10:37 p.m.
Greetings,
This evening when I installed my USB MicroSD reader into a USB port it
failed to be mounted.
My flash drives mount properly.
Looking at the log files I see:
Apr 21 23:12:54 brill kernel: usb 1-2: new high speed USB device using
ehci_hcd and address 7
Apr 21 23:12:54 brill kernel: usb 1-2: configuration #1 chosen from 1
choice
Apr 21 23:12:54 brill kernel: scsi11 : SCSI emulation for USB Mass Storage
devices
Apr 21 23:12:54 brill kernel: usb 1-2: New USB device found,
idVendor=090c, idProduct=6200
Apr 21 23:12:54 brill kernel: usb 1-2: New USB device strings: Mfr=1,
Product=2, SerialNumber=3
Apr 21 23:12:54 brill kernel: usb 1-2: Product: Generic USB2.0 card
Apr 21 23:12:54 brill kernel: usb 1-2: Manufacturer: Silicon Motion, Inc.
Apr 21 23:12:54 brill kernel: usb 1-2: SerialNumber: 12345678901234567890
Apr 21 23:12:59 brill kernel: scsi 11:0:0:0: Direct-Access Generic
USB SD Reader 1.00 PQ: 0 ANSI: 0 CCS
Apr 21 23:12:59 brill kernel: sd 11:0:0:0: [sdc] Attached SCSI removable
disk
Apr 21 23:12:59 brill kernel: sd 11:0:0:0: Attached scsi generic sg3 type
0
It stops there.
A few days ago when I mounted the reader and card, /var/log/messages read:
Apr 13 07:27:19 brill kernel: usb 3-1: USB disconnect, address 2
Apr 13 07:28:30 brill kernel: usb 1-1: new high speed USB device using
ehci_hcd and address 3
Apr 13 07:28:30 brill kernel: usb 1-1: configuration #1 chosen from 1
choice
Apr 13 07:28:30 brill kernel: usb 1-1: New USB device found,
idVendor=090c, idProduct=6200
Apr 13 07:28:30 brill kernel: usb 1-1: New USB device strings: Mfr=1,
Product=2, SerialNumber=3
Apr 13 07:28:30 brill kernel: usb 1-1: Product: Generic USB2.0 card
Apr 13 07:28:30 brill kernel: usb 1-1: Manufacturer: Silicon Motion, Inc.
Apr 13 07:28:30 brill kernel: usb 1-1: SerialNumber: 12345678901234567890
Apr 13 07:28:32 brill kernel: Initializing USB Mass Storage driver...
Apr 13 07:28:32 brill kernel: scsi6 : SCSI emulation for USB Mass Storage
devices
Apr 13 07:28:32 brill kernel: usbcore: registered new interface driver
usb-storage
Apr 13 07:28:32 brill kernel: USB Mass Storage support registered.
Apr 13 07:28:37 brill kernel: scsi 6:0:0:0: Direct-Access Generic USB
SD Reader 1.00 PQ: 0 ANSI: 0 CCS
Apr 13 07:28:37 brill kernel: sd 6:0:0:0: [sdc] 7745536 512-byte hardware
sectors (3966 MB)
Apr 13 07:28:37 brill kernel: sd 6:0:0:0: [sdc] Write Protect is off
Apr 13 07:28:37 brill kernel: sd 6:0:0:0: [sdc] Assuming drive cache:
write through
Apr 13 07:28:37 brill kernel: sd 6:0:0:0: [sdc] 7745536 512-byte hardware
sectors (3966 MB)
Apr 13 07:28:37 brill kernel: sd 6:0:0:0: [sdc] Write Protect is off
Apr 13 07:28:37 brill kernel: sd 6:0:0:0: [sdc] Assuming drive cache:
write through
Apr 13 07:28:37 brill kernel: sdc: sdc1
Apr 13 07:28:37 brill kernel: sd 6:0:0:0: [sdc] Attached SCSI removable
disk
Apr 13 07:28:37 brill kernel: sd 6:0:0:0: Attached scsi generic sg3 type 0
Apr 13 07:28:40 brill gnome-keyring-daemon[3199]: adding removable
location: volume_uuid_565F_311A at /media/Kingston
Apr 13 07:28:40 brill hald: mounted /dev/sdc1 on behalf of uid 500
Any suggestions on how to mount this card?
Much thanks.
Max Pyziur
pyz(a)brama.com
1:15 p.m.
Max Pyziur wrote:
Greetings,
This evening when I installed my USB MicroSD reader into a USB port it
failed to be mounted.
My flash drives mount properly.
Looking at the log files I see:
Apr 21 23:12:54 brill kernel: usb 1-2: new high speed USB device using
ehci_hcd and address 7
Apr 21 23:12:54 brill kernel: usb 1-2: configuration #1 chosen from 1
choice
Apr 21 23:12:54 brill kernel: scsi11 : SCSI emulation for USB Mass
Storage devices
Apr 21 23:12:54 brill kernel: usb 1-2: New USB device found,
idVendor=090c, idProduct=6200
Apr 21 23:12:54 brill kernel: usb 1-2: New USB device strings: Mfr=1,
Product=2, SerialNumber=3
Apr 21 23:12:54 brill kernel: usb 1-2: Product: Generic USB2.0 card
Apr 21 23:12:54 brill kernel: usb 1-2: Manufacturer: Silicon Motion, Inc.
Apr 21 23:12:54 brill kernel: usb 1-2: SerialNumber: 12345678901234567890
Apr 21 23:12:59 brill kernel: scsi 11:0:0:0: Direct-Access Generic
USB SD Reader 1.00 PQ: 0 ANSI: 0 CCS
Apr 21 23:12:59 brill kernel: sd 11:0:0:0: [sdc] Attached SCSI removable
disk
Apr 21 23:12:59 brill kernel: sd 11:0:0:0: Attached scsi generic sg3 type 0
It stops there.
<--------------------------[ snip ]------------------->
Any suggestions on how to mount this card?
Much thanks.
Max Pyziur
pyz(a)brama.com
The differences I see is that it looks like the usb_storage module
is already mounted, and the card is not being seen. Are you sure the
mini-SD card is properly seated in the reader?
Mikkel?\
--
Do not meddle in the affairs of dragons,
for thou art crunchy and taste good with Ketchup!
2:30 p.m.
Mikkel L. Ellertson wrote:
Max Pyziur wrote:
>
> This evening when I installed my USB MicroSD reader into a USB port it
> failed to be mounted.
<snip>
> Apr 21 23:12:54 brill kernel: usb 1-2: Product: Generic USB2.0
card
> Apr 21 23:12:54 brill kernel: usb 1-2: Manufacturer: Silicon Motion, Inc.
> Apr 21 23:12:54 brill kernel: usb 1-2: SerialNumber: 12345678901234567890
> Apr 21 23:12:59 brill kernel: scsi 11:0:0:0: Direct-Access Generic
> USB SD Reader 1.00 PQ: 0 ANSI: 0 CCS
The differences I see is that it looks like the usb_storage module
is already mounted, and the card is not being seen. Are you sure the
mini-SD card is properly seated in the reader?
so it does appear.
i have a multi card reader and his list is similar. tho it does show an
interesting serial number.
all tho he should be able to plug a card in and see it, it would be worth
wild to plug in card before boot to see what happens.
--
peace out.
tc,hago.
g
.
****
in a free world without fences, who needs gates.
**
help microsoft stamp out piracy - give linux to a friend today
**
to mess up a linux box, you need to work at it;
to mess up an ms windows box, you just need to *look at* it.
**
learn linux:
'Rute User's Tutorial and Exposition' http://rute.2038bug.com/index.html
'The Linux Documentation Project' http://www.tldp.org/
'LDP HOWTO-index' http://www.tldp.org/HOWTO/HOWTO-INDEX/index.html
'HowtoForge' http://howtoforge.com/
****
8:30 p.m.
On Tue, Apr 21, 2009 at 7:37 PM, Max Pyziur <pyz(a)brama.com> wrote:
Greetings,
This evening when I installed my USB MicroSD reader into a USB port it
failed to be mounted.
My flash drives mount properly.
Looking at the log files I see:
Apr 21 23:12:54 brill kernel: usb 1-2: new high speed USB device using
ehci_hcd and address 7
Apr 21 23:12:54 brill kernel: usb 1-2: configuration #1 chosen from 1 choice
Apr 21 23:12:54 brill kernel: scsi11 : SCSI emulation for USB Mass Storage
devices
Apr 21 23:12:54 brill kernel: usb 1-2: New USB device found, idVendor=090c,
idProduct=6200
Apr 21 23:12:54 brill kernel: usb 1-2: New USB device strings: Mfr=1,
Product=2, SerialNumber=3
Apr 21 23:12:54 brill kernel: usb 1-2: Product: Generic USB2.0 card
Apr 21 23:12:54 brill kernel: usb 1-2: Manufacturer: Silicon Motion, Inc.
Apr 21 23:12:54 brill kernel: usb 1-2: SerialNumber: 12345678901234567890
Apr 21 23:12:59 brill kernel: scsi 11:0:0:0: Direct-Access Generic USB
SD Reader 1.00 PQ: 0 ANSI: 0 CCS
Apr 21 23:12:59 brill kernel: sd 11:0:0:0: [sdc] Attached SCSI removable
disk
Apr 21 23:12:59 brill kernel: sd 11:0:0:0: Attached scsi generic sg3 type 0
It stops there.
A few days ago when I mounted the reader and card, /var/log/messages read:
Apr 13 07:27:19 brill kernel: usb 3-1: USB disconnect, address 2
Apr 13 07:28:30 brill kernel: usb 1-1: new high speed USB device using
ehci_hcd and address 3
Apr 13 07:28:30 brill kernel: usb 1-1: configuration #1 chosen from 1 choice
Apr 13 07:28:30 brill kernel: usb 1-1: New USB device found, idVendor=090c,
idProduct=6200
Apr 13 07:28:30 brill kernel: usb 1-1: New USB device strings: Mfr=1,
Product=2, SerialNumber=3
Apr 13 07:28:30 brill kernel: usb 1-1: Product: Generic USB2.0 card
Apr 13 07:28:30 brill kernel: usb 1-1: Manufacturer: Silicon Motion, Inc.
Apr 13 07:28:30 brill kernel: usb 1-1: SerialNumber: 12345678901234567890
Apr 13 07:28:32 brill kernel: Initializing USB Mass Storage driver...
Apr 13 07:28:32 brill kernel: scsi6 : SCSI emulation for USB Mass Storage
devices
Apr 13 07:28:32 brill kernel: usbcore: registered new interface driver
usb-storage
Apr 13 07:28:32 brill kernel: USB Mass Storage support registered.
Apr 13 07:28:37 brill kernel: scsi 6:0:0:0: Direct-Access Generic USB
SD Reader 1.00 PQ: 0 ANSI: 0 CCS
Apr 13 07:28:37 brill kernel: sd 6:0:0:0: [sdc] 7745536 512-byte hardware
sectors (3966 MB)
Apr 13 07:28:37 brill kernel: sd 6:0:0:0: [sdc] Write Protect is off
Apr 13 07:28:37 brill kernel: sd 6:0:0:0: [sdc] Assuming drive cache: write
through
Apr 13 07:28:37 brill kernel: sd 6:0:0:0: [sdc] 7745536 512-byte hardware
sectors (3966 MB)
Apr 13 07:28:37 brill kernel: sd 6:0:0:0: [sdc] Write Protect is off
Apr 13 07:28:37 brill kernel: sd 6:0:0:0: [sdc] Assuming drive cache: write
through
Apr 13 07:28:37 brill kernel: sdc: sdc1
Apr 13 07:28:37 brill kernel: sd 6:0:0:0: [sdc] Attached SCSI removable disk
Apr 13 07:28:37 brill kernel: sd 6:0:0:0: Attached scsi generic sg3 type 0
Apr 13 07:28:40 brill gnome-keyring-daemon[3199]: adding removable location:
volume_uuid_565F_311A at /media/Kingston
Apr 13 07:28:40 brill hald: mounted /dev/sdc1 on behalf of uid 500
Any suggestions on how to mount this card?
Much thanks.
Max Pyziur
pyz(a)brama.com
What type of media did you put into the reader? Verify that your
reader is capable of reading SDHC media. Many are not.
10:11 p.m.
Kam Leo wrote:
On Tue, Apr 21, 2009 at 7:37 PM, Max Pyziur <pyz(a)brama.com> wrote:
>
> Greetings,
>
> This evening when I installed my USB MicroSD reader into a USB port it
> failed to be mounted.
<snip>
> Apr 21 23:12:54 brill kernel: usb 1-2: Product: Generic USB2.0
card
> Apr 21 23:12:54 brill kernel: usb 1-2: Manufacturer: Silicon Motion, Inc.
> Apr 21 23:12:54 brill kernel: usb 1-2: SerialNumber: 12345678901234567890
> Apr 21 23:12:59 brill kernel: scsi 11:0:0:0: Direct-Access Generic USB
> SD Reader 1.00 PQ: 0 ANSI: 0 CCS
<snip>
What type of media did you put into the reader? Verify that your
reader is capable of reading SDHC media. Many are not.
op states it is a microsd reader. log states it is an sd reader/
why would it not be able to read an sd card?
also, please trim unnecessary history when you reply to a post. thank you.
--
peace out.
tc,hago.
g
.
****
in a free world without fences, who needs gates.
**
help microsoft stamp out piracy - give linux to a friend today
**
to mess up a linux box, you need to work at it;
to mess up an ms windows box, you just need to *look at* it.
**
learn linux:
'Rute User's Tutorial and Exposition' http://rute.2038bug.com/index.html
'The Linux Documentation Project' http://www.tldp.org/
'LDP HOWTO-index' http://www.tldp.org/HOWTO/HOWTO-INDEX/index.html
'HowtoForge' http://howtoforge.com/
****
2:11 p.m.
On Sun, Apr 26, 2009 at 7:11 PM, g <geleem(a)bellsouth.net> wrote:
Kam Leo wrote:
On Tue, Apr 21, 2009 at 7:37 PM, Max Pyziur <pyz(a)brama.com> wrote:
>>
>> Greetings,
>>
>> This evening when I installed my USB MicroSD reader into a USB port it
>> failed to be mounted.
<snip>
>> Apr 21 23:12:54 brill kernel: usb 1-2: Product: Generic USB2.0 card
>> Apr 21 23:12:54 brill kernel: usb 1-2: Manufacturer: Silicon Motion, Inc.
>> Apr 21 23:12:54 brill kernel: usb 1-2: SerialNumber: 12345678901234567890
>> Apr 21 23:12:59 brill kernel: scsi 11:0:0:0: Direct-Access Generic USB
>> SD Reader 1.00 PQ: 0 ANSI: 0 CCS
<snip>
> What type of media did you put into the reader? Verify that your
> reader is capable of reading SDHC media. Many are not.
op states it is a microsd reader. log states it is an sd reader/
why would it not be able to read an sd card?
FORMAT. Like their standard sized SD and SDHC counterparts there are
micro-SD and micro-SDHC cards. SD cards have up to 2 GB memory while
SDHC have capacities in the range of 4 - 32 GB. Mechanical adapters
can enable micro cards to be plugged into SD readers, but the adapters
do not accommodate format changes. Contrary to what the SD Association
says about compatibility and interoperability older SD readers are not
able to interface with the higher capacity media. When you purchase a
reader or media you need to make sure that they are compatible.
Note: SDXC is coming out. I'm certain the majority of existing readers
will not be able to handle this new format.
peace out.
tc,hago.
g
.
3:32 p.m.
Kam Leo wrote:
FORMAT. Like their standard sized SD and SDHC counterparts there are
i am familiar with *sizes* of sd series.
op, max pyziur, stated in his post;
>>> This evening when I installed my USB MicroSD reader into
a USB port it
>>> failed to be mounted.
in my reply to your post, i stated sd card, as he does not mention size
of card and i am giving him credit to know what card he has. i may be
incorrect in doing so.
in your post, you state;
>> What type of media did you put into the reader? Verify that
your
>> reader is capable of reading SDHC media. Many are not.
you are presuming that max has an sdhc card and that he is trying to
read it in an sd reader.
this really should be put on hold until max replies with a conformation of
just what card and reader he has.
--
peace out.
tc,hago.
g
.
****
in a free world without fences, who needs gates.
**
help microsoft stamp out piracy - give linux to a friend today
**
to mess up a linux box, you need to work at it;
to mess up an ms windows box, you just need to *look at* it.
**
learn linux:
'Rute User's Tutorial and Exposition' http://rute.2038bug.com/index.html
'The Linux Documentation Project' http://www.tldp.org/
'LDP HOWTO-index' http://www.tldp.org/HOWTO/HOWTO-INDEX/index.html
'HowtoForge' http://howtoforge.com/
****
4:07 p.m.
Much thanks for all of the replies and apologies for my delay in
contributing, especially since I started this thread.
The card is a 4GB MicroSDHC marketed by Kingston. I use it in my Palm
Centro phone.
Prior to reporting the initial error, I tried several possible solutions,
including remounting in a different USB slot, reseating it in the USB
adapter, rebooting the machine (an Intel Core 2 Duo 64 bit desktop)
(apologies, as yet I don't know what services or other processes/modules
are associated with the automounting of the USB MicroSD card reader).
None, at the time worked.
After reporting the error, I tried it on an i386 laptop and it automounted
successfully.
The following day, after doing a number of yum updates, I tried mounting
it on the Core 2 desktop, and it worked. For me and others interested in
this issue, that doesn't resolve why the card/card reader stopped
automounting.
However, now I can't replicate the problem.
But thanks to all for the help.
Max Pyziur
pyz(a)brama.com
Kam Leo wrote:
> FORMAT. Like their standard sized SD and SDHC counterparts there are
i am familiar with *sizes* of sd series.
op, max pyziur, stated in his post;
>>>> This evening when I installed my USB MicroSD reader into a USB port
>>>> it
>>>> failed to be mounted.
in my reply to your post, i stated sd card, as he does not mention size
of card and i am giving him credit to know what card he has. i may be
incorrect in doing so.
in your post, you state;
>>> What type of media did you put into the reader? Verify that your
>>> reader is capable of reading SDHC media. Many are not.
you are presuming that max has an sdhc card and that he is trying to
read it in an sd reader.
this really should be put on hold until max replies with a conformation of
just what card and reader he has.
--
peace out.
tc,hago.
g
.
****
in a free world without fences, who needs gates.
**
help microsoft stamp out piracy - give linux to a friend today
**
to mess up a linux box, you need to work at it;
to mess up an ms windows box, you just need to *look at* it.
**
learn linux:
'Rute User's Tutorial and Exposition' http://rute.2038bug.com/index.html
'The Linux Documentation Project' http://www.tldp.org/
'LDP HOWTO-index' http://www.tldp.org/HOWTO/HOWTO-INDEX/index.html
'HowtoForge' http://howtoforge.com/
****
--
fedora-list mailing list
fedora-list(a)redhat.com
To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-list
Guidelines:
http://fedoraproject.org/wiki/Communicate/MailingListGuidelines
5494
days inactive
5499
days old
7 comments
4 participants
participants (4)
-
g -
Kam Leo -
Max Pyziur -
Mikkel