sep 27 11:03:27 genepi1 kernel: scsi5: SAVED_SCSIID = 0x0
SAVED_LUN = 0x0
Sep 27 11:03:27 genepi1 kernel: SIMODE0[0xc]
Sep 27 11:03:27 genepi1 kernel: CCSCBCTL[0x0]
Sep 27 11:03:27 genepi1 kernel: scsi5: REG0 == 0xffff,
SINDEX = 0x104,
DINDEX = 0x104
Sep 27 11:03:27 genepi1 kernel: scsi5: SCBPTR == 0x3,
SCB_NEXT ==
0xff80, SCB_NEXT2 == 0xff80
Sep 27 11:03:27 genepi1 kernel: CDB 3 0 0 83 a 8c
Sep 27 11:03:27 genepi1 kernel: STACK: 0x1e 0x0 0x0 0x0 0x0
0x0 0x0 0x0
Sep 27 11:03:27 genepi1 kernel:
<<<<<<<<<<<<<<<<<
Dump Card State Ends
>>>>>>>>>>>>>>>>>>
Sep 27 11:03:27 genepi1 kernel: scsi5:0:1:1: Cmd aborted
from QINFIFO
Sep 27 11:03:27 genepi1 kernel: st 5:0:1:0: Device offlined
- not
ready after error recovery
Sep 27 11:03:27 genepi1 kernel: scsi 5:0:1:1: Device
offlined - not
ready after error recovery
Sep 27 11:07:00 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
(0x03:0x010D):
Invalid field in CDB:.
Sep 27 11:07:00 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
(0x03:0x0101):
Invalid command opcode:opcode=0xB8.
Sep 27 11:07:00 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
(0x03:0x0101):
Invalid command opcode:opcode=0xB8.
Sep 27 11:16:41 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
(0x03:0x010D):
Invalid field in CDB:.
Sep 27 11:16:41 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
(0x03:0x0101):
Invalid command opcode:opcode=0xB8.
Sep 27 11:16:41 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
(0x03:0x0101):
Invalid command opcode:opcode=0xB8.
Sep 27 11:16:51 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
(0x03:0x010D):
Invalid field in CDB:.
Sep 27 11:16:51 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
(0x03:0x0101):
Invalid command opcode:opcode=0xB8.
Sep 27 11:16:51 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
(0x03:0x0101):
Invalid command opcode:opcode=0xB8.
27 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5] SHADDR =
0x00, SHCNT = 0x0
Sep 27 11:03:27 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
CCSGCTL[0x10]
Sep 27 11:03:27 genepi1 kernel:
I have the Adaptec 29160 Ultra160 with 2 scsi HDs
I've never had any trouble since I installed these in 2001.
I have installed F5 through F9 but never had much luck with updating Fn to Fn+1
Educate me..I am learning. why the
mtx -d /dev/changer status
(/dev/changer a symlink to /dev/sg6)
I do a man mtx and get nothing!
--
fedora-list mailing list
fedora-list(a)redhat.com
To unsubscribe:
https://www.redhat.com/mailman/listinfo/fedora-list
Guidelines:
http://fedoraproject.org/wiki/Communicate/MailingListGuidelines
10:03 p.m.
--- On Tue, 9/30/08, gary artim <gartim(a)gmail.com> wrote:
From: gary artim <gartim(a)gmail.com>
Subject: Adaptec 29160 Ultra160 problem -- Fedora 9 install.
To: fedora-list(a)redhat.com
Date: Tuesday, September 30, 2008, 12:49 AM
Hi --
Installed fc9 on a server from fc8 and had a scsi
controller Adaptec
29160 Ultra160 SCSI adapter
give me grief. It's used with an lto autochanger. When
I entered:
mtx -d /dev/changer status
(/dev/changer a symlink to /dev/sg6)
It hung for a while, (a huge listing follows, sorry about
this), then
kernel messages gallor.
Anyway I tried reseating the card, moving the card to an
alternate
slot, checking the cabling, reboot the autochanger,
reboot the system --all did _not_ help.
I pulled the card and replaced it with a Adaptec AIC-7892A
U160/m (rev
02) and the autochanger and lto drive worked.
I also had to swap cables because of the interface
differences.
Long story, but can anyone say that this card looks broken?
It has a 5
year warranty and would like to get it replaced if so. Or
is
it a driver issue/I couldn't find a direct hit
searching the web or in
the archives?
I think my head is still sore from banging it against the
autochanger!
Thanks for _any_ help!
-- Gary
Sep 27 10:30:15 genepi1 kernel: scsi5 : Adaptec AIC79XX
PCI-X SCSI HBA
DRIVER, Rev 3.0
Sep 27 10:30:15 genepi1 kernel: <Adaptec 29320ALP
PCIx Ultra320
SCSI adapter>
Sep 27 10:30:15 genepi1 kernel: aic7901: Ultra320
Wide Channel
A, SCSI Id=7, PCI-X 101-133Mhz, 512 SCBs
Sep 27 10:30:15 genepi1 kernel: ACPI: PCI Interrupt
0000:04:01.0[A] ->
GSI 16 (level, low) -> IRQ 16
Sep 27 10:30:15 genepi1 kernel: e1000: 0000:04:01.0:
e1000_probe:
(PCI:66MHz:32-bit) 00:0e:0c:d9:8d:54
Sep 27 10:30:15 genepi1 kernel: scsi 5:0:1:0:
Sequential-Access HP
Ultrium 4-SCSI B12H PQ: 0 ANSI: 5
Sep 27 10:30:15 genepi1 kernel: scsi target5:0:1:
asynchronous
Sep 27 10:30:15 genepi1 kernel: scsi5:A:1:0: Tagged Queuing
enabled. Depth 4
Sep 27 10:30:15 genepi1 kernel: scsi target5:0:1: Beginning
Domain Validation
Sep 27 10:30:15 genepi1 kernel: scsi target5:0:1: wide
asynchronous
Sep 27 10:30:15 genepi1 kernel: scsi target5:0:1: FAST-160
WIDE SCSI
320.0 MB/s DT IU RTI PCOMP (6.25 ns, offset 64)
Sep 27 10:30:15 genepi1 kernel: scsi target5:0:1: Domain
Validation
skipping write tests
Sep 27 10:30:15 genepi1 kernel: scsi target5:0:1: Ending
Domain Validation
Sep 27 10:30:15 genepi1 kernel: scsi 5:0:1:1: Medium
Changer
OVERLAND NEO Series 0504 PQ: 0 ANSI: 5
Sep 27 10:30:15 genepi1 kernel: scsi5:A:1:1: Tagged Queuing
enabled. Depth 4
Sep 27 10:30:15 genepi1 kernel: e1000: eth2: e1000_probe:
Intel(R)
PRO/1000 Network Connection
Sep 27 10:30:15 genepi1 kernel: device-mapper: uevent:
version 1.0.3
Sep 27 10:30:15 genepi1 kernel: device-mapper: ioctl:
4.13.0-ioctl
(2007-10-18) initialised: dm-devel(a)redhat.com
Sep 27 10:30:15 genepi1 kernel: device-mapper: multipath:
version 1.0.5 loaded
Sep 27 10:30:15 genepi1 kernel: EXT3 FS on sda1, internal
journal
Sep 27 10:30:15 genepi1 kernel: Adding 25165812k swap on
/dev/sda2.
Priority:-1 extents:1 across:25165812k
Sep 27 10:30:15 genepi1 kernel: firmware: requesting
intel-ucode/06-0f-06
Sep 27 10:30:15 genepi1 kernel: firmware: requesting
intel-ucode/06-0f-06
Sep 27 10:30:15 genepi1 kernel: firmware: requesting
intel-ucode/06-0f-06
Sep 27 10:30:15 genepi1 kernel: firmware: requesting
intel-ucode/06-0f-06
Sep 27 10:30:15 genepi1 kernel: IA-32 Microcode Update
Driver: v1.14a
<tigran(a)aivazian.fsnet.co.uk>
Sep 27 10:30:15 genepi1 kernel: microcode: CPU0 updated
from revision
0x44 to 0xcd, date = 09162007
Sep 27 10:30:15 genepi1 kernel: microcode: CPU1 updated
from revision
0x44 to 0xcd, date = 09162007
Sep 27 10:30:15 genepi1 kernel: microcode: CPU2 updated
from revision
0x44 to 0xcd, date = 09162007
Sep 27 10:30:15 genepi1 kernel: microcode: CPU3 updated
from revision
0x44 to 0xcd, date = 09162007
Sep 27 10:30:15 genepi1 kernel: scsi 5:0:1:0: Attached scsi
generic sg5 type 1
Sep 27 10:30:15 genepi1 kernel: scsi 5:0:1:1: Attached scsi
generic sg6 type 8
Sep 27 10:30:15 genepi1 kernel: osst :I: Tape driver with
OnStream
support version 0.99.4
Sep 27 10:30:15 genepi1 kernel: osst :I: $Id: osst.c,v 1.73
2005/01/01
21:13:34 wriede Exp $
Sep 27 10:30:15 genepi1 kernel: Driver 'osst' needs
updating - please
use bus_type methods
Sep 27 10:30:15 genepi1 kernel: st: Version 20080224, fixed
bufsize
32768, s/g segs 256
Sep 27 10:30:15 genepi1 kernel: Driver 'st' needs
updating - please
use bus_type methods
Sep 27 10:30:15 genepi1 kernel: st 5:0:1:0: Attached scsi
tape st0
Sep 27 10:30:15 genepi1 kernel: st 5:0:1:0: st0: try direct
i/o: yes
(alignment 4 B)
Sep 27 10:30:15 genepi1 kernel: eth0: Link is Up 1000 Mbps
Full
Duplex, Flow Control: RX
Sep 27 10:30:15 genepi1 kernel: ADDRCONF(NETDEV_CHANGE):
eth0: link
becomes ready
Sep 27 10:30:15 genepi1 kernel: ADDRCONF(NETDEV_UP): eth1:
link is not ready
Sep 27 10:54:58 genepi1 yum: Installed:
mtx-1.3.12-1.fc9.x86_64
Sep 27 10:58:19 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
(0x03:0x010D):
Invalid field in CDB:.
Sep 27 10:58:19 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
(0x03:0x0101):
Invalid command opcode:opcode=0xB8.
Sep 27 10:58:19 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
(0x03:0x0101):
Invalid command opcode:opcode=0xB8.
Sep 27 11:02:27 genepi1 kernel: st 5:0:1:0: Attempting to
queue an
ABORT message:CDB: 0x12 0x0 0x0 0x0 0x38 0x0
Sep 27 11:02:27 genepi1 kernel: scsi5: At time of recovery,
card was not paused
Sep 27 11:02:27 genepi1 kernel:
>>>>>>>>>>>>>>>>>>
Dump Card State
Begins
<<<<<<<<<<<<<<<<<
Sep 27 11:02:27 genepi1 kernel: scsi5: Dumping Card State
at program
address 0x34 Mode 0x22
Sep 27 11:02:27 genepi1 kernel: Card was paused
Sep 27 11:02:27 genepi1Sep 27 11:02:27 genepi1 kernel:
INTSTAT[0x0]
SELOID[0x1] SELID[0x10] HS_MAILBOX[0x0]
Sep 27 11:02:27 genepi1 kernel: INTCTL[0x80]
SEQINTSTAT[0x0]
SAVED_MODE[0x11] DFFSTAT[0x33]
Sep 27 11:02:27 genepi1 kernel: SCSISIGI[0x0]
SCSIPHASE[0x0]
SCSIBUS[0x0] LASTPHASE[0x1]
Sep 27 11:02:27 genepi1 kernel: SCSISEQ0[0x0]
SCSISEQ1[0x12]
SEQCTL0[0x0] SEQINTCTL[0x0]
Sep 27 11:02:27 genepi1 kernel: SEQ_FLAGS[0x0]
SEQ_FLAGS2[0x4]
QFREEZE_COUNT[0x7]
Sep 27 11:02:27 genepi1 kernel: KERNEL_QFREEZE_COUNT[0x6]
MK_MESSAGE_SCB[0xff00]
Sep 27 11:02:27 genepi1 kernel: MK_MESSAGE_SCSIID[0xff]
SSTAT0[0x0] SSTAT1[0x8]
Sep 27 11:02:27 genepi1 kernel: SSTAT2[0x0] SSTAT3[0x0]
PERRDIAG[0x0]
SIMODE1[0xa4]
Sep 27 11:02:27 genepi1 kernel: LQISTAT0[0x0] LQISTAT1[0x0]
LQISTAT2[0x0] LQOSTAT0[0x0]
Sep 27 11:02:27 genepi1 kernel: LQOSTAT1[0x0]
LQOSTAT2[0xe1]
Sep 27 11:02:27 genepi1 kernel:
Sep 27 11:02:27 genepi1 kernel: SCB Count = 4 CMDS_PENDING
= 0 LASTSCB
0xffff CURRSCB 0x3 NEXTSCB 0xff80
Sep 27 11:02:27 genepi1 kernel: qinstart = 44 qinfifonext =
46
Sep 27 11:02:27 genepi1 kernel: QINFIFO: 0x3 0x2
Sep 27 11:02:27 genepi1 kernel: WAITING_TID_QUEUES:
Sep 27 11:02:27 genepi1 kernel: Pending list:
Sep 27 11:02:27 genepi1 kernel: 2 FIFO_USE[0x0]
SCB_CONTROL[0x68]
SCB_SCSIID[0x17]
Sep 27 11:02:27 genepi1 kernel: 3 FIFO_USE[0x2]
SCB_CONTROL[0x68]
SCB_SCSIID[0x17]
Sep 27 11:02:27 genepi1 kernel: Total 2
Sep 27 11:02:27 genepi1 kernel: Kernel Free SCB list: 1 0
Sep 27 11:02:27 genepi1 kernel: Sequencer Complete
DMA-inprog list:
Sep 27 11:02:27 genepi1 kernel: Sequencer Complete list:
Sep 27 11:02:27 genepi1 kernel: Sequencer DMA-Up and
Complete list:
Sep 27 11:02:27 genepi1 kernel: Sequencer On QFreeze and
Complete list:
Sep 27 11:02:27 genepi1 kernel:
Sep 27 11:02:27 genepi1 kernel:
Sep 27 11:02:27 genepi1 kernel: scsi5: FIFO0 Free, LONGJMP
== 0x82a3, SCB 0x3
Sep 27 11:02:27 genepi1 kernel: SEQIMODE[0x3f]
SEQINTSRC[0x0]
DFCNTRL[0x0] DFSTATUS[0x89]
Sep 27 11:02:27 genepi1 kernel: SG_CACHE_SHADOW[0x2]
SG_STATE[0x0]
DFFSXFRCTL[0x0]
Sep 27 11:02:27 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
SHADDR =
0x00, SHCNT = 0x0
Sep 27 11:02:27 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
CCSGCTL[0x10]
Sep 27 11:02:27 genepi1 kernel:
Sep 27 11:02:27 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP
== 0x8063, SCB 0x3
Sep 27 11:02:27 genepi1 kernel: SEQIMODE[0x3f]
SEQINTSRC[0x0]
DFCNTRL[0x0] DFSTATUS[0x89]
Sep 27 11:02:27 genepi1 kernel: SG_CACHE_SHADOW[0x2]
SG_STATE[0x0]
DFFSXFRCTL[0x0]
Sep 27 11:02:27 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
SHADDR =
0x00, SHCNT = 0x0
Sep 27 11:02:27 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
CCSGCTL[0x10]
Sep 27 11:02:27 genepi1 kernel: LQIN: 0x8 0x0 0x0 0x3 0x0
0x1 0x0 0x0
0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
Sep 27 11:02:27 genepi1 kernel: scsi5: LQISTATE = 0x0,
LQOSTATE = 0x0,
OPTIONMODE = 0x52
Sep 27 11:02:27 genepi1 kernel: scsi5: OS_SPACE_CNT = 0x20
MAXCMDCNT = 0x1
Sep 27 11:02:27 genepi1 kernel: scsi5: SAVED_SCSIID = 0x0
SAVED_LUN = 0x0
Sep 27 11:02:27 genepi1 kernel: SIMODE0[0xc]
Sep 27 11:02:27 genepi1 kernel: CCSCBCTL[0x0]
Sep 27 11:02:27 genepi1 kernel: scsi5: REG0 == 0x3, SINDEX
= 0x104,
DINDEX = 0x104
Sep 27 11:02:27 genepi1 kernel: scsi5: SCBPTR == 0x3,
SCB_NEXT ==
0xff80, SCB_NEXT2 == 0xff80
Sep 27 11:02:27 genepi1 kernel: CDB 3 0 0 83 a 8c
Sep 27 11:02:27 genepi1 kernel: STACK: 0x20 0x0 0x0 0x0 0x0
0x0 0x0 0x0
Sep 27 11:02:27 genepi1 kernel:
<<<<<<<<<<<<<<<<<
Dump Card State Ends
>>>>>>>>>>>>>>>>>>
Sep 27 11:02:27 genepi1 kernel: scsi5:0:1:0: Cmd aborted
from QINFIFO
Sep 27 11:02:37 genepi1 kernel: st 5:0:1:0: Attempting to
queue an
ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
Sep 27 11:02:37 genepi1 kernel: scsi5: At time of recovery,
card was not paused
Sep 27 11:02:37 genepi1 kernel:
>>>>>>>>>>>>>>>>>>
Dump Card State
Begins
<<<<<<<<<<<<<<<<<
Sep 27 11:02:37 genepi1 kernel: scsi5: Dumping Card State
at program
address 0x18 Mode 0x33
kernel: INTSTAT[0x0] SELOID[0x1] SELID[0x10]
HS_MAILBOX[0x0]
Sep 27 11:02:27 genepi1 kernel: INTCTL[0x80]
SEQINTSTAT[0x0]
SAVED_MODE[0x11] DFFSTAT[0x33]
Sep 27 11:02:37 genepi1 kernel:
>>>>>>>>>>>>>>>>>>
Dump Card State
Begins
<<<<<<<<<<<<<<<<<
Sep 27 11:02:37 genepi1 kernel: scsi5: Dumping Card State
at program
address 0x18 Mode 0x33
Sep 27 11:02:37 genepi1 kernel: Card was paused
Sep 27 11:02:37 genepi1 kernel: INTSTAT[0x0] SELOID[0x1]
SELID[0x10]
HS_MAILBOX[0x0]
Sep 27 11:02:37 genepi1 kernel: INTCTL[0x80]
SEQINTSTAT[0x0]
SAVED_MODE[0x11] DFFSTAT[0x33]
Sep 27 11:02:37 genepi1 kernel: SCSISIGI[0x0]
SCSIPHASE[0x0]
SCSIBUS[0x0] LASTPHASE[0x1]
Sep 27 11:02:37 genepi1 kernel: SCSISEQ0[0x0]
SCSISEQ1[0x12]
SEQCTL0[0x0] SEQINTCTL[0x0]
Sep 27 11:02:37 genepi1 kernel: SEQ_FLAGS[0x0]
SEQ_FLAGS2[0x4]
QFREEZE_COUNT[0x7]
Sep 27 11:02:37 genepi1 kernel: KERNEL_QFREEZE_COUNT[0x6]
MK_MESSAGE_SCB[0xff00]
Sep 27 11:02:37 genepi1 kernel: MK_MESSAGE_SCSIID[0xff]
SSTAT0[0x0] SSTAT1[0x0]
Sep 27 11:02:37 genepi1 kernel: SSTAT2[0x0] SSTAT3[0x0]
PERRDIAG[0x0]
SIMODE1[0xa4]
Sep 27 11:02:37 genepi1 kernel: LQISTAT0[0x0] LQISTAT1[0x0]
LQISTAT2[0x0] LQOSTAT0[0x0]
Sep 27 11:02:37 genepi1 kernel: LQOSTAT1[0x0]
LQOSTAT2[0xe1]
Sep 27 11:02:37 genepi1 kernel:
Sep 27 11:02:37 genepi1 kernel: SCB Count = 4 CMDS_PENDING
= 0 LASTSCB
0xffff CURRSCB 0x3 NEXTSCB 0xff80
Sep 27 11:02:37 genepi1 kernel: qinstart = 44 qinfifonext =
46
Sep 27 11:02:37 genepi1 kernel: QINFIFO: 0x3 0x2
Sep 27 11:02:37 genepi1 kernel: WAITING_TID_QUEUES:
Sep 27 11:02:37 genepi1 kernel: Pending list:
Sep 27 11:02:37 genepi1 kernel: 2 FIFO_USE[0x0]
SCB_CONTROL[0x68]
SCB_SCSIID[0x17]
Sep 27 11:02:37 genepi1 kernel: 3 FIFO_USE[0x2]
SCB_CONTROL[0x68]
SCB_SCSIID[0x17]
Sep 27 11:02:37 genepi1 kernel: Total 2
Sep 27 11:02:37 genepi1 kernel: Kernel Free SCB list: 1 0
Sep 27 11:02:37 genepi1 kernel: Sequencer Complete
DMA-inprog list:
Sep 27 11:02:37 genepi1 kernel: Sequencer Complete list:
Sep 27 11:02:37 genepi1 kernel: Sequencer DMA-Up and
Complete list:
Sep 27 11:02:37 genepi1 kernel: Sequencer On QFreeze and
Complete list:
Sep 27 11:02:37 genepi1 kernel:
Sep 27 11:02:37 genepi1 kernel:
Sep 27 11:02:37 genepi1 kernel: scsi5: FIFO0 Free, LONGJMP
== 0x82a3, SCB 0x3
Sep 27 11:02:37 genepi1 kernel: SEQIMODE[0x3f]
SEQINTSRC[0x0]
DFCNTRL[0x0] DFSTATUS[0x89]
Sep 27 11:02:37 genepi1 kernel: SG_CACHE_SHADOW[0x2]
SG_STATE[0x0]
DFFSXFRCTL[0x0]
Sep 27 11:02:37 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
SHADDR =
0x00, SHCNT = 0x0
Sep 27 11:02:37 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
CCSGCTL[0x10]
Sep 27 11:02:37 genepi1 kernel:
Sep 27 11:02:37 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP
== 0x8063, SCB 0x3
Sep 27 11:02:37 genepi1 kernel: SEQIMODE[0x3f]
SEQINTSRC[0x0]
DFCNTRL[0x0] DFSTATUS[0x89]
Sep 27 11:02:37 genepi1 kernel: SG_CACHE_SHADOW[0x2]
SG_STATE[0x0]
DFFSXFRCTL[0x0]
Sep 27 11:02:37 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
SHADDR =
0x00, SHCNT = 0x0
Sep 27 11:02:37 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
CCSGCTL[0x10]
Sep 27 11:02:37 genepi1 kernel: LQIN: 0x8 0x0 0x0 0x3 0x0
0x1 0x0 0x0
0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
Sep 27 11:02:37 genepi1 kernel: scsi5: LQISTATE = 0x0,
LQOSTATE = 0x0,
OPTIONMODE = 0x52
Sep 27 11:02:37 genepi1 kernel: scsi5: OS_SPACE_CNT = 0x20
MAXCMDCNT = 0x1
Sep 27 11:02:37 genepi1 kernel: scsi5: SAVED_SCSIID = 0x0
SAVED_LUN = 0x0
Sep 27 11:02:37 genepi1 kernel: SIMODE0[0xc]
Sep 27 11:02:37 genepi1 kernel: CCSCBCTL[0x0]
Sep 27 11:02:37 genepi1 kernel: scsi5: REG0 == 0xffff,
SINDEX = 0x104,
DINDEX = 0x104
Sep 27 11:02:37 genepi1 kernel: scsi5: SCBPTR == 0x3,
SCB_NEXT ==
0xff80, SCB_NEXT2 == 0xff80
Sep 27 11:02:37 genepi1 kernel: CDB 3 0 0 83 a 8c
Sep 27 11:02:37 genepi1 kernel: STACK: 0x0 0x0 0x0 0x0 0x0
0x0 0x0 0x0
Sep 27 11:02:37 Sep 27 11:02:37 genepi1 kernel:
scsi5:0:1:0: Cmd
aborted from QINFIFO
Sep 27 11:02:37 genepi1 kernel: scsi 5:0:1:1: Attempting to
queue an
ABORT message:CDB: 0x1a 0x8 0x1d 0x0 0x88 0x0
Sep 27 11:02:37 genepi1 kernel: scsi5: At time of recovery,
card was not paused
Sep 27 11:02:37 genepi1 kernel:
>>>>>>>>>>>>>>>>>>
Dump Card State
Begins
<<<<<<<<<<<<<<<<<
Sep 27 11:02:37 genepi1 kernel: scsi5: Dumping Card State
at program
address 0x31 Mode 0x11
Sep 27 11:02:37 genepi1 kernel: Card was paused
Sep 27 11:02:37 genepi1 kernel: INTSTAT[0x0] SELOID[0x1]
SELID[0x10]
HS_MAILBOX[0x0]
Sep 27 11:02:37 genepi1 kernel: INTCTL[0x80]
SEQINTSTAT[0x0]
SAVED_MODE[0x11] DFFSTAT[0x33]
Sep 27 11:02:37 genepi1 kernel: SCSISIGI[0x0]
SCSIPHASE[0x0]
SCSIBUS[0x0] LASTPHASE[0x1]
Sep 27 11:02:37 genepi1 kernel: SCSISEQ0[0x0]
SCSISEQ1[0x12]
SEQCTL0[0x0] SEQINTCTL[0x0]
Sep 27 11:02:37 genepi1 kernel: SEQ_FLAGS[0x0]
SEQ_FLAGS2[0x4]
QFREEZE_COUNT[0x7]
Sep 27 11:02:37 genepi1 kernel: KERNEL_QFREEZE_COUNT[0x6]
MK_MESSAGE_SCB[0xff00]
Sep 27 11:02:37 genepi1 kernel: MK_MESSAGE_SCSIID[0xff]
SSTAT0[0x0] SSTAT1[0x0]
Sep 27 11:02:37 genepi1 kernel: SSTAT2[0x0] SSTAT3[0x0]
PERRDIAG[0x0]
SIMODE1[0xa4]
Sep 27 11:02:37 genepi1 kernel: LQISTAT0[0x0] LQISTAT1[0x0]
LQISTAT2[0x0] LQOSTAT0[0x0]
Sep 27 11:02:37 genepi1 kernel: LQOSTAT1[0x0]
LQOSTAT2[0xe1]
Sep 27 11:02:37 genepi1 kernel:
Sep 27 11:02:37 genepi1 kernel: SCB Count = 4 CMDS_PENDING
= 0 LASTSCB
0xffff CURRSCB 0x3 NEXTSCB 0xff80
Sep 27 11:02:37 genepi1 kernel: qinstart = 44 qinfifonext =
45
Sep 27 11:02:37 genepi1 kernel: QINFIFO: 0x3
Sep 27 11:02:37 genepi1 kernel: WAITING_TID_QUEUES:
Sep 27 11:02:37 genepi1 kernel: Pending list:
Sep 27 11:02:37 genepi1 kernel: 3 FIFO_USE[0x0]
SCB_CONTROL[0x68]
SCB_SCSIID[0x17]
Sep 27 11:02:37 genepi1 kernel: Total 1
Sep 27 11:02:37 genepi1 kernel: Kernel Free SCB list: 2 1 0
Sep 27 11:02:37 genepi1 kernel: Sequencer Complete
DMA-inprog list:
Sep 27 11:02:37 genepi1 kernel: Sequencer Complete list:
Sep 27 11:02:37 genepi1 kernel: Sequencer DMA-Up and
Complete list:
Sep 27 11:02:37 genepi1 kernel: Sequencer On QFreeze and
Complete list:
Sep 27 11:02:37 genepi1 kernel:
Sep 27 11:02:37 genepi1 kernel:
Sep 27 11:02:37 genepi1 kernel: scsi5: FIFO0 Free, LONGJMP
== 0x82a3, SCB 0x3
Sep 27 11:02:37 genepi1 kernel: SEQIMODE[0x3f]
SEQINTSRC[0x0]
DFCNTRL[0x0] DFSTATUS[0x89]
Sep 27 11:02:37 genepi1 kernel: SG_CACHE_SHADOW[0x2]
SG_STATE[0x0]
DFFSXFRCTL[0x0]
Sep 27 11:02:37 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
SHADDR =
0x00, SHCNT = 0x0
Sep 27 11:02:37 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
CCSGCTL[0x10]
Sep 27 11:02:37 genepi1 kernel:
Sep 27 11:02:37 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP
== 0x8063, SCB 0x3
Sep 27 11:02:37 genepi1 kernel: SEQIMODE[0x3f]
SEQINTSRC[0x0]
DFCNTRL[0x0] DFSTATUS[0x89]
Sep 27 11:02:37 genepi1 kernel: SG_CACHE_SHADOW[0x2]
SG_STATE[0x0]
DFFSXFRCTL[0x0]
Sep 27 11:02:37 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
SHADDR =
0x00, SHCNT = 0x0
Sep 27 11:02:37 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
CCSGCTL[0x10]
Sep 27 11:02:37 genepi1 kernel: LQIN: 0x8 0x0 0x0 0x3 0x0
0x1 0x0 0x0
0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
Sep 27 11:02:37 genepi1 kernel: scsi5: LQISTATE = 0x0,
LQOSTATE = 0x0,
OPTIONMODE = 0x52
Sep 27 11:02:37 genepi1 kernel: scsi5: OS_SPACE_CNT = 0x20
MAXCMDCNT = 0x1
Sep 27 11:02:37 genepi1 kernel: scsi5: SAVED_SCSIID = 0x0
SAVED_LUN = 0x0
Sep 27 11:02:37 genepi1 kernel: SIMODE0[0xc]
Sep 27 11:02:37 genepi1 kernel: CCSCBCTL[0x0]
Sep 27 11:02:37 genepi1 kernel: scsi5: REG0 == 0x3, SINDEX
= 0x104,
DINDEX = 0x104
Sep 27 11:02:37 genepi1 kernel: scsi5: SCBPTR == 0x3,
SCB_NEXT ==
0xff80, SCB_NEXT2 == 0xff80
Sep 27 11:02:37 genepi1 kernel: CDB 3 0 0 83 a 8c
Sep 27 11:02:37 genepi1 kernel: STACK: 0x1f 0x0 0x0 0x0 0x0
0x0 0x0 0x0
Sep 27 11:02:37 genepi1 kernel:
<<<<<<<<<<<<<<<<<
Dump Card State Ends
>>>>>>>>>>>>>>>>>>
genepi1 kernel:
<<<<<<<<<<<<<<<<<
Dump Card State Ends
>>>>>>>>>>>>>>>>>>
Sep 27 11:02:37 genepi1 kernel: scsi5:0:1:0: Cmd aborted
from QINFIFO
Sep 27 11:02:37 genepi1 kernel: scsi 5:0:1:1: Attempting to
queue an
ABORT message:CDB: 0x1a 0x8 0x1d 0x0 0x88 0x0
Sep 27 11:02:37 genepi1 kernel: scsi5:0:1:0: Cmd aborted
from QINFIFO
Sep 27 11:02:37 genepi1 kernel: scsi 5:0:1:1: Attempting to
queue an
ABORT message:CDB: 0x1a 0x8 0x1d 0x0 0x88 0x0
Sep 27 11:02:37 genepi1 kernel: scsi5: At time of recovery,
card was not paused
Sep 27 11:02:37 genepi1 kernel:
>>>>>>>>>>>>>>>>>>
Dump Card State
Begins
<<<<<<<<<<<<<<<<<
Sep 27 11:02:37 genepi1 kernel: scsi5: Dumping Card State
at program
address 0x31 Mode 0x11
Sep 27 11:02:37 genepi1 kernel: Card was paused
Sep 27 11:02:37 genepi1 kernel: INTSTAT[0x0] SELOID[0x1]
SELID[0x10]
HS_MAILBOX[0x0]
Sep 27 11:02:37 genepi1 kernel: INTCTL[0x80]
SEQINTSTAT[0x0]
SAVED_MODE[0x11] DFFSTAT[0x33]
Sep 27 11:02:37 genepi1 kernel: SCSISIGI[0x0]
SCSIPHASE[0x0]
SCSIBUS[0x0] LASTPHASE[0x1]
Sep 27 11:02:37 genepi1 kernel: SCSISEQ0[0x0]
SCSISEQ1[0x12]
SEQCTL0[0x0] SEQINTCTL[0x0]
Sep 27 11:02:37 genepi1 kernel: SEQ_FLAGS[0x0]
SEQ_FLAGS2[0x4]
QFREEZE_COUNT[0x7]
Sep 27 11:02:37 genepi1 kernel: KERNEL_QFREEZE_COUNT[0x6]
MK_MESSAGE_SCB[0xff00]
Sep 27 11:02:37 genepi1 kernel: MK_MESSAGE_SCSIID[0xff]
SSTAT0[0x0] SSTAT1[0x0]
Sep 27 11:02:37 genepi1 kernel: SSTAT2[0x0] SSTAT3[0x0]
PERRDIAG[0x0]
SIMODE1[0xa4]
Sep 27 11:02:37 genepi1 kernel: LQISTAT0[0x0] LQISTAT1[0x0]
LQISTAT2[0x0] LQOSTAT0[0x0]
Sep 27 11:02:37 genepi1 kernel: LQOSTAT1[0x0]
LQOSTAT2[0xe1]
Sep 27 11:02:37 genepi1 kernel:
Sep 27 11:02:37 genepi1 kernel: SCB Count = 4 CMDS_PENDING
= 0 LASTSCB
0xffff CURRSCB 0x3 NEXTSCB 0xff80
Sep 27 11:02:37 genepi1 kernel: qinstart = 44 qinfifonext =
45
Sep 27 11:02:37 genepi1 kernel: QINFIFO: 0x3
Sep 27 11:02:37 genepi1 kernel: WAITING_TID_QUEUES:
Sep 27 11:02:37 genepi1 kernel: Pending list:
Sep 27 11:02:37 genepi1 kernel: 3 FIFO_USE[0x0]
SCB_CONTROL[0x68]
SCB_SCSIID[0x17]
Sep 27 11:02:37 genepi1 kernel: Total 1
Sep 27 11:02:37 genepi1 kernel: Kernel Free SCB list: 2 1 0
Sep 27 11:02:37 genepi1 kernel: Sequencer Complete
DMA-inprog list:
Sep 27 11:02:37 genepi1 kernel: Sequencer Complete list:
Sep 27 11:02:37 genepi1 kernel: Sequencer DMA-Up and
Complete list:
Sep 27 11:02:37 genepi1 kernel: Sequencer On QFreeze and
Complete list:
Sep 27 11:02:37 genepi1 kernel:
Sep 27 11:02:37 genepi1 kernel:
Sep 27 11:02:37 genepi1 kernel: scsi5: FIFO0 Free, LONGJMP
== 0x82a3, SCB 0x3
Sep 27 11:02:37 genepi1 kernel: SEQIMODE[0x3f]
SEQINTSRC[0x0]
DFCNTRL[0x0] DFSTATUS[0x89]
Sep 27 11:02:37 genepi1 kernel: SG_CACHE_SHADOW[0x2]
SG_STATE[0x0]
DFFSXFRCTL[0x0]
Sep 27 11:02:37 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
SHADDR =
0x00, SHCNT = 0x0
Sep 27 11:02:37 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
CCSGCTL[0x10]
Sep 27 11:02:37 genepi1 kernel:
Sep 27 11:02:37 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP
== 0x8063, SCB 0x3
Sep 27 11:02:37 genepi1 kernel: SEQIMODE[0x3f]
SEQINTSRC[0x0]
DFCNTRL[0x0] DFSTATUS[0x89]
Sep 27 11:02:37 genepi1 kernel: SG_CACHE_SHADOW[0x2]
SG_STATE[0x0]
DFFSXFRCTL[0x0]
Sep 27 11:02:37 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
SHADDR =
0x00, SHCNT = 0x0
Sep 27 11:02:37 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
CCSGCTL[0x10]
Sep 27 11:02:37 genepi1 kernel: LQIN: 0x8 0x0 0x0 0x3 0x0
0x1 0x0 0x0
0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
Sep 27 11:02:37 genepi1 kernel: scsi5: LQISTATE = 0x0,
LQOSTATE = 0x0,
OPTIONMODE = 0x52
Sep 27 11:02:37 genepi1 kernel: scsi5: OS_SPACE_CNT = 0x20
MAXCMDCNT = 0x1
Sep 27 11:02:37 genepi1 kernel: scsi5: SAVED_SCSIID = 0x0
SAVED_LUN = 0x0
Sep 27 11:02:37 genepi1 kernel: SIMODE0[0xc]
Sep 27 11:02:37 genepi1 kernel: CCSCBCTL[0x0]
Sep 27 11:02:37 genepi1 kernel: scsi5: REG0 == 0x3, SINDEX
= 0x104,
DINDEX = 0x104
Sep 27 11:02:37 genepi1 kernel: scsi5: SCBPTR == 0x3,
SCB_NEXT ==
0xff80, SCB_NEXT2 == 0xff80
Sep 27 11:02:37 genepi1 kernel: CDB 3 0 0 83 a 8c
Sep 27 11:02:37 genepi1 kernel: STACK: 0x1f 0x0 0x0 0x0 0x0
0x0 0x0 0x0
Sep 27 11:02:37 genepi1 kernel:
<<<<<<<<<<<<<<<<<
Dump Card State Ends
>>>>>>>>>>>>>>>>>>
Sep 27 11:02:37 genepi1 kernel: STACK: 0x1f 0x0 0x0 0x0 0x0
0x0 0x0 0x0
Sep 27 11:02:37 genepi1 kernel:
<<<<<<<<<<<<<<<<<
Dump Card State Ends
>>>>>>>>>>>>>>>>>>
Sep 27 11:02:37 genepi1 kernel: scsi5:0:1:1: Cmd aborted
from QINFIFO
Sep 27 11:02:47 genepi1 kernel: scsi 5:0:1:1: Attempting to
queue an
ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
Sep 27 11:02:47 genepi1 kernel: scsi5: At time of recovery,
card was not paused
Sep 27 11:02:47 genepi1 kernel:
>>>>>>>>>>>>>>>>>>
Dump Card State
Begins
<<<<<<<<<<<<<<<<<
Sep 27 11:02:47 genepi1 kernel: scsi5: Dumping Card State
at program
address 0x18 Mode 0x33
Sep 27 11:02:47 genepi1 kernel: Card was paused
Sep 27 11:02:47 genepi1 kernel: INTSTAT[0x0] SELOID[0x1]
SELID[0x10]
HS_MAILBOX[0x0]
Sep 27 11:02:47 genepi1 kernel: INTCTL[0x80]
SEQINTSTAT[0x0]
SAVED_MODE[0x11] DFFSTAT[0x33]
Sep 27 11:02:47 genepi1 kernel: SCSISIGI[0x0]
SCSIPHASE[0x0]
SCSIBUS[0x0] LASTPHASE[0x1]
Sep 27 11:02:47 genepi1 kernel: SCSISEQ0[0x0]
SCSISEQ1[0x12]
SEQCTL0[0x0] SEQINTCTL[0x0]
Sep 27 11:02:47 genepi1 kernel: SEQ_FLAGS[0x0]
SEQ_FLAGS2[0x4]
QFREEZE_COUNT[0x7]
Sep 27 11:02:47 genepi1 kernel: KERNEL_QFREEZE_COUNT[0x6]
MK_MESSAGE_SCB[0xff00]
Sep 27 11:02:47 genepi1 kernel: MK_MESSAGE_SCSIID[0xff]
SSTAT0[0x0] SSTAT1[0x0]
Sep 27 11:02:47 genepi1 kernel: SSTAT2[0x0] SSTAT3[0x0]
PERRDIAG[0x0]
SIMODE1[0xa4]
Sep 27 11:02:47 genepi1 kernel: LQISTAT0[0x0] LQISTAT1[0x0]
LQISTAT2[0x0] LQOSTAT0[0x0]
Sep 27 11:02:47 genepi1 kernel: LQOSTAT1[0x0]
LQOSTAT2[0xe1]
Sep 27 11:02:47 genepi1 kernel:
Sep 27 11:02:47 genepi1 kernel: SCB Count = 4 CMDS_PENDING
= 0 LASTSCB
0xffff CURRSCB 0x3 NEXTSCB 0xff80
Sep 27 11:02:47 genepi1 kernel: qinstart = 44 qinfifonext =
45
Sep 27 11:02:47 genepi1 kernel: QINFIFO: 0x3
Sep 27 11:02:47 genepi1 kernel: WAITING_TID_QUEUES:
Sep 27 11:02:47 genepi1 kernel: Pending list:
Sep 27 11:02:47 genepi1 kernel: 3 FIFO_USE[0x0]
SCB_CONTROL[0x68]
SCB_SCSIID[0x17]
Sep 27 11:02:47 genepi1 kernel: Total 1
Sep 27 11:02:47 genepi1 kernel: Kernel Free SCB list: 2 1 0
Sep 27 11:02:47 genepi1 kernel: Sequencer Complete
DMA-inprog list:
Sep 27 11:02:47 genepi1 kernel: Sequencer Complete list:
Sep 27 11:02:47 genepi1 kernel: Sequencer DMA-Up and
Complete list:
Sep 27 11:02:47 genepi1 kernel: Sequencer On QFreeze and
Complete list:
Sep 27 11:02:47 genepi1 kernel:
Sep 27 11:02:47 genepi1 kernel:
Sep 27 11:02:47 genepi1 kernel: scsi5: FIFO0 Free, LONGJMP
== 0x82a3, SCB 0x3
Sep 27 11:02:47 genepi1 kernel: SEQIMODE[0x3f]
SEQINTSRC[0x0]
DFCNTRL[0x0] DFSTATUS[0x89]
Sep 27 11:02:47 genepi1 kernel: SG_CACHE_SHADOW[0x2]
SG_STATE[0x0]
DFFSXFRCTL[0x0]
Sep 27 11:02:47 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
SHADDR =
0x00, SHCNT = 0x0
Sep 27 11:02:47 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
CCSGCTL[0x10]
Sep 27 11:02:47 genepi1 kernel:
Sep 27 11:02:47 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP
== 0x8063, SCB 0x3
Sep 27 11:02:47 genepi1 kernel: SEQIMODE[0x3f]
SEQINTSRC[0x0]
DFCNTRL[0x0] DFSTATUS[0x89]
Sep 27 11:02:47 genepi1 kernel: SG_CACHE_SHADOW[0x2]
SG_STATE[0x0]
DFFSXFRCTL[0x0]
Sep 27 11:02:47 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
SHADDR =
0x00, SHCNT = 0x0
Sep 27 11:02:47 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
CCSGCTL[0x10]
Sep 27 11:02:47 genepi1 kernel: LQIN: 0x8 0x0 0x0 0x3 0x0
0x1 0x0 0x0
0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
Sep 27 11:02:47 genepi1 kernel: scsi5: LQISTATE = 0x0,
LQOSTATE = 0x0,
OPTIONMODE = 0x52
Sep 27 11:02:47 genepi1 kernel: scsi5: OS_SPACE_CNT = 0x20
MAXCMDCNT = 0x1
Sep 27 11:02:47 genepi1 kernel: scsi5: SAVED_SCSIID = 0x0
SAVED_LUN = 0x0
Sep 27 11:02:47 genepi1 kernel: SIMODE0[0xc]
Sep 27 11:02:47 genepi1 kernel: CCSCBCTL[0x0]
Sep 27 11:02:47 genepi1 kernel: scsi5: REG0 == 0xffff,
SINDEX = 0x104,
DINDEX = 0x104
Sep 27 11:02:47 genepi1 kernel: scsi5: SCBPTR == 0x3,
SCB_NEXT ==
0xff80, SCB_NEXT2 == 0xff80
Sep 27 11:02:47 genepi1 kernel: CDB 3 0 0 83 a 8c
Sep 27 11:02:47 genepi1 kernel: scsi5: SCBPTR == 0x3,
SCB_NEXT ==
0xff80, SCB_NEXT2 == 0xff80
Sep 27 11:02:47 genepi1 kernel: CDB 3 0 0 83 a 8c
Sep 27 11:02:47 genepi1 kernel: STACK: 0x0 0x0 0x0 0x0 0x0
0x0 0x0 0x0
Sep 27 11:02:47 genepi1 kernel:
<<<<<<<<<<<<<<<<<
Dump Card State Ends
>>>>>>>>>>>>>>>>>>
Sep 27 11:02:47 genepi1 kernel: scsi5:0:1:1: Cmd aborted
from QINFIFO
Sep 27 11:02:47 genepi1 kernel: st 5:0:1:0: Attempting to
queue a
TARGET RESET message:CDB: 0x12 0x0 0x0 0x0 0x38 0x0
Sep 27 11:02:47 genepi1 kernel: scsi5: Device reset code
sleeping
Sep 27 11:02:52 genepi1 kernel: scsi5: Device reset timer
expired (active 1)
Sep 27 11:02:52 genepi1 kernel: scsi5: Device reset
returning 0x2003
Sep 27 11:02:52 genepi1 kernel: scsi 5:0:1:1: Attempting to
queue a
TARGET RESET message:CDB: 0x1a 0x8 0x1d 0x0 0x88 0x0
Sep 27 11:02:52 genepi1 kernel: scsi5: Device reset code
sleeping
Sep 27 11:02:57 genepi1 kernel: scsi5: Device reset timer
expired (active 1)
Sep 27 11:02:57 genepi1 kernel: scsi5: Device reset
returning 0x2003
Sep 27 11:02:57 genepi1 kernel: Recovery SCB completes
Sep 27 11:02:57 genepi1 kernel: Recovery SCB completes
Sep 27 11:03:17 genepi1 kernel: st 5:0:1:0: Attempting to
queue an
ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
Sep 27 11:03:17 genepi1 kernel: scsi5: At time of recovery,
card was not paused
Sep 27 11:03:17 genepi1 kernel:
>>>>>>>>>>>>>>>>>>
Dump Card State
Begins
<<<<<<<<<<<<<<<<<
Sep 27 11:03:17 genepi1 kernel: scsi5: Dumping Card State
at program
address 0x9 Mode 0x33
Sep 27 11:03:17 genepi1 kernel: Card was paused
Sep 27 11:03:17 genepi1 kernel: INTSTAT[0x0] SELOID[0x1]
SELID[0x10]
HS_MAILBOX[0x0]
Sep 27 11:03:17 genepi1 kernel: INTCTL[0x80]
SEQINTSTAT[0x0]
SAVED_MODE[0x11] DFFSTAT[0x33]
Sep 27 11:03:17 genepi1 kernel: SCSISIGI[0x0]
SCSIPHASE[0x0]
SCSIBUS[0x0] LASTPHASE[0x1]
Sep 27 11:03:17 genepi1 kernel: SCSISEQ0[0x0]
SCSISEQ1[0x12]
SEQCTL0[0x0] SEQINTCTL[0x0]
Sep 27 11:03:17 genepi1 kernel: SEQ_FLAGS[0x0]
SEQ_FLAGS2[0x4]
QFREEZE_COUNT[0x7]
Sep 27 11:03:17 genepi1 kernel: KERNEL_QFREEZE_COUNT[0x6]
MK_MESSAGE_SCB[0xff00]
Sep 27 11:03:17 genepi1 kernel: MK_MESSAGE_SCSIID[0xff]
SSTAT0[0x0] SSTAT1[0x0]
Sep 27 11:03:17 genepi1 kernel: SSTAT2[0x0] SSTAT3[0x0]
PERRDIAG[0x0]
SIMODE1[0xa4]
Sep 27 11:03:17 genepi1 kernel: LQISTAT0[0x0] LQISTAT1[0x0]
LQISTAT2[0x0] LQOSTAT0[0x0]
Sep 27 11:03:17 genepi1 kernel: LQOSTAT1[0x0]
LQOSTAT2[0xe1]
Sep 27 11:03:17 genepi1 kernel:
Sep 27 11:03:17 genepi1 kernel: SCB Count = 4 CMDS_PENDING
= 0 LASTSCB
0xffff CURRSCB 0x3 NEXTSCB 0xff80
Sep 27 11:03:17 genepi1 kernel: qinstart = 44 qinfifonext =
45
Sep 27 11:03:17 genepi1 kernel: QINFIFO: 0x2
Sep 27 11:03:17 genepi1 kernel: WAITING_TID_QUEUES:
Sep 27 11:03:17 genepi1 kernel: Pending list:
Sep 27 11:03:17 genepi1 kernel: 2 FIFO_USE[0x0]
SCB_CONTROL[0x68]
SCB_SCSIID[0x17]
Sep 27 11:03:17 genepi1 kernel: Total 1
Sep 27 11:03:17 genepi1 kernel: Kernel Free SCB list: 3 1 0
Sep 27 11:03:17 genepi1 kernel: Sequencer Complete
DMA-inprog list:
Sep 27 11:03:17 genepi1 kernel: Sequencer Complete list:
Sep 27 11:03:17 genepi1 kernel: Sequencer DMA-Up and
Complete list:
Sep 27 11:03:17 genepi1 kernel: Sequencer On QFreeze and
Complete list:
Sep 27 11:03:17 genepi1 kernel:
Sep 27 11:03:17 genepi1 kernel:
Sep 27 11:03:17 genepi1 kernel: scsi5: FIFO0 Free, LONGJMP
== 0x80a3, SCB 0x3
Sep 27 11:03:17 genepi1 kernel: SEQIMODE[0x3f]
SEQINTSRC[0x0]
DFCNTRL[0x0] DFSTATUS[0x89]
Sep 27 11:03:17 genepi1 kernel: SG_CACHE_SHADOW[0x2]
SG_STATE[0x0]
DFFSXFRCTL[0x0]
Sep 27 11:03:17 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
SHADDR =
0x00, SHCNT = 0x0
Sep 27 11:03:17 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
CCSGCTL[0x10]
Sep 27 11:03:17 genepi1 kernel:
Sep 27 11:03:17 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP
== 0x8063, SCB 0x3
Sep 27 11:03:17 genepi1 kernel: SEQIMODE[0x3f]
SEQINTSRC[0x0]
DFCNTRL[0x0] DFSTATUS[0x89]
Sep 27 11:03:17 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP
== 0x8063, SCB 0x3
Sep 27 11:03:17 genepi1 kernel: SEQIMODE[0x3f]
SEQINTSRC[0x0]
DFCNTRL[0x0] DFSTATUS[0x89]
Sep 27 11:03:17 genepi1 kernel: SG_CACHE_SHADOW[0x2]
SG_STATE[0x0]
DFFSXFRCTL[0x0]
Sep 27 11:03:17 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
SHADDR =
0x00, SHCNT = 0x0
Sep 27 11:03:17 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
CCSGCTL[0x10]
Sep 27 11:03:17 genepi1 kernel: LQIN: 0x8 0x0 0x0 0x3 0x0
0x1 0x0 0x0
0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
Sep 27 11:03:17 genepi1 kernel: scsi5: LQISTATE = 0x0,
LQOSTATE = 0x0,
OPTIONMODE = 0x52
Sep 27 11:03:17 genepi1 kernel: scsi5: OS_SPACE_CNT = 0x20
MAXCMDCNT = 0x1
Sep 27 11:03:17 genepi1 kernel: scsi5: SAVED_SCSIID = 0x0
SAVED_LUN = 0x0
Sep 27 11:03:17 genepi1 kernel: SIMODE0[0xc]
Sep 27 11:03:17 genepi1 kernel: CCSCBCTL[0x0]
Sep 27 11:03:17 genepi1 kernel: scsi5: REG0 == 0xffff,
SINDEX = 0x104,
DINDEX = 0x104
Sep 27 11:03:17 genepi1 kernel: scsi5: SCBPTR == 0x3,
SCB_NEXT ==
0xff80, SCB_NEXT2 == 0xff80
Sep 27 11:03:17 genepi1 kernel: CDB 3 0 0 83 a 8c
Sep 27 11:03:17 genepi1 kernel: STACK: 0x0 0x0 0x0 0x0 0x0
0x0 0x0 0x0
Sep 27 11:03:17 genepi1 kernel:
<<<<<<<<<<<<<<<<<
Dump Card State Ends
>>>>>>>>>>>>>>>>>>
Sep 27 11:03:17 genepi1 kernel: scsi5:0:1:0: Cmd aborted
from QINFIFO
Sep 27 11:03:27 genepi1 kernel: scsi 5:0:1:1: Attempting to
queue an
ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
Sep 27 11:03:27 genepi1 kernel: scsi5: At time of recovery,
card was not paused
Sep 27 11:03:27 genepi1 kernel:
>>>>>>>>>>>>>>>>>>
Dump Card State
Begins
<<<<<<<<<<<<<<<<<
Sep 27 11:03:27 genepi1 kernel: scsi5: Dumping Card State
at program
address 0x22 Mode 0x33
Sep 27 11:03:27 genepi1 kernel: Card was paused
Sep 27 11:03:27 genepi1 kernel: INTSTAT[0x0] SELOID[0x1]
SELID[0x10]
HS_MAILBOX[0x0]
Sep 27 11:03:27 genepi1 kernel: INTCTL[0x80]
SEQINTSTAT[0x0]
SAVED_MODE[0x11] DFFSTAT[0x33]
Sep 27 11:03:27 genepi1 kernel: SCSISIGI[0x0]
SCSIPHASE[0x0]
SCSIBUS[0x0] LASTPHASE[0x1]
Sep 27 11:03:27 genepi1 kernel: SCSISEQ0[0x0]
SCSISEQ1[0x12]
SEQCTL0[0x0] SEQINTCTL[0x0]
Sep 27 11:03:27 genepi1 kernel: SEQ_FLAGS[0x0]
SEQ_FLAGS2[0x4]
QFREEZE_COUNT[0x7]
Sep 27 11:03:27 genepi1 kernel: KERNEL_QFREEZE_COUNT[0x6]
MK_MESSAGE_SCB[0xff00]
Sep 27 11:03:27 genepi1 kernel: MK_MESSAGE_SCSIID[0xff]
SSTAT0[0x0] SSTAT1[0x0]
Sep 27 11:03:27 genepi1 kernel: SSTAT2[0x0] SSTAT3[0x0]
PERRDIAG[0x0]
SIMODE1[0xa4]
Sep 27 11:03:27 genepi1 kernel: LQISTAT0[0x0] LQISTAT1[0x0]
LQISTAT2[0x0] LQOSTAT0[0x0]
Sep 27 11:03:27 genepi1 kernel: LQOSTAT1[0x0]
LQOSTAT2[0xe1]
Sep 27 11:03:27 genepi1 kernel:
Sep 27 11:03:27 genepi1 kernel: SCB Count = 4 CMDS_PENDING
= 0 LASTSCB
0xffff CURRSCB 0x3 NEXTSCB 0xff80
Sep 27 11:03:27 genepi1 kernel: qinstart = 44 qinfifonext =
45
Sep 27 11:03:27 genepi1 kernel: QINFIFO: 0x2
Sep 27 11:03:27 genepi1 kernel: WAITING_TID_QUEUES:
Sep 27 11:03:27 genepi1 kernel: Pending list:
Sep 27 11:03:27 genepi1 kernel: 2 FIFO_USE[0x0]
SCB_CONTROL[0x68]
SCB_SCSIID[0x17]
Sep 27 11:03:27 genepi1 kernel: Total 1
Sep 27 11:03:27 genepi1 kernel: Kernel Free SCB list: 3 1 0
Sep 27 11:03:27 genepi1 kernel: Sequencer Complete
DMA-inprog list:
Sep 27 11:03:27 genepi1 kernel: Sequencer Complete list:
Sep 27 11:03:27 genepi1 kernel: Sequencer DMA-Up and
Complete list:
Sep 27 11:03:27 genepi1 kernel: Sequencer On QFreeze and
Complete list:
Sep 27 11:03:27 genepi1 kernel:
Sep 27 11:03:27 genepi1 kernel:
Sep 27 11:03:27 genepi1 kernel: scsi5: FIFO0 Free, LONGJMP
== 0x80a3, SCB 0x3
Sep 27 11:03:27 genepi1 kernel: SEQIMODE[0x3f]
SEQINTSRC[0x0]
DFCNTRL[0x0] DFSTATUS[0x89]
Sep 27 11:03:27 genepi1 kernel: SG_CACHE_SHADOW[0x2]
SG_STATE[0x0]
DFFSXFRCTL[0x0]
Sep 27 11:03:Sep 27 11:03:27 genepi1 kernel: HADDR = 0x00,
HCNT = 0x0
CCSGCTL[0x10]
Sep 27 11:03:27 genepi1 kernel:
Sep 27 11:03:27 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP
== 0x8063, SCB 0x3
Sep 27 11:03:27 genepi1 kernel: SEQIMODE[0x3f]
SEQINTSRC[0x0]
DFCNTRL[0x0] DFSTATUS[0x89]
Sep 27 11:03:27 genepi1 kernel: SG_CACHE_SHADOW[0x2]
SG_STATE[0x0]
DFFSXFRCTL[0x0]
Sep 27 11:03:27 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
SHADDR =
0x00, SHCNT = 0x0
Sep 27 11:03:27 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
CCSGCTL[0x10]
Sep 27 11:03:27 genepi1 kernel: LQIN: 0x8 0x0 0x0 0x3 0x0
0x1 0x0 0x0
0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
Sep 27 11:03:27 genepi1 kernel: scsi5: LQISTATE = 0x0,
LQOSTATE = 0x0,
OPTIONMODE = 0x52
Sep 27 11:03:27 genepi1 kernel: scsi5: OS_SPACE_CNT = 0x20
MAXCMDCNT = 0x1
Sep 27 11:03:27 genepi1 kernel: scsi5: SAVED_SCSIID = 0x0
SAVED_LUN = 0x0
Sep 27 11:03:27 genepi1 kernel: SIMODE0[0xc]
Sep 27 11:03:27 genepi1 kernel: CCSCBCTL[0x0]
Sep 27 11:03:27 genepi1 kernel: scsi5: REG0 == 0xffff,
SINDEX = 0x104,
DINDEX = 0x104
Sep 27 11:03:27 genepi1 kernel: scsi5: SCBPTR == 0x3,
SCB_NEXT ==
0xff80, SCB_NEXT2 == 0xff80
Sep 27 11:03:27 genepi1 kernel: CDB 3 0 0 83 a 8c
Sep 27 11:03:27 genepi1 kernel: STACK: 0x1e 0x0 0x0 0x0 0x0
0x0 0x0 0x0
Sep 27 11:03:27 genepi1 kernel:
<<<<<<<<<<<<<<<<<
Dump Card State Ends
>>>>>>>>>>>>>>>>>>
Sep 27 11:03:27 genepi1 kernel: scsi5:0:1:1: Cmd aborted
from QINFIFO
Sep 27 11:03:27 genepi1 kernel: st 5:0:1:0: Device offlined
- not
ready after error recovery
Sep 27 11:03:27 genepi1 kernel: scsi 5:0:1:1: Device
offlined - not
ready after error recovery
Sep 27 11:07:00 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
(0x03:0x010D):
Invalid field in CDB:.
Sep 27 11:07:00 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
(0x03:0x0101):
Invalid command opcode:opcode=0xB8.
Sep 27 11:07:00 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
(0x03:0x0101):
Invalid command opcode:opcode=0xB8.
Sep 27 11:16:41 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
(0x03:0x010D):
Invalid field in CDB:.
Sep 27 11:16:41 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
(0x03:0x0101):
Invalid command opcode:opcode=0xB8.
Sep 27 11:16:41 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
(0x03:0x0101):
Invalid command opcode:opcode=0xB8.
Sep 27 11:16:51 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
(0x03:0x010D):
Invalid field in CDB:.
Sep 27 11:16:51 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
(0x03:0x0101):
Invalid command opcode:opcode=0xB8.
Sep 27 11:16:51 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
(0x03:0x0101):
Invalid command opcode:opcode=0xB8.
27 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5] SHADDR =
0x00, SHCNT = 0x0
Sep 27 11:03:27 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
CCSGCTL[0x10]
Sep 27 11:03:27 genepi1 kernel:
My Adaptec 29160 Ultra160 comes with testing software shown early in boot!
Next comes grub
--
fedora-list mailing list
fedora-list(a)redhat.com
To unsubscribe:
https://www.redhat.com/mailman/listinfo/fedora-list
Guidelines:
http://fedoraproject.org/wiki/Communicate/MailingListGuidelines
5701
days inactive
5701
days old
2 comments
2 participants
participants (2)
-
Fred Silsbee -
Gary Artim